Search NASA⌕ Search

Engineering topics

Murrow, Harold N.

Publications and source records attributed to Murrow, Harold N..

11 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

Measurement of atmospheric turbulence

The material contained is primarily a compilation of information that has already been published. The attached reference list should be adequate for clarifying points to any detail desired. The purpose is to provide a description of the methodology required for measuring atmospheric turbulence in the form of true gust velocity. The content will include instrumentation requirements and selections used, flight assessments of the measurement system, some data reduction considerations, and finally some typical data obtained.

Murrow, Harold N.↗
NASA NTRS1990

Structures technology development for hypersonic vehicles

This paper summarizes some of the efforts to advance hypersonic structures technology through the National Aero-Space Plane (NASP) Structures Technology Maturation Program. The ranges of expected structural loads and results from analysis and test activities are described. Topics briefly covered include shock impingement effects on aerothermal loads, actively-cooled structures concepts and test results to date for leading edges and panels, design and fabrication of a carbon-carbon control surface, a program for predicting performance of metal matrix composites, an analysis and sizing procedure for thermal structures, and some recently-developed test fixtures for seals, thermal insulation, and actively-cooled panels.

Camarda, Charles J.↗
NASA NTRS1990

Structures and materials technology for hypersonic aerospacecraft

Major considerations in structural design of a transatmospheric aerospacecraft are discussed. The general direction of progress in structures and materials technology is indicated, and technical areas in structures and materials where further research and development is necessary are indicated. Various structural concepts under study and materials which appear to be most applicable are discussed. Structural design criteria are discussed with particular attention to the factor-of-safety approach and the probabilistic approach. Structural certification requirements for the aerospacecraft are discussed. The kinds of analyses and tests which would be required to certify the structural integrity, safety, and durability of the aerospacecraft are discussed, and the type of test facility needed to perform structural certification tests is identified.

Mccomb, Harvey G., Jr.↗
NASA NTRS1989

Enabling technologies research and development structures

The technology-development areas of most critical importance to the definition of the NASP vehicle's airframe and integrated propulsion systems are discussed with a view to the progress made to date and the prospects for the expansion of a definitive NASP design data base on materials, structures, etc. It is necessary to achieve a very low structural-mass fraction, to withstand 6000 F radiation equilibrium fuselage nosecap temperatures, to manage an extensive active cooling network for both airframe and propulsion system capable of dissipating 10,000 BTU/sq ft-sec thermal fluxes, to maintain effective hot-gas sealing, and to manufacture high temperature effectiveness-retaining control surfaces. An account is given of successes thus far achieved.

Davis, John G., Jr.↗
NASA NTRS1989

NACA/NASA research related to evolution of U.S. gust design criteria

This paper traces the evolution of gust design criteria in the U.S. particularly from the standpoint of research that was used in the substantiation for the various versions in the evolution. The mathematical models of airplanes and of atmospheric turbulence and their rationale are described. Emphasis is given to the revisions and refinements made starting in the 1920's up to the present time. The major steps, beginning with the sharp edged gust formula, are traced through the modified formula specifying ramp-platform gusts and later to one-minus-cosine gusts and finally to criteria for continuous gust analyses. The influence of aircraft design developments on design criteria development needs is also addressed. A brief summary of military criteria is included. Significant discussion is devoted to measurements that have been made, including onboard recordings, to provide an extensive data base of (1) atmospheric turbulence experienced in routine flight operations, (2) specially-instrumented research aircraft measurements to provide atmospheric characterization for various flight and meteorological conditions, and (3) comparisons of measured and calculated aircraft responses in turbulence. Some features of the instrumentation used will be depicted.

Murrow, Harold N.↗
NASA NTRS1987

Measurements of atmospheric turbulence

Various types of atmospheric turbulence measurements are addressed for the purpose of stimulating discussion relative to available data. An outline of these various types of measurements are discussed. Some specific results of detailed characterization studies made at NASA Langley are emphasized. The most recent reports on statistics of turbulence encounters for various types of aircraft operations are summarized. Special severe encounter studies and reference to remote sensing are also included. Wind shear is considered to be a special topic and is not covered.

Murrow, Harold N.↗
NASA NTRS1967

Flight Tests of a 40-Foot Nominal Diameter Modified Ringsail Parachute Deployed at Mach 1.64 and Dynamic Pressure of 9.1 Pounds Per Square Foot

A ringsail parachute, which had a nominal diameter of 40 feet (12.2 meters) and reference area of 1256 square feet (117 m(exp 2)) and was modified to provide a total geometric porosity of 15 percent of the reference area, was flight tested as part of the rocket launch portion of the NASA Planetary Entry Parachute Program. The payload for the flight test was an instrumented capsule from which the test parachute was ejected by a deployment mortar when the system was at a Mach number of 1.64 and a dynamic pressure of 9.1 pounds per square foot (43.6 newtons per m(exp 2)). The parachute deployed to suspension line stretch in 0.45 second with a resulting snatch force of 1620 pounds (7200 newtons). Canopy inflation began 0.07 second later and the parachute projected area increased slowly to a maximum of 20 percent of that expected for full inflation. During this test, the suspension lines twisted, primarily because the partially inflated canopy could not restrict the twisting to the attachment bridle and risers. This twisting of the suspension lines hampered canopy inflation at a time when velocity and dynamic-pressure conditions were more favorable.

TESTS↗
NASA NTRS1967

Flight Test of 31.2 Diameter Modified Ringsail Parachute Deployed at Mach 1.39, Dynamic Pressure 11 Pounds per Square Foot

A 31.2-foot (9.51 meter) nominal diameter (reference area 764 ft(exp 2) (71.0 m(exp 2)) ringsail parachute modified to provide 15-percent geometric porosity was flight tested while attached to a 201-pound mass (91.2 kilogram) instrumented payload as part of the rocket launch portion of the NASA Planetary Entry Parachute Program (PEPP). The parachute deployment was initiated by the firing of a mortar at a Mach number of 1.39 and a dynamic pressure of 11.0 lb/ft(exp 2) (527 newtons/m(exp 2)) at an altitude of 122,500 feet (37.3 kilometers). The parachute deployed to suspension-line stretch (snatch force) in 0.35 second, and 0.12 second later the drag force increase associated with parachute inflation began. The parachute inflated in 0.24 second to the full-open condition for a total elapsed opening time of 0.71 second. The maximum opening load of 3970 pounds (17,700 newtons) came at the time the parachute was just fully opened. During the deceleration period, the parachute exhibited an average drag coefficient of 0.52 and oscillations of the parachute canopy were less than 5 degrees. During the steady-state terminal descent portion of the test period, the average effective drag coefficient (based on vertical descent velocity) was 0.52.

TESTS↗
NASA NTRS1959

An Analysis of Flight-Test Measurements of the Wing Structural Deformations in Rough Air of a Large Flexible Swept-Wing Airplane

An analysis is made of wing deflection and streamwise twist measurements in rough-air flight of a large flexible swept-wing bomber. Random-process techniques are employed in analyzing the data in order to describe the magnitude and characteristics of the wing deflection and twist responses to rough air. Power spectra and frequency-response functions for the wing deflection and twist responses at several spanwise stations are presented. The frequency-response functions describe direct and absolute response characteristics to turbulence and provide a convenient basis for assessing analytic calculation techniques. The wing deformations in rough air are compared with the expected deformations for quasi-static loadings of the same magnitude, and the amplifications are determined. The results obtained indicate that generally the deflections are amplified by a small amount, while the streamwise twists are amplified by factors of the order of 2.0. The magnitudes of both the deflection velocities and the twist angles are shown to have significant effects on the local angles of attack at the various stations and provide the main source of aerodynamic loading, particularly at frequencies in the vicinity of the first wing-vibration mode.

Murrow, Harold N.↗