Search NASA⌕ Search

Engineering topics

Murthy, Durbha V.

Publications and source records attributed to Murthy, Durbha V..

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1999

Advanced Subsonic Technology (AST) Area of Interest (AOI) 6: Develop and Validate Aeroelastic Codes for Turbomachinery

AlliedSignal Engines, in cooperation with NASA GRC (National Aeronautics and Space Administration Glenn Research Center), completed an evaluation of recently-developed aeroelastic computer codes using test cases from the AlliedSignal Engines fan blisk and turbine databases. Test data included strain gage, performance, and steady-state pressure information obtained for conditions where synchronous or flutter vibratory conditions were found to occur. Aeroelastic codes evaluated included quasi 3-D UNSFLO (MIT Developed/AE Modified, Quasi 3-D Aeroelastic Computer Code), 2-D FREPS (NASA-Developed Forced Response Prediction System Aeroelastic Computer Code), and 3-D TURBO-AE (NASA/Mississippi State University Developed 3-D Aeroelastic Computer Code). Unsteady pressure predictions for the turbine test case were used to evaluate the forced response prediction capabilities of each of the three aeroelastic codes. Additionally, one of the fan flutter cases was evaluated using TURBO-AE. The UNSFLO and FREPS evaluation predictions showed good agreement with the experimental test data trends, but quantitative improvements are needed. UNSFLO over-predicted turbine blade response reductions, while FREPS under-predicted them. The inviscid TURBO-AE turbine analysis predicted no discernible blade response reduction, indicating the necessity of including viscous effects for this test case. For the TURBO-AE fan blisk test case, significant effort was expended getting the viscous version of the code to give converged steady flow solutions for the transonic flow conditions. Once converged, the steady solutions provided an excellent match with test data and the calibrated DAWES (AlliedSignal 3-D Viscous Steady Flow CFD Solver). However, efforts expended establishing quality steady-state solutions prevented exercising the unsteady portion of the TURBO-AE code during the present program. AlliedSignal recommends that unsteady pressure measurement data be obtained for both test cases examined for use in aeroelastic code validation.

Gardner, Kevin D.↗
NASA NTRS1998

Efficient Aeroelastic Analysis of Propulsion Turbomachinery

The purpose of this report is to provide a description of the overall thrust, past relevant accomplishments and future work for research that was performed on the titled project. The purpose of this work was to perform applied research at the NASA Lewis Research Center in the area of the aeroelastic behavior of turbomachinery used in air-breathing propulsion. This activity was undertaken in close cooperation with the Structural Dynamics Branch of the Structures Division at NASA Lewis.

Keith, Theo G., Jr.↗
NASA NTRS1997

Aeroelastic Analysis of Counter Rotation Fans

Aeroelastic problems in turbomachinery and propfans can be static or dynamic in nature. The analysis of static aeroelastic problems is involved primarily with determination: (a) of the shape of the blades and the steady aerodynamic loads on the blades (which are inter-dependent), (b) of the resultant steady stresses and (c) of the static instability (divergence) margin, if applicable. In this project, we were concerned exclusively with dynamic aeroelastic behavior. The analysis of dynamic aeroelastic problems is involved with the determination: (a) of the unsteady aerodynamic loads on blades and the dynamic motion of the blades (which are again inter-dependent), (b) of the resultant dynamic stresses and their effect on fatigue life and (c) of the dynamic instability (flutter), if applicable. There are two primary dynamic aeroelastic phenomena of interest to designers of turbomachinery and propfans: flutter and forced response. Flutter generally refers to the occurrence of rapidly growing self-excited oscillations leading to catastrophic failure of the blade. When certain nonlinear phenomena are present, flutter response may lead to a potentially dangerous limit cycle oscillation rather than an immediate catastrophic failure. Forced response generally refers to the steady-state oscillations that occur as a consequence of excitations external to the rotor in question. These excitations typically result from the presence of upstream obstructions, inflow distortions, downstream obstructions, or mechanical sources such as tip-casing contact or shaft and gear meshing. Significant forced response leads to blade fatigue, and at design conditions, generally contributes to a degradation of blade life. At other operating conditions, forced response may lead to catastrophic failure due to severe blade fatigue in a short duration of time.

Keith, Theo G., Jr.↗
NASA NTRS1996

Aeroelastic Analysis of Turbomachinery for Space Propulsion

The purpose of this report is to provide a description of the overall thrust, past relevant accomplishments and future work for research that was performed on the titled project. The purpose of this work was to perform applied research at the NASA Lewis Research Center in the area of the aeroelastic behavior of turbomachinery used in air-breathing propulsion. This activity was undertaken in close cooperation with the Structural Dynamics Branch of the Structures Division at NASA Lewis.

Keith, Theo G., Jr.↗
NASA NTRS1994

NASA Lewis Research Center Workshop on Forced Response in Turbomachinery

A summary of the NASA Lewis Research Center (LeRC) Workshop on Forced Response in Turbomachinery in August, 1993 is presented. It was sponsored by the following NASA organizations: Structures, Space Propulsion Technology, and Propulsion Systems Divisions of NASA LeRC and the Aeronautics and Advanced Concepts & Technology Offices of NASA Headquarters. In addition, the workshop was held in conjunction with the GUIde (Government/Industry/Universities) Consortium on Forced Response. The workshop was specifically designed to receive suggestions and comments from industry on current research at NASA LeRC in the area of forced vibratory response of turbomachinery blades which includes both computational and experimental approaches. There were eight presentations and a code demonstration. Major areas of research included aeroelastic response, steady and unsteady fluid dynamics, mistuning, and corresponding experimental work.

Stefko, George L.↗
NASA NTRS1993

Aeroelastic dynamics of mistuned blade assemblies with closely spaced blade modes

The aeroelastic characteristics of tuned and randomly mistuned blade assemblies which possess two blade-alone natural modes with close frequencies are studied. Modal interactions among the two blade modes are shown to be come extremely significant for small frequency separation. The two distinct loci of the aeroelastic eigenvalues, which characterize an assembly with well separated modes, fully merge into a single root locus as the blade-mode frequency separation vanishes. Also, while in the case of well separated blade modes the introduction of random mistuning into one blade mode affects only the assembly modes which are predominantly of that blade-mode type, mistuning results in the localization of all the assembly modes when the blade-alone natural frequencies are close. Results indicate that in the case of closely-spaced blade modes a single-degree of freedom blade model yields qualitatively erroneous results and that an N-blade assembly with two close blade modes behaves like an equivalent 2Nb-blade assembly with a single blade mode.

Pierre, Christophe↗
NASA NTRS1993

Forced response of mistuned bladed disk assemblies

A complete analytic model of mistuned bladed disk assemblies, designed to simulate the dynamical behavior of these systems, is analyzed. The model incorporates a generalized method for describing the mistuning of the assembly through the introduction of specific mistuning modes. The model is used to develop a computational bladed disk assembly model for a series of parametric studies. Results are presented demonstrating that the response amplitudes of bladed disk assemblies depend both on the excitation mode and on the mistune mode.

Watson, Brian C.↗
NASA NTRS1992

An efficient constraint to account for mistuning effects in the optimal design of engine rotors

Blade-to-blade differences in structural properties, unavoidable in practice due to manufacturing tolerances, can have significant influence on the vibratory response of engine rotor blade. Accounting for these differences, also known as mistuning, in design and in optimization procedures is generally not possible. This note presents an easily calculated constraint that can be used in design and optimization procedures to control the sensitivity of final designs to mistuning.

Murthy, Durbha V.↗
NASA NTRS1992

Stochastic sensitivity measure for mistuned high-performance turbines

A stochastic measure of sensitivity is developed in order to predict the effects of small random blade mistuning on the dynamic aeroelastic response of turbomachinery blade assemblies. This sensitivity measure is based solely on the nominal system design (i.e., on tuned system information), which makes it extremely easy and inexpensive to calculate. The measure has the potential to become a valuable design tool that will enable designers to evaluate mistuning effects at a preliminary design stage and thus assess the need for a full mistuned rotor analysis. The predictive capability of the sensitivity measure is illustrated by examining the effects of mistuning on the aeroelastic modes of the first stage of the oxidizer turbopump in the Space Shuttle Main Engine. Results from a full analysis mistuned systems confirm that the simple stochastic sensitivity measure predicts consistently the drastic changes due to misturning and the localization of aeroelastic vibration to a few blades.

Murthy, Durbha V.↗
NASA NTRS1992

FREPS - A forced response prediction system for turbomachinery blade rows

FREPS (Forced REsponse Predicition System) is a software system that integrates structural dynamic, steady and unsteady aerodynamic analyses to efficiently predict the forced dynamic stresses of turbomachinery blades to aerodynamic and mechanical excitations. The program performs flutter analysis also. The FREPS system uses a modal approach for aeroelastic analysis. The structural dynamic analysis is based on MSC/NASTRAN, the steady aerodynamic analysis is based on potential theory and the unsteady aerodynamic analysis is based on a linearization of the non-uniform potential mean flow. The capabilities of the program are described and illustrated by application to the High Pressure Oxygen Turbopump turbine of the Space Shuttle Main Engine.

Murthy, Durbha V.↗
NASA NTRS1991

Aeroelastic modal characteristics of mistuned blade assemblies: Mode localization and loss of eigenstructure

An investigation of the effects of small mistuning on the aeroelastic modes of bladed disk assemblies with aerodynamic coupling between blades is presented. The cornerstone of the approach is the use and development of perturbation methods that exhibit the crucial role of the interblade coupling and yield general findings regarding mistuning effects. It is shown that blade assemblies with weak aerodynamic interblade coupling are highly sensitive to small blade mistuning, and that their dynamics is quantitatively altered in the following ways: the regular pattern that characterizes the root locus of the tuned aeroelastic eigenvalues in the complex plane is totally lost; the aeroelastic mode shapes becomes severely localized to only a few blades of the assembly and lose their constant interblade phase angle feature; and curve veering phenomena take place when the eigenvalues are plotted versus a mistuning parameter.

Pierre, Christophe↗
NASA NTRS1991

Localization of aeroelastic modes in mistuned high-energy turbines

The effects of blade mistuning on the aerodynamic characteristics of a class of bladed-disk assemblies, namely high energy turbines, are discussed. The specific rotor analyzed is the first stage of turbine blades of the oxidizer turbopump in the Space Shuttle Main Engine. The common occurrence of fatigue cracks for these turbine blades indicates the possibility of high dynamic loading. Since mistuning under conditions of weak interblade coupling has been shown to increase blade response amplitudes drastically for simple structural models of blade assemblies, it provides a plausible explanation for the occurrence of cracks. The focus here is on the effects of frequency mistuning on the aeroelastic stability of the assembly and on the aeroelastic mode shapes.

Smith, Todd E.↗
NASA NTRS1991

Efficient computation of aerodynamic influence coefficients for aeroelastic analysis on a transputer network

Aeroelastic analysis is multi-disciplinary and computationally expensive. Hence, it can greatly benefit from parallel processing. As part of an effort to develop an aeroelastic capability on a distributed memory transputer network, a parallel algorithm for the computation of aerodynamic influence coefficients is implemented on a network of 32 transputers. The aerodynamic influence coefficients are calculated using a 3-D unsteady aerodynamic model and a parallel discretization. Efficiencies up to 85 percent were demonstrated using 32 processors. The effect of subtask ordering, problem size, and network topology are presented. A comparison to results on a shared memory computer indicates that higher speedup is achieved on the distributed memory system.

Janetzke, David C.↗
NASA NTRS1991

Aeroelastic modal characteristics of mistuned blade assemblies - Mode localization and loss of eigenstructure

An investigation of the effects of small mistuning on the aeroelastic modes of bladed-disk assemblies with aerodynamic coupling between blades is presented. The cornerstone of the approach is the use and development of perturbation methods that exhibit the crucial role of the interblade coupling and yield general findings regarding mistuning effects. It is shown that blade assemblies with weak aerodynamic interblade coupling are highly sensitive to small blade mistuning, and that their dynamics is qualitatively altered in the following ways: the regular pattern that characterizes the root locus of the tuned aeroelastic eigenvalues in the complex plane is totally lost; the aeroelastic mode shapes become severely localized to only a few blades of the assembly and lose their constant interblade phase angle feature; curve veering phenomena take place when the eigenvalues are plotted versus a mistuning parameter.

Pierre, Christophe↗
NASA NTRS1990

Computation Of Flutter In Turbomachinery

"Direct" solution procedure supplants conventional eigenmode analysis. Iterative computational procedure yields critical mach number for onset of flutter and flutter angular frequency, of propfan, turbine with unshrouded blades, or other turbomachinery. Procedure applied to aeroelastic analysis of propfan, in which finite-element model of propfan structure combined with model of unsteady aerodynamics based on three-dimensional subsonic-lifting-surface theory. Particularly suitable for optimization in design because as optimal design evolves, flutter solution expected to change incrementally, so previous solution provides good estimates for start of current solution.

Murthy, Durbha V.↗