Engineering topics

NLN, Vipin

Publications and source records attributed to NLN, Vipin.

4 records

DOE OSTI2022

Volumetric nondestructive evaluation for damage in carbon fiber reinforced polymer panels subjected to artificial lightning strikes

Aircrafts and wind turbine blades often get hit by lightning strikes due to their operating locations. With increasing incidents of lightning flashes every year due to global warming, damage assessment of CFRP structures after lightning strike to aircrafts and wind turbine blades is getting increasingly important. Many researchers are involved in designing better and more resilient lighting strike protection materials and often utilize non-destructuve evaluation (NDE) methods such as ultrasonic testing (UT), high-speed digital videograpgy, and high-speed IR thermography. In particular, UT is widely used due to its cost-effectiveness compared to other methods. Using UT imaging can obtain any potential damaged locations caused by lightning strike through the thickness of the composite specimens. Traditional UT and visual inspections only display the damage in units area, when in fact the UT data is volumetric. This study optimized the UT data to measure and display the volumetric damage after artificial lightning strike and is compared to the standardized visual inspection.

Spencer, Ryan↗

DOE OSTI2021

Melt extruded versus extrusion compression molded glass-polypropylene long fiber thermoplastic composites

Long fiber thermoplastic (LFT) composites are processed either with extrusion compression or fiber injection processes. The properties of LFT materials are highly influenced by processing techniques, which lead to different porosity contents, fiber length distributions, and fiber orientation distributions. It is important to understand the various LFT processing techniques and their effects on mechanical, thermal, and microscopic properties. This work considered LFT sheets processed via extrusion, which offers highly aligned fibers (referred to as “Tecnogor composites”), and LFT composites produced via extrusion compression molding (ECM), which offers a random distribution of fibers. Tecnogor composites exhibited higher flexural strength (35–65%), flexural modulus (132–172%), tensile strength (39–52%), tensile modulus (67–75%), and Izod impact resistance (195–220%) than the random LFT composites. This response was attributed to the aligned fibers in Tecnogor composites. Mathematical models including Halpin-Tsai and Lavengood-Goettler were used to predict and compare the Young’s modulus of Tecnogor and ECM composites, respectively.

mechanical testing↗

DOE OSTI2020

High-performance molded composites using additively manufactured preforms with controlled fiber and pore morphology

Here, large-scale multimaterial preforms produced by additive manufacturing (AM) underwent compression molding (CM) to produce high-performance thermoplastic composites reinforced with short carbon fibers. AM and CM techniques were integrated to control the fiber orientation (microstructure) and to reduce void content for the improved mechanical performance of the composite. The new integrated manufacturing technique is termed “additive manufacturing-compression molding” (AM-CM). For the present study, the most common materials were used for large-scale printing, i.e., acrylonitrile butadiene styrene (ABS), carbon fiber (CF)–filled ABS (CF/ABS) and glass fiber (GF)–filled ABS (GF/ABS). Three different manufacturing processes; (a) AM (b) extrusion compression molding (ECM), and (c) AM-CM were used to prepare four different panel configurations: (1) neat ABS, (2) CF/ABS, (3) overmold (CF/ABS over neat ABS), and (4) sandwich (neat ABS between two CF/ABS layers). The mechanical properties (tensile and flexural strength and modulus, and Izod impact energy) of samples prepared via all three manufacturing processes were compared. X-ray microcomputer tomography was employed to evaluate the fiber orientation distribution and the volumetric porosity content. The preform maintained high fiber alignment (≈ 82% of fibers within the range of 0–20° in the deposition direction), and the volumetric porosity was reduced by 50% from 3.79% to 1.91% after compression. The alignment of long pores along the deposition direction was also observed. The mechanical properties are discussed with correlation to the fiber alignment and void content in the samples. CF/ABS samples prepared by AM-CM showed significant improvement of 11.15%, 35.27%, 28.6%, and 74.3% in the tensile strength, tensile modulus, flexural strength, and flexural modulus, respectively, when compared with samples prepared by ECM. Unique aspects of this study are the demonstration of large-scale multimaterial AM and the use of multimaterials as preforms to make high-performance composites.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Dual Material System for Polymer Large Scale Additive Manufacturing

Big Area Additive Manufacturing (BAAM) technology allows for manufacturing of large-scale objects with a potential to reduce energy embedded in products, reduce or eliminate energy necessary for transportation of goods along with reducing the lead time and cost in some cases. Over the last few years, Oak Ridge National Laboratory (ORNL) has been focusing on large-scale printing of single material systems, typically un-reinforced or short fiber reinforced polymers, in order to address needs in stiffness-limited applications. This paper describes the development of a multi-material large-scale AM system through a collaboration with Cincinnati Inc. and Performance Feed Screw Inc. Modifications to the Big Area Additive Manufacturing (BAAM) system includes a new extruder design to accommodate a dual feed system, an expanded two-dryer system with a capacity of 273 kg/dryer, and a system that is capable of mixing pelletized materials up to 60Kg/hr. This article highlights the advantages and limitations of the multi-material system as well as potential applications.

Smith, Tyler↗