Search NASA⌕ Search

Engineering topics

Nagamatsu, H. T.

Publications and source records attributed to Nagamatsu, H. T..

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

Calculation of scramjet inlet with thick boundary-layer ingestion

Numerical flowfields around a scramjet inlet model are simulated and analyzed. The present inlet flowfield is characterized by thick boundary-layer ingestion and strong viscous/inviscid interaction because of a combined effect of high hypersonic freestream Mach and low Reynolds numbers. Shock-induced separation further enlarges regions of viscous flows which occupy most of the inlet flowfield. Results obtained from the computations with the PARC code developed for ideal gas are presented for several 2D cases at various hypersonic Mach numbers ranging from 10 to 25, and two 3D simulations at Mach numbers of 12 and 19 are also discussed. Comparison between computation and experiment is made in terms of pressure distributions at the wall center line. Large discrepancy is observed and may be partially attributed to the lack of real gas and/or 3D effects in the simulation as well as to the uncertainty of the experiment.

Lai, H. T.↗
NASA NTRS1992

Numerical study of low-current steady arcs

The development of a high-efficiency CW YLF laser doped with Er,Tm,Ho: and featuring a strongly focusing resonator that collects a high density of pump power on the active crystal is described. The emission is investigated at 2.06 microns and a tuning range both at liquid-nitrogen (77 K) and at dry-ice (210 K) temperature. The noise characteristics and the long-term power stability of the laser is studied with an eye to employing this source for high-resolution spectroscopy in the 2-micron wavelength region. The detection of several absorption lines of NH3 at low pressure is described. The output power of the laser as a function of the power impinging on the crystal for different transmission of the output mirror is illustrated. The best result obtained is 1.46 W output for 3.2 W of argon pump. The minimum threshold achieved is 3.5 mW with a 1-percent transmission mirror. It is concluded that it is possible to develop a highly efficient Ho:YLF laser featuring low noise and sufficient tunability for high-resolution spectroscopy in the 2-micron region.

Kim, S. C.↗
NASA NTRS1992

Comparison between computational and experimental data for a hypersonic laser propelled vehicle

A 3-D axisymmetric hypersonic engine inlet was investigated using PARC2D, an ideal gas Computational Fluid Dynamics code. The code was used to predict the results of tests conducted in the Rensselaer Polytechnic Institute Hypersonic Shock Tunnel which measured surface and pitot pressures, and shock positions (through Schlieren photography) at freestream Mach numbers of 10, 13, and 15. A strong viscous/shock interaction was observed in both the experiment and the CFD results, due to the model's parabolic compression ramp. Good agreement was found between the experimental results and the CFD solution both for surface pressures and shock positions. Agreement between pitot pressures was less reliable.

Messitt, D. G.↗
NASA NTRS1991

Experimental investigation of a unique airbreathing pulsed laser propulsion concept

Investigations were conducted into unique methods of converting pulsed laser energy into propulsive thrust across a flat impulse surface under atmospheric conditions. The propulsion experiments were performed with a 1-micron neodymium-glass laser at the Space Plasma Branch of the Naval Research Laboratory. Laser-induced impulse was measured dynamically by ballistic pendulums and statically using piezoelectric pressure transducers on a stationary impulse surface. The principal goal was to explore methods for increasing the impulse coupling performance of airbreathing laser-propulsion engines. A magnetohydrodynamic thrust augmentation effect was discovered when a tesla-level magnetic field was applied perpendicular to the impulse surface. The impulse coupling coefficient performance doubled and continued to improve with increasing laser-pulse energies. The resultant performance of 180 to 200 N-s/MJ was found to be comparable to that of the earliest afterburning turbojets.

Myrabo, L. N.↗
NASA NTRS1990

Nature of convection-stabilized dc arcs in dual-flow nozzle geometry. I - The cold flow field and dc arc characteristics. II - Optical diagnostics and theory

Steady-state low-current air arcs in a dual-flow nozzle system are studied experimentally. The cold flow field with no arc is investigated using a 12.7-mm diameter dual-flow nozzle in a steady-flow facility. Mach number and mass flux distributions are determined for various nozzle-pressure ratios and nozzle-gap spacing. It is found that the shock waves in the converging-diverging nozzles result in a decrease in overal resistance by about 15 percent. Also, Schlieren and differential interferometry techniques are used to visualize the density gradients within the arc plasma and thermal mantle. Both optical techniques reveal a laminar arc structure for a reservoir pressure of 1 atm at various current levels. Experimentally determined axial static pressure and cold-flow mass flux rate distributions and a channel-flow model with constant arc temperatre are used to solve the energy integral for the arc radius as a function of axial distance. The arc electric field strength, voltage, resistance, and power are determined with Ohm's law and the total heat transfer is related to arc power.

Serbetci, Ilter↗
NASA NTRS1987

Endwall heat transfer in the junction region of a circular cylinder normal to a flat plate at 30 and 60 degrees from stagnation point of the cylinder

The objective of this experimental study was to investigate the influence of horseshoe vortex on the heat transfer on a flat plate near the base of a protruding cylinder. The partial shock reflection technique was used to produce the flow Mach number of 0.14 which simulated the mean inlet flow Mach number for the first stage vanes of the turbine after combustor. Fast response thin-film platinum heat gages were used to measure the heat transfer flux for radial distances of 0.75, 0.875, 1.0, 1.125 cylinder diameter. For a low Reynolds number of 20,000, r/D = 0.75, and angular location from the stagnation point = 60 deg, the maximum increase in the heat transfer rate with the cylinder was observed to be approximately 460 percent greater than without the cylinder. On the other hand, the increase in the heat flux for a high Reynolds number of 300,000 was approximately 70 percent greater. For the heat gages located along 30 deg and 60 deg angular locations from the stagnation point, the strong effect of the horseshoe vortex was observed in the junction region. The increase in the heat transfer rate depended on the type of boundary layer and on the boundary layer thickness ahead of the cylinder.

Nagamatsu, H. T.↗
NASA NTRS1986

Heat transfer in the stagnation region of the junction of a circular cylinder perpendicular to a flat plate

The heat transfer rate in the stagnation region of the junction of a circular cylinder perpendicular to a flat plate was measured for a range of Reynolds numbers varying from 3.0 x 10 to the 4th to 7.0 x 10 to the 5th and a flow Mach number of 0.14. The measurements were performed in a shock-tube facility using a reflected shockwave technique and thin-film platinum heat gages. The heat flux was measured for both the plate and the circular cylinder. A substantial increase in the heat transfer rate in the junction region was observed. The influence of the cylinder over the flat plate extended beyond 3/4 cylinder diameter for low Reynolds numbers. For high Reynolds numbers the maximum increase in the heat transfer rate was observed to be approximately 100 percent, but for very low Reynolds numbers a maximum increase in the heat flux to the plate by a factor of 5 was observed. The variations in the heat transfer rate to the stagnation point of the cylinder was very small.

Hinckel, J. N.↗
NASA NTRS1986

Relaminarization of the boundary layer over a flat plate in shock tube experiments

The relaminarization of the boundary layer over a flat plate in the shock tube was investigated by using the partially reflected shock wave technique. The flow Mach number was approximately 0.14, which corresponds to the inleft flow Mach number for the first row of vanes in a gas turbine. The thin film platinum heat gauges were used to measure the heat transfer rate and the Stanton number was calculated from the oscilloscope voltage traces. The Reynolds number was varied by changing the operation pressure of the shock tube and the values varied from 2.3 x 10 to the 4th to 5.3 x 10 to the 5th. For a Reynolds number range of 7 x 10 to the 4th to 3.5 x 10 to the 5th, the relaminarization of the boundary layer was observed. This phenomenon is due to the decay of the turbulence level in the flow as the reflected shock wave moves upstream from the flat plate. As the Reynolds number increased, the relaminarization was delayed and the delay was related to the turbulence generated by the reflected shock wave.

Hinckel, J. N.↗
NASA NTRS1986

Compressible laminar boundary layer with real gas effects for flight conditions to M(e) = 8 and T(o) = 2500 K

One of the problems for the hypersonic flights is the lack of accurate methods for predicting the boundary layer parameters at high Mach numbers and temperatures. At high Mach numbers and temperatures, the real gas effects should be included in calculations of the compressible laminar and turbulent boundary layers. By introducing the Mangler-Levy-Lees transformation, the compressible laminar boundary layer equations were transformed into two ordinary differential equations. To solve these ordinary differential equations for the flow over a flat plate, the Runge-Kutta method of order 5 and 6 was used with a secant method of solving the simultaneous nonlinear equations for the boundary layer conditions. Instead of using the perfect gas assumptions, the properties of air in the temperature range of 100 to 2500 K at M(e) = 8 were used for the calculations. The calculations were carried out for free flight conditions. The real gas effects were significant for the conditions of high freestream Mach numbers, and the boundary layer parameters from the real gas solutions were quite different from the existing formulas and solutions.

Nagamatsu, H. T.↗
NASA NTRS1985

Experimental observation of transition behavior on a flat plate

In studying transition behavior a shock tube and tunnel were used to produce high temperatures, and thin-film platinum heat gauges were used to measure local heat flux as well as to detect the transition of the laminar boundary layer over a flat plate and a cone. Initial investigations were conducted in the hypersonic shock tunnel to obtain high-temperature information for the development of an ICBM nose cone. Shock Mach numbers as large as 50 with a temperature of 15,000 K after the incident wave were produced in the driven tube. Shock tubes are used to investigate the heat transfer over various surfaces to 2500 K for the development of future gas turbines.

Nagamatsu, H. T.↗
NASA NTRS1985

Supercritical airfoil drag reduction by passive shock wave/boundary layer control in the Mach number range .75 to .90

Airfoils operating in the transonic region are subject to large increases in drag due to shock wave/boundary layer interactions. The concept of passive shock wave/boundary layer control seeks drag reduction by placing a thin cavity with a porous top surface at the airfoil chordwise position where a shock wave would normally occur. The higher pressure behind the shock wave circulates flow through the cavity to the lower pressure ahead of the shock wave. The effects from this circulation prevent boundary layer separation and reduce entropy increases through the shock wave. In this investigation this concept is studied at a freestream Mach number range of .75 and .90. The Mach number distributions over the model, the wake impact pressure surveys used to determine profile drag and schlieren photographs for 2.8 percent porosity and solid airfoil cases are presented and compared. Results indicate that the profile drag coefficient can be reduced by as much as 40 percent through the use of this passive drag control system.

Nagamatsu, H. T.↗
NASA NTRS1984

Investigation to optimize the passive shock wave/boundary layer control for supercritical airfoil drag reduction

The passive shock wave/boundary layer control for reducing the drag of 14%-thick supercritical airfoil was investigated in the 3 in. x 15.4 in. RPI Transonic Wind Tunnel with and without the top wall insert at transonic Mach numbers. Top wall insert was installed to increase the flow Mach number to 0.90 with the model mounted on the test section bottom wall. Various porous surfaces with a cavity underneath were positioned on the area of the airfoil where the shock wave occurs. The higher pressure behind the shock wave circulates flow through the cavity to the lower pressure ahead of the shock wave. The effects from this circulation prevent boundary layer separation and enthropy increase hrough the shock wave. The static pressure distributions over the airfoil, the wake impact pressure survey for determining the profile drag and the Schlieren photographs for porous surfaces are presented and compared with the results for solid surface airfoil. With a 2.8% uniform porosity the normal shock wave for the solid surface was changed to a lambda shock wave, and the wake impact pressure data indicate a drag coefficient reduction as much as 45% lower than for the solid surface airfoil at high transonic Mach numbers.

Nagamatsu, H. T.↗
NASA NTRS1984

Heat transfer investigation in the junction region of circular cylinder normal to a flat plate at 90 deg location

External heat-transfer rates were measured on a flat plate in the junction region of a circular cylinder mounted normal to the plate at a location 90 deg from the stagnation point. This configuration simulates the junction of the shroud with gas-turbine vanes. Heat-transfer results are presented for laminar, transition, and turbulent boundary layers for a Mach number of 0.14 with gas temperatures of approximately 750 deg R over a flat plate at room temperature. The measurements were made in air for a unit Reynolds number, Re/cm, range of 11,000 to 58,000. Heat-transfer measurements were conducted in the 70-ft long, 4-in. diameter shock tube. A shock-wave reflection technique was used to produce a flow Mach number of 0.14. Thin-film platinum heat gages were mounted on the flat plate and along the line of the stagnation point of the cylinder to measure the local heat flux in the junction region. The experimental heat-transfer data were correlated with the laminar and turbulent boundary-layer theories for the flat plate. With the cylinder the heat fluxes on the flat plate were greatly increased in the junction region compared to the heat flux for the plate alone.

Nagamatsu, H. T.↗
NASA NTRS1984

Convective heat transfer studies at high temperatures with pressure gradient for inlet flow Mach number of 0.45

Heat transfer measurements were determined for a flat plate with and without pressure gradient for various free stream temperatures, wall temperature ratios, and Reynolds numbers for an inlet flow Mach number of 0.45, which is a representative inlet Mach number for gas turbine rotor blades. A shock tube generated the high temperature and pressure air flow, and a variable geometry test section was used to produce inlet flow Mach number of 0.45 and accelerate the flow over the plate to sonic velocity. Thin-film platinum heat gages recorded the local heat flux for laminar, transition, and turbulent boundary layers. The free stream temperatures varied from 611 R (339 K) to 3840 R (2133 K) for a T(w)/T(r,g) temperature ratio of 0.87 to 0.14. The Reynolds number over the heat gages varied from 3000 to 690,000. The experimental heat transfer data were correlated with laminar and turbulent boundary layer theories for the range of temperatures and Reynolds numbers and the transition phenomenon was examined.

Pedrosa, A. C. F.↗
NASA NTRS1984

Flat plate heat transfer for laminar transition and turbulent boundary layers using a shock tube

Heat transfer results are presented for laminar, transition, and turbulent boundary layers for a Mach number of 0.12 with gas temperatures of 425 K and 1000 K over a flat plate at room temperature. The measurements were made in air for a Reynolds number range of 600 to 6 million. The heat transfer measurements were conducted in a 70-ft long, 4 in. diameter shock tube. Reflecting wedges were used to reflect the incident shock wave to produce a flow Mach number of 0.12 behind the reflected shock wave. Thin film platinum heat gages were mounted on the plate surface to measure the local heat flux. The laminar results for gas temperatures of 425 K to 1000 K agree well with theory. The turbulent results are also close to incompressible theory, with the 1000 K flow case being slightly higher. The transition results lie between the laminar and turbulent predictions.

Brostmeyer, J. D.↗
NASA NTRS1984

Porosity effect on supercritical airfoil drag reduction by shock wave/boundary layer control

An investigation of the passive shock wave/boundary layer control for reducing the drag of 14 percent-thick supercritical airfoil was conducted in the 3 in. x 15.4 in. RPI Transonic Wind Tunnel at transonic Mach numbers. Various porous surfaces with a cavity beneath it was positioned on the area of the airfoil, mounted on the test section bottom wall, where the shock wave occurs. The static pressure distributions over the airfoil, the wake impact pressure survey for determining the profile drag and the Schlieren photographs for porous surfaces are presented and compared with the results for solid surface airfoil. With a uniform porosity surface the normal shock wave for solid surface was changed to a lambda shock wave, and the wake impact pressure data indicated an appreciable drag reduction at transonic Mach numbers. For a free stream Mach number of 0.81 the profile drag coefficient for the airfoil top surface with uniform porosity was 46 percent lower than for the solid surface airfoil.

Nagamatsu, H. T.↗
NASA NTRS1984

Investigation of the effects of pressure gradient, temperature and wall temperature ratio on the stagnation point heat transfer for circular cylinders and gas turbine vanes

Low and high pressure shock tubes were designed and constructed for the purpose of obtaining heat transfer data over a temperature range of 390 to 2500 K, pressures of 0.3 to 42 atm, and Mach numbers of 0.15 to 1.5 with and without pressure gradient. A square test section with adjustable top and bottom walls was constructed to produce the favorable and adverse pressure gradient over the flat plate with heat gages. A water cooled gas turbine nozzle cascade which is attached to the high pressure shock tube was obtained to measuse the heat flux over pressure and suction surfaces. Thin-film platinum heat gages with a response time of a few microseconds were developed and used to measure the heat flux for laminar, transition, and turbulent boundary layers. The laminar boundary heat flux on the shock tube wall agreed with Mirel's flat plate theory. Stagnation point heat transfer for circular cylinders at low temperature compared with the theoretical prediction, but for a gas temperature of 922 K the heat fluxes were higher than the predicted values. Preliminary flat plate heat transfer data were measured for laminar, transition, and turbulent boundary layers with and without pressure gradients for free-stream temperatures of 350 to 2575 K and flow Mach numbers of 0.11 to 1.9. The experimental heat flux data were correlated with the laminar and turbulent theories and the agreement was good at low temperatures which was not the case for higher temperatures.

Nagamatsu, H. T.↗