Engineering topics
Narayan, Sri R.
Publications and source records attributed to Narayan, Sri R..
Rapid and Reversible Lithium Insertion in the Wadsley–Roth-Derived Phase NaNb 13 O 33
Not Available
Room-Temperature Electrochemical Fluoride (De)insertion into CsMnFeF[subscript 6]
Explore the source record for details and available documents.
Promoting Reversibility of Multielectron Redox in Alkali-Rich Sulfide Cathodes through Cryomilling
We report conventional cathodes for Li-ion batteries (LIBs) are reaching their theoretical capacity limits. One way to meet the growing demands for high-capacity LIBs is by developing so-called Li-rich cathode materials that greatly benefit from additional capacities from anionic moieties in the structure. Li-rich materials are intrinsically subject to higher degrees of (de)intercalation, leaving the particles more prone to fractures and thus rapid capacity fade. Alkali-rich LiNaFeS 2 reversibly cycles with capacities exceeding 300 mAh g -1 , but its capacity fades faster than an isostructural material Li 2 FeS 2 . Using synchrotron-based transmission X-ray microscopy (TXM), we demonstrate that the capacity fade of LiNaFeS 2 stems from particle fractures in the first charge cycle. We improve the cycling performance of LiNaFeS 2 by means of cryomilling, which enhances capacity retention at cycle 50 by 76%. Through crystallographic and morphological characterization techniques, we confirm that cryomilling not only decreases particle and crystallite size while increasing microstrain but also prevents particles from fracturing. Cryomilling is a powerful tool to engineer nanoscale battery materials, and TXM allows the direct observation of morphological changes of the particles, which can be leveraged to develop next-generation cathode materials for LIBs.
Stable positive side material for all-organic flow battery
A quinone derivative with a high redox potential that does not undergo Michael addition or proto-desulfonation. This molecule addresses the key issues faced with the positive side material of an aqueous all-organic flow battery. This new molecule is 2,5-dihydroxy-4,6-dimethylbenzene-1,3-disulfonic acid (or the disulfonate salt thereof). This quinone derivative offers good solubility, electrochemical reversibility, and robustness to charge/discharge cycling. Quinones with reduced crossover are also provided.
Electrochemical Oxidative Fluorination of an Oxide Perovskite
Explore the source record for details and available documents.
Controlling Covalency and Anion Redox Potentials through Anion Substitution in Li-Rich Chalcogenides
Development of next-generation battery technologies is imperative in the pursuit of a clean energy future. Toward that end, battery chemistries capable of multielectron redox processes are at the forefront of studies on Li-based systems to increase the gravimetric capacity of the cathode. Multielectron processes rely either on the iterative redox of transition metal cations or redox involving both the transition metal cations and the anionic framework. Targeting coupled cation and anion redox to achieve multielectron charge storage is difficult, however, because the structure–property relationships that govern reversibility are poorly understood. In an effort to develop fundamental understanding of anion redox, we have developed a materials family that displays tunable anion redox over a range of potentials that are dependent on a systematic modification of the stoichiometry. We report anion redox in the chalcogenide solid solution Li 2 FeS 2–y Se y , wherein the mixing of the sulfide and selenide anions yields a controllable shift in the high voltage oxidation plateau. Electrochemical measurements indicate that reversible multielectron redox occurs across the solid solution. X-ray absorption spectroscopy supports the oxidation of both iron and selenium at high states of charge, while Raman spectroscopy indicates the formation of Se–Se dimers in Li 2 FeSe 2 upon Li deintercalation, providing insight into the charge mechanism of the Li-rich iron chalcogenides. Anion substitution presents direct control over the functional properties of multielectron redox materials for next generation battery technologies.
Materials for high-performance aqueous organic redox flow batteries
Quinones and related compounds for use in flow batteries are provided. Many of these compounds are found to mitigate the effects of crossover in a flow battery. Other structure for improving battery performance is provided.
Nanostructured Platinum Alloys for Use as Catalyst Materials
A series of binary and ternary Pt-alloys, that promote the important reactions for catalysis at an alloy surface; oxygen reduction, hydrogen oxidation, and hydrogen and oxygen evolution. The first two of these reactions are essential when applying the alloy for use in a PEMFC.
Iron-Air Rechargeable Battery
Embodiments include an iron-air rechargeable battery having a composite electrode including an iron electrode and a hydrogen electrode integrated therewith. An air electrode is spaced from the iron electrode and an electrolyte is provided in contact with the air electrode and the iron electrodes. Various additives and catalysts are disclosed with respect to the iron electrode, air electrode, and electrolyte for increasing battery efficiency and cycle life.
Nanostructured Platinum Alloys for Use as Catalyst Materials
A series of binary and ternary Pt-alloys, that promote the important reactions for catalysis at an alloy surface; oxygen reduction, hydrogen oxidation, and hydrogen and oxygen evolution. The first two of these reactions are essential when applying the alloy for use in a PEMFC.
Pt-Ni and Pt-Co Catalyst Synthesis Route for Fuel Cell Applications
Oxygen reduction reactions (ORRs) at the cathode are the rate-limiting step in fuel cell performance. The ORR is 100 times slower than the corresponding hydrogen oxidation at the anode. Speeding up the reaction at the cathode will improve fuel cell efficiency. The cathode material is generally Pt powder painted onto a substrate (e.g., graphite paper). Recent efforts in the fuel cell area have focused on replacing Pt with Pt-X alloys (where X = Co, Ni, Zr, etc.) in order to (a) reduce cost, and (b) increase ORR rates. One of these strategies is to increase ORR rates by reducing the powder size, which would result in an increase in the surface area, thereby facilitating faster reaction rates. In this work, a process has been developed that creates Pt-Ni or Pt-Co alloys that are finely divided (on the nano scale) and provide equivalent performance at lower Pt loadings. Lower Pt loadings will translate to lower cost. Precursor salts of the metals are dissolved in water and mixed. Next, the salt mixtures are dried on a hot plate. Finally, the dried salt mixture is heattreated in a furnace under flowing reducing gas. The catalyst powder is then used to fabricate a membrane electrode assembly (MEA) for electrochemical performance testing. The Pt- Co catalyst-based MEA showed comparable performance to an MEA fabri cated using a standard Pt black fuel cell catalyst. The main objective of this program has been to increase the overall efficiencies of fuel cell systems to support power for manned lunar bases. This work may also have an impact on terrestrial programs, possibly to support the effort to develop a carbon-free energy source. This catalyst can be used to fabricate high-efficiency fuel cell units that can be used in space as regenerative fuel cell systems, and terrestrially as primary fuel cells. Terrestrially, this technology will become increasingly important when transition to a hydrogen economy occurs.
Imidazolium-Based Polymeric Materials as Alkaline Anion-Exchange Fuel Cell Membranes
Polymer electrolyte membranes that conduct hydroxide ions have potential use in fuel cells. A variety of polystyrene-based quaternary ammonium hydroxides have been reported as anion exchange fuel cell membranes. However, the hydrolytic stability and conductivity of the commercially available membranes are not adequate to meet the requirements of fuel cell applications. When compared with commercially available membranes, polystyrene-imidazolium alkaline membrane electrolytes are more stable and more highly conducting. At the time of this reporting, this has been the first such usage for imidazolium-based polymeric materials for fuel cells. Imidazolium salts are known to be electrochemically stable over wide potential ranges. By controlling the relative ratio of imidazolium groups in polystyrene-imidazolium salts, their physiochemical properties could be modulated. Alkaline anion exchange membranes based on polystyrene-imidazolium hydroxide materials have been developed. The first step was to synthesize the poly(styrene-co-(1-((4-vinyl)methyl)-3- methylimidazolium) chloride through a free-radical polymerization. Casting of this material followed by in situ treatment of the membranes with sodium hydroxide solutions provided the corresponding hydroxide salts. Various ratios of the monomers 4-chloromoethylvinylbenzine (CMVB) and vinylbenzine (VB) provided various compositions of the polymer. The preferred material, due to the relative ease of casting the film, and its relatively low hygroscopic nature, was a 2:1 ratio of CMVB to VB. Testing confirmed that at room temperature, the new membranes outperformed commercially available membranes by a large margin. With fuel cells now in use at NASA and in transportation, and with defense potential, any improvement to fuel cell efficiency is a significant development.
Iridium-Doped Ruthenium Oxide Catalyst for Oxygen Evolution
NASA requires a durable and efficient catalyst for the electrolysis of water in a polymer-electrolyte-membrane (PEM) cell. Ruthenium oxide in a slightly reduced form is known to be a very efficient catalyst for the anodic oxidation of water to oxygen, but it degrades rapidly, reducing efficiency. To combat this tendency of ruthenium oxide to change oxidation states, it is combined with iridium, which has a tendency to stabilize ruthenium oxide at oxygen evolution potentials. The novel oxygen evolution catalyst was fabricated under flowing argon in order to allow the iridium to preferentially react with oxygen from the ruthenium oxide, and not oxygen from the environment. Nanoparticulate iridium black and anhydrous ruthenium oxide are weighed out and mixed to 5 18 atomic percent. They are then heat treated at 300 C under flowing argon (in order to create an inert environment) for a minimum of 14 hours. This temperature was chosen because it is approximately the creep temperature of ruthenium oxide, and is below the sintering temperature of both materials. In general, the temperature should always be below the sintering temperature of both materials. The iridium- doped ruthenium oxide catalyst is then fabricated into a PEM-based membrane- electrode assembly (MEA), and then mounted into test cells. The result is an electrolyzer system that can sustain electrolysis at twice the current density, and at the same efficiency as commercial catalysts in the range of 100-200 mA/sq cm. At 200 mA/sq cm, this new system operates at an efficiency of 85 percent, which is 2 percent greater than commercially available catalysts. Testing has shown that this material is as stable as commercially available oxygen evolution catalysts. This means that this new catalyst can be used to regenerate fuel cell systems in space, and as a hydrogen generator on Earth.