Engineering topics

Nazeeruddin, Mohammad Khaja

Publications and source records attributed to Nazeeruddin, Mohammad Khaja.

8 records

DOE OSTI2024

A thermotropic liquid crystal enables efficient and stable perovskite solar modules

Perovskite solar cells have seen impressive progress in performance and stability, yet maintaining efficiency while scaling area remains a challenge. Here we find that additives commonly used to passivate large-area perovskite films often co-precipitate during perovskite crystallization and aggregate at interfaces, contributing to defects and to spatial inhomogeneity. Here we develop design criteria for additives to prevent their evaporative precipitation and enable uniform passivation of defects. We explored liquid crystals with melting point below the perovskite processing temperature, functionalization for defect passivation and hydrophobicity to improve device stability. We find that thermotropic liquid crystals such as 3,4,5-trifluoro-4'-(trans-4-propylcyclohexyl)biphenyl enable large-area perovskite films that are uniform, low in defects and stable against environmental stress factors. We demonstrate modules with a certified stabilized efficiency of 21.1% at an aperture area of 31 cm 2 and enhanced stability under damp-heat conditions (ISOS-D-3, 85% relative humidity, 85 °C) with T 86 (the duration for the efficiency to decay to 86% of the initial value) of 1,200 h, and reverse bias with (ISOS-V-1, negative maximum-power-point voltage) and without bypass diodes.

14 SOLAR ENERGY↗

DOE OSTI2023

Oriented nucleation in formamidinium perovskite for photovoltaics

The black phase of formamidinium lead iodide (FAPbI 3 ) perovskite shows huge promise as an efficient photovoltaic, but it is not favoured energetically at room temperature, meaning that the undesirable yellow phases are always present alongside it during crystallization. This problem has made it difficult to formulate the fast crystallization process of perovskite and develop guidelines governing the formation of black-phase FAPbI 3 . Here, we use in situ monitoring of the perovskite crystallization process to report an oriented nucleation mechanism that can help to avoid the presence of undesirable phases and improve the performance of photovoltaic devices in different film-processing scenarios. The resulting device has a demonstrated power-conversion efficiency of 25.4% (certified 25.0%) and the module, which has an area of 27.83 cm 2 , has achieved an impressive certified aperture efficiency of 21.4%.

14 SOLAR ENERGY↗

DOE OSTI2023

Co-deposition of hole-selective contact and absorber for improving the processability of perovskite solar cells

Simplifying the manufacturing processes of renewable energy technologies is crucial to lowering the barriers to commercialization. In this context, to improve the manufacturability of perovskite solar cells (PSCs), here we have developed a one-step solution-coating procedure in which the hole-selective contact and perovskite light absorber spontaneously form, resulting in efficient inverted PSCs. We observed that phosphonic or carboxylic acids, incorporated into perovskite precursor solutions, self-assemble on the indium tin oxide substrate during perovskite film processing. They form a robust self-assembled monolayer as an excellent hole-selective contact while the perovskite crystallizes. Our approach solves wettability issues and simplifies device fabrication, advancing the manufacturability of PSCs. Our PSC devices with positive-intrinsic-negative (p-i-n) geometry show a power conversion efficiency of 24.5% and retain >90% of their initial efficiency after 1,200 h of operating at the maximum power point under continuous illumination. The approach shows good generality as it is compatible with different self-assembled monolayer molecular systems, perovskites, solvents and processing methods.

14 SOLAR ENERGY↗

DOE OSTI2022

Tailoring electric dipole of hole-transporting material p-dopants for perovskite solar cells

We report Li-TFSI/t-BP are the most widely employed p-dopants for hole-transporting materials (HTMs) within the state-of-the-art perovskite solar cells (PSCs). The hygroscopicity and migration of these dopants, however, lead to devices with limited stability. To solve this problem, we report here on a diphenyl iodide cation and pentafluorophenyl boric acid anion-based dopant (DIC-PBA) with an oriented interfacial dipole moment as an alternative to Li-TFSI/t-BP. Theoretical and experimental data reveal that DIC-PBA exhibits deep doping of poly[bis(4-phenyl)(2,4,6-triMethylphenyl)aMine] (PTAA) and also creates p-doping of perovskite surface, which originates from ionic interactions-derived dipole arrangement that yields fast interfacial charge transport. The improved intrinsic stability of PSCs originates from the inhibition of dipole moment degeneration on the perovskite surface. Devices prepared with DIC-PBA yielded high efficiency of 22.86%, and the modules (aperture area: 33.2 cm 2 ) efficiency reached 19.13%. Importantly, the storage stability also significantly improved exceeding to 90% after aging 1,200 h under air ambient.

14 SOLAR ENERGY↗

DOE OSTI2022

Area-Scalable Zn 2 SnO 4 Electron Transport Layer for Highly Efficient and Stable Perovskite Solar Modules

The development of a scalable chemical bath deposition (CBD) process facilitates the realization of electron-transporting layers (ETLs) for large-area perovskite solar modules (PSMs). In this work, a method to prepare a uniform and scalable thick Zn 2 SnO 4 ETL by CBD, which yielded high-performance PSMs, is reported. This Zn 2 SnO 4 ETL exhibits excellent electrical properties and enhanced optical transmittance in the visible region. Moreover, the Zn 2 SnO 4 ETL influences the perovskite layer formation, yielding enhanced crystallinity, increased grain size, and a smoother surface, thus facilitating electron extraction and collection from the perovskite to the ETL. Zn 2 SnO 4 thereby yields PSMs with a remarkable photovoltaic performance, low hysteresis index, and high device reproducibility. The champion PSM exhibited a power conversion efficiency (PCE) of 22.59%, being among the highest values published so far. In addition, the CBD Zn 2 SnO 4 -based PSMs exhibit high stability, retaining more than 88% of initial efficiency over 1000 h under continuous illumination. This demonstrates that CBD Zn 2 SnO 4 is an appropriate ETL for high-efficiency PSMs and a viable new process for their industrialization.

17 WIND ENERGY↗

DOE OSTI2021

High-efficiency perovskite photovoltaic modules achieved via cesium doping

Perovskite solar modules have been attracting increasing attention due to their market potential, yet publications concerned with theintrinsic scale-up potential of different perovskite compositions remain relatively scarce. On the other hand, while great success is being made towards improving the power conversion efficiency (PCE) of perovskite solar cells (PSCs) by cesium cation (Cs + ) doping of the perovskite, more attention is being paid to the perovskite phase stabilization effect of Cs + doping, and less to other properties that are critical to understand and futher improve the PSC's. In this work, moderately-Cs-doped MAPbI 3 was employed as a model perovskite material in order to exclude the phase stabilization effect. Our systematic study revealed the influence of Cs + in organic-inorganic hybrid perovskites on the crystal structure, crystallization process, trap state density, band structure and charge (i.e., ions or photo-carriers) transport. Markedly, it has been observed that Cs + doping can greatly increase the carrier diffusion length in the perovskite films, thus improving the potential to scale-up PSC's.The PCE of small area devices (0.09 cm 2 ) was increased to 21.72% from 19.73%, with decreased hysteresis behavior and increased operational stability (T85 = 1000 h) after Cs + doped, where T85 refers to the retention of 85% of the initial PCE. Moreover, a PCE of 21.08% was obtained for a Cs + -containing perovskite module with an active area > 30 cm 2 , which demonstrates a better "reproducibility" than the reference sample (MAPbI3-based perovskite modules, PCE = 18.26%).

14 SOLAR ENERGY↗

DOE OSTI2021

Observation of large Rashba spin–orbit coupling at room temperature in compositionally engineered perovskite single crystals and application in high performance photodetectors

Indirect absorption extended below the direct transition edge and increase in carrier lifetime derived from Rashba spin–orbit coupling may advance the optoelectronic applications of metal halide perovskites. Spin-orbit coupling in halide perovskites is due to the presence of heavy elements in their structure. However, when these materials lack an inversion symmetry, for example by the application of strain, spin–orbit coupling becomes odd in the electron’s momentum giving rise to a splitting in the electronic energy bands. Here we report on the observation of a large Rashba splitting of 117 meV at room temperature, as predicted by relativistic first-principles calculations, in halide perovskite single crystals through a facile compositional engineering approach. Partial substitution of organic cations by rubidium in single crystals induces significant indirect absorption and dual peak photoluminescence as a result of a large Rashba splitting. We measured circularly polarized photoluminescence and magneto-photoluminescence in perovskite films printed by single crystals as well as magneto-electroluminescence and magneto-photocurrent in spin-LEDs based on perovskite single crystals. They indicated significant spin-momentum locking due to the large Rashba effect. A hybrid perovskite single crystal photodetector achieved record figures of merit, including detectivity of more than 1.3 × 10 18 Jones which represents a three orders of magnitude improvement compared to the to date record. Furthermore, these findings show that facile compositional engineering of perovskite single crystals holds great promise for further advancing the optoelectronic properties of existing materials.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Consensus statement for stability assessment and reporting for perovskite photovoltaics based on ISOS procedures

Improving the long-term stability of perovskite solar cells is critical to the deployment of this technology. Despite the great emphasis laid on stability-related investigations, publications lack consistency in experimental procedures and parameters reported. It is therefore challenging to reproduce and compare results and thereby develop a deep understanding of degradation mechanisms. Here, we report a consensus between researchers in the field on procedures for testing perovskite solar cell stability, which are based on the International Summit on Organic Photovoltaic Stability (ISOS) protocols. We propose additional procedures to account for properties specific to PSCs such as ion redistribution under electric fields, reversible degradation and to distinguish ambient-induced degradation from other stress factors. These protocols are not intended as a replacement of the existing qualification standards, but rather they aim to unify the stability assessment and to understand failure modes. Finally, we identify key procedural information which we suggest reporting in publications to improve reproducibility and enable large data set analysis.

14 SOLAR ENERGY↗