Search NASA⌕ Search

Engineering topics

Nelson, Andrew

Publications and source records attributed to Nelson, Andrew.

14 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Viability of Miniature Discs in LFA-427

Miniature disc samples pose challenging measuring conditions for laser flash analysis. With reductions in signal from lower radiosity and lower half-rise times from low thicknesses, optimal selections of coatings and laser parameters are critical in a successful measurement. This report explains the methodology in successfully measuring two different material types—metals and ceramics—in proper coating selection, laser parameters, and post analysis for each material, as well as applying it to un-irradiated uranium samples of each type (U-metal, UO 2 ). This was done through a combination of analysis techniques combining automatic commercial methods (Neztech) and manual methods for correcting laser pulse impact aberrations.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Interface stability of ultrasonic additively manufactured Zircaloy-4 during hydrothermal corrosion

Simulated pressurized water reactor conditions (330 °C, 15.6 MPa, ~20 ppb oxygen) without irradiation were used to investigate the hydrothermal corrosion behavior of ultrasonic additively manufactured Zircaloy-4 up to 1000 h. X-ray computed tomography allowed for visualization of defects from processing and their progression after corrosion experiments. The specimens were found to have clear variability in the mass change data, compared to typical wrought Zircaloy-4 specimens. The variation in the mass change after exposure was attributed to weld defects connected to the specimen surface which allowed ingress of oxidant into the samples. Defects visualized by computed tomography were found via metallography and characterized. In conclusion, ultrasonic additively manufactured Zircaloy-4 was found to have comparable corrosion behavior as wrought Zircaloy-4 for specimens which did not have clear surface defects along weld interfaces.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Post-Irradiation Fracture Toughness Characterization of Generation II FeCrAl Alloys

FeCrAl alloys are promising candidate materials for the accident tolerant fuel (ATF) cladding application due to their exceptional resistance to oxidation in elevated temperature steam environments. Currently, limited fracture toughness data are available for the FeCrAl alloys, including the FeCrAl alloys newly developed at Oak Ridge National Laboratory (ORNL) under the U.S. Department of Energy’s Advanced Fuels Campaign (AFC) program. In this study, two Generation II candidate FeCrAl alloys, i.e., C06M (81.8Fe-10Cr-6Al-0.03Y-2Mo-0.2Si) and C36M (78.8Fe-13Cr-6Al-0.03Y-2Mo-0.2Si), were irradiated in the High Flux Isotope Reactor (HFIR) at ORNL to assess the fracture characteristics of these alloys after neutron irradiation. A total of six rabbit capsules were irradiated in HFIR at target temperatures of 200°C, 330°C, and 500°C up to target damage doses of 8 displacements per atom (dpa) and 16 dpa. Post-irradiation fracture toughness testing was performed following the Master Curve method in the ASTM E1921 standard. The main findings of this study are:1) Both the C06M and C36M alloys exhibited a similar response to irradiation concerning irradiation hardening and embrittlement.2) The irradiation temperature played different roles in terms of irradiation hardening and embrittlement for both C06M and C36M: after irradiation between 166°C and 204°C, both materials exhibited significant irradiation hardening and embrittlement; after irradiation between 315°C and 343°C, both materials showed small irradiation hardening without irradiation embrittlement. After irradiation between 501°C and 507°C, however, the irradiation softening without irradiation embrittlement was observed in both materials.3) Comparing the microhardness and Master Curve reference temperature T0q before and after neutron irradiation, we did not observe a linear correlation between the two parameters for both C06M and C36M steels. This should be mainly due to a flat response of the Master Curve reference temperature T0q to the irradiations at 166–204°C and 315–343°C ranges4) C06M showed a lower T0q, meaning better toughness, than C36M at the unirradiated condition, and such trend was kept even after neutron irradiation except for the 166–204°C irradiation after which both materials had similar T0q.5) In terms of hardening and embrittlement, the irradiation effect on both C06M and C36M appeared to saturate after an irradiation dose of 7 dpa.

Chen, Xiang↗
DOE OSTI2022

Creep behavior of an additively manufactured 9Cr steel in the as-built condition

Limited studies have evaluated the creep behavior of additively manufactured (AM) ferritic-martensitic (FM) steels. This work investigated the creep behavior of a 9Cr FM steel fabricated by powder blown directed energy deposition (DED) technique. Here, the creep testing at 550–650 °C and 150 MPa for the specimens along the deposition direction in the as-built condition, together with corresponding microstructural characterization, revealed a threshold temperature between 600 and 625 °C, below which the steel has creep resistance comparable with Grade 91 cross-welds and noticeably greater than 9Cr-1Mo steel. The threshold temperature distinguishes the creep behavior in two regimes differentiated in creep activation energy, creep deformation, and failure mechanism. Unlike the creep rupture surface ~45° from the loading direction when tested above the threshold temperature, the creep rupture for testing below the threshold temperature resembles type IV failure in the cross-welds of ferritic steels. The DED-induced layer structure in the as-built steel played a significant role on the change of creep behavior.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Report summarizing demonstration of thermal conductivity measurement methods for coated zirconium cladding

Thermal diffusivity measurements on Zirconium-based cladding materials have historically been a challenge due to the difficulty to measure on specimens with curved geometries, including nuclear grade Zircaloy cladding materials. In this work, we first used Laser Flash Analysis methods to measure the thermal diffusivity of Zircaloy tubes, which show good agreement with Zircaloy plates in this work, as well as previously published data. The consistent results proved the applicability of the Laser Flash Analysis setup for investigating thermal diffusivity of Zircaloy tubes. We further investigate the hydrogen effect on thermal diffusivity of Zircaloy tubes. Hydrogen plays significant roles in temperature dependent thermal diffusivity trends of Zircaloy tube. For low hydrogen concentration, where hydride dissolved into single phase α-Zr at higher temperature, thermal diffusivity is relatively unchanged at low temperature at two phase regions (α-Zr and δ-hydride), and it increases as a function of temperature at single phase α-Zr region. For high hydrogen concentration, where phase transformation (α-Zr + δ-hydride → α-Zr + β-Zr) occurs at 567 °C, thermal diffusivity decreases as a function of temperature below 567 °C before the transformation (α-Zr and δ-hydride), while increase at higher temperature after the transformation (α-Zr and β-Zr).

36 MATERIALS SCIENCE↗
DOE OSTI2021

The U.S. Accident Tolerant Fuels Program — Update on a National Initiative

In 2012 the U.S. Congress directed the Department of Energy’s (DOE) Office of Nuclear Energy to give priority to developing enhanced fuels and cladding for light water reactors to improve safety in the event of accidents in the reactor or spent fuel pools. DOE developed a plan with a goal to insert a Lead Test Assembly (LTA) into a commercial light water reactor by the end of FY 2022. Three of the leading commercial nuclear fuel vendors, in concert with several participating commercial nuclear utilities, are now seriously engaged in this initiative and have exceeded initial expectations by having met DOE’s goal this year, three years ahead of schedule. The early successes of the ATF program are due in part to a strong collaboration by the DOE national laboratories with both commercial nuclear fuel vendors and the U.S. Nuclear Regulatory Commission. This undertaking has recently been expanded to incorporate an effort to extend burnup from the current U.S. regulatory limit of 62 GWD/MTU and increase enrichment as necessary to support routine utilization of fuel at >75 GWD/MTU. This effort provides a critical economic incentive to accelerate the deployment of ATF technologies. This paper reviews the DOE-sponsored, industry-led ATF concepts currently under development and highlights the contributions made by the DOE laboratories in support of these ATF concepts, including: 1) steady-state irradiation testing in the Advanced Test Reactor (ATR) and High Flux Isotope Reactor (HFIR); 2) transient irradiation testing in the Transient Reactor Test Facility (TREAT); 3) fabrication process development and characterization of high density fuels, Cr-coated Zry cladding, FeCrAl cladding, and SiC cladding; and 4) post-irradiation examination of lead test rods irradiated in commercial reactors.

Goldner, Frank J.↗
DOE OSTI2021

Impact of Coating Defects on Performance of Coated Zirconium Cladding

Research on accident tolerant fuels (ATF) has started after the Fukushima accident [1–3]. While efforts have been expended on both fuel and cladding ATF concepts, the bulk of work has been devoted to improved cladding. The overarching goal of these approaches is to extend the coping time available during a severe accident before any event would result in release of radioactivity to the public. The most basic ATF cladding concept is obtained by applying a thin coating of highly corrosion-resistant material on the surface of a licensed zirconium cladding alloy. This thin coating is intended to not interfere with the neutronic or mechanical performance of the base cladding under normal operating conditions. Different coating materials, thicknesses, coating processes, process parameters, and testing methods have an impact on the microstructure and mechanical properties and therefore on the results of the applied investigation methods. These challenges have motivated an initial focus on demonstrating that the presence of coatings do not perturb the critical performance benchmarks of uncoated material. Ongoing lead test assembly irradiations of coated zirconium concepts in commercial reactions is intended to establish baseline performance in this regard in the coming years.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Transverse Rupture Strength of Uranium Dioxide

Uranium dioxide (UO 2 ) fuel is used as fuel in light water reactors (LWRs). While the fuel pellet is technically the first engineering barrier for radionuclide release, pellet fracturing at intermediate- to high-burnup values releases fission gases into the fuel rod plenum [1, 2]. Therefore, the true engineering barrier is the fuel cladding, which performs very well in LWR environments [3]. The extreme temperature gradients generated by fission energy and the low thermal conductivity of UO 2 quickly induce radial cracking in UO 2 during operation [4]. Cracks in the fuel provide opportunities for fuel relocation, increased fission gas release, and pellet-cladding mechanical interaction (PCMI) [5]. The ability to predict and engineer the fracture of UO 2 fuel pellets using modern computational tools is therefore a key engineering goal that has been the focus of ongoing experimental and computational efforts [6, 7]. Accurate predictions of fuel pellet cracking during operation requires knowledge of more complex phenomena, but improved understanding of the fundamental fracture behavior of unirradiated UO 2 is first necessary.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Microstructural Analysis of Iron-Chromium-Aluminum Samples Exposed to Loca-Type Conditions Followed by Quench

The QUENCH-19 experiment was performed to examine the behavior of FeCrAl-alloy B1236Y3 as a potential nuclear fuel cladding and accident conditions. Over the course of the test, a surrogate bundle achieved a temperature of just over 1400°C. Post-test characterization revealed that the FeCrAl formed a thin layer of aluminum oxide that protected most of the underlying cladding and surrogate fuel pin. However, a few pins were heavily corroded and even destroyed primarily by thermocouple-FeCrAl interactions and subsequent steam, FeCrAl, and ZrO 2 interactions. Absent these effects, it is suggested that FeCrAl’s performance may be acceptable under these conditions.

36 MATERIALS SCIENCE↗