Search NASA⌕ Search

Engineering topics

Nelson, Art J.

Publications and source records attributed to Nelson, Art J..

13 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Changes in electric field noise due to thermal transformation of a surface ion trap

Here, we aim to illuminate how the microscopic properties of a metal surface map to its electric field noise characteristics. In our system, prolonged heat treatments of a metal film can induce a rise in the magnitude of the electric field noise generated by the surface of that film. We refer to this heat-induced rise in noise magnitude as a thermal transformation. The underlying physics of this thermal transformation process is explored through a series of heating, milling, and electron treatments performed on a single surface ion trap. Between these treatments, 40 Ca + ions trapped 70 μm above the surface of the metal are used as detectors to monitor the electric field noise at frequencies close to 1 MHz. An Auger spectrometer is used to track changes in the composition of the contaminated metal surface. With these tools we investigate contaminant deposition, chemical reactions, and atomic restructuring as possible drivers of thermal transformations.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Quantitative XPS of plutonium: Evaluation of the Pu4f peak shape, relative sensitivity factors and estimated detection limits

We report that high-resolution X-ray photoelectron spectra have been acquired from sputter cleaned and in situ oxidized samples of α-plutonium and a face-centred cubic δ-plutonium–gallium alloy. The differences in the Pu4f peak shape in these two materials have been investigated, and the poorly screened satellite peaks have been quantified. Curve fitting parameters for the Pu4p 3/2 , Pu4d 5/2 , Pu4f and Pu6p 3/2 photoelectron peaks are reported, and relative sensitivity factors have been determined. The Pu4f curve fit model has been applied to data acquired using different spectrometers and alloys. Examples of quantification of the plutonium spectra are provided and minimum detection limits are calculated for common impurities in plutonium metal.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Study of cluster ions produced from ToF-SIMS analysis of a U-6%Nb target

Cluster ions have been previously observed during time-of-flight secondary ion mass spectrometry (ToF-SIMS) analysis of metals and metal oxides. Furthermore, we have used ToF-SIMS to investigate cluster ions formed from the hydrocarbon-containing overlayer, the mixed U and Nb surface oxide, and underlying metal of a U-6 %Nb (U6Nb) target. In the overlayer, we observe U x O y + oxides and U-species likely containing hydrocarbons. In the surface oxide, we observe UO 2 +, U 2 O 2 +, U 3 O 5 +, and U 4 O 6 + as the most intense ions for each family of oxide ions containing x U atoms. Nb oxides for NbO 1-2 - were only observed in negative polarity. In contrast to the oxide, analysis of the underlying U6Nb alloy resulted in repeating units of U n +, U n (Nb)+, and U n (Nb 2 ) + ions for n = 3–11 as the highest intensity ions for each family of ions containing n U atoms. Nb n + clusters were not observed. U n +, U n (Nb)+, and U n (Nb 2 )+ clusters containing C- and O-species were observed and were likely produced from soluble C or O species or precipitates known to be present in U6Nb.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Transformations of Ti-5Al-5V-5Cr-3Mo powder due to reuse in laser powder bed fusion: A surface analytical approach

Reactive Ti-5Al-5 V-5Cr-3Mo (Ti5553) alloy feedstock powder is used in laser powder-bed fusion (LPBF). Due to the large quantity of powder necessary for LPBF, powder is reused numerous times under oxidizing environments. Transformations to the powder’s native surface oxide may impact the LPBF process and lead to deviations from expected behavior of printed parts. In this work, we present a multimodal characterization of new and reused powder by combining X-ray photoelectron spectroscopy (XPS), time-of-flight secondary ion mass spectrometry (ToF-SIMS), and transmission electron microscopy (TEM) of focused ion beam (FIB)-prepared cross sections of individual powder particles to understand how the surface oxide composition changes, grows, and becomes hydroxylated and hydrated due to reuse. We show that the native oxide film of Ti5553 powder is a hydroxylated mixed oxide composed of TiO 2 and Al 2 O 3 that grows from 5.6 +/- 0.7 nm to 8.3 +/- 1.1 nm due to reuse. Al oxide regions of the surface oxide become more hydroxylated during reuse in comparison to Ti oxide regions. This indicates that an outer oxide of pure TiO 2 may enhance recyclability of Ti5553 powder while the presence of Al oxides may decrease recyclability. Further characterization of surface transformations due to recyclability may eliminate unnecessary variation in LPBF.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Parabolic oxidation kinetics of a plutonium alloy at room temperature

Auger electron spectroscopy (AES) was used to characterize the oxide scale formed on an ~0.5 wt. % Ga plutonium metal alloy. Analysis of changes to the characteristic Auger transitions for Pu and O during sputter depth profiles were used in combination with previously measured sputter yields to determine the thickness of the oxide scale and provide insight into its chemistry. From this data, the parabolic kinetics for the Pu-Ga alloy were determined as a function of relative humidity, RH = 14–92%, and oxygen partial pressure, p(O 2 ) = 31–157 Torr, at 25°C. For each relative humidity investigated, the parabolic rate constant was found to be independent of oxygen partial pressure. Furthermore, power-law fits to the relative humidity effect on the rate constant was found to have a power of n = 1.265, indicating the diffusion species which rate-limits the reaction isn’t molecular water, which subsequent dissociates at the oxide-metal interface, or hydroxyl from dissociation at the gas-surface interface.

36 MATERIALS SCIENCE↗
DOE OSTI2021

3D Printed Nickel–Molybdenum-Based Electrocatalysts for Hydrogen Evolution at Low Overpotentials in a Flow-Through Configuration

Three-dimensional (3D) printed, hierarchically porous nickel molybdenum (NiMo) electrocatalysts were synthesized and evaluated in a flow-through configuration for the hydrogen evolution reaction (HER) in 1.0 M KOH(aq) in a simple electrochemical H-cell. 3D NiMo electrodes possess hierarchically porous structures because of the resol-based aerogel precursor, which generates superporous carbon aerogel as a catalyst support. Relative to a traditional planar electrode configuration, the flow-through configuration allowed efficient removal of the hydrogen bubbles from the catalyst surface, especially at high operating current densities, and significantly decreased the overpotentials required for HER. An analytical model that accounted for the electrokinetics of HER as well as the mass transport with or without the flow-through configuration was developed to quantitatively evaluate voltage losses associated with kinetic overpotentials and ohmic resistance due to bubble formation in the porous electrodes. Furthermore, the chemical composition, electrochemical surface area (ECSA), and roughness factor (RF) were also systematically studied to assess the electrocatalytic performance of the 3D printed, hierarchically porous NiMo electrodes. An ECSA of 25163 cm2 was obtained with the highly porous structures, and an average overpotential of 45 mV at 10 mA cm–2 was achieved over 24 h by using the flow-through configuration. The flow-through configuration evaluated in the simple H-cell achieved high electrochemical accessible surface areas for electrochemical reactions and provided useful information for adaption of the porous electrodes in flow cells.

08 HYDROGEN↗
DOE OSTI2021

Preparation of large ultrathin free-standing polymer films

A method of making large ultrathin free-standing polymer films without use of a sacrificial layer includes the steps of providing a substrate, applying a polyelectrolyte material to said substrate, applying a polymer material onto said substrate and onto said polyelectrolyte material, and directly delaminating said polymer material from said substrate and said polyelectrolyte to produce the ultrathin free-standing polymer film.

Stadermann, Michael↗
DOE OSTI2021

Observation of Fundamental Mechanisms in Compression-Induced Phase Transformations Using Ultrafast X-ray Diffraction

As theoretically hypothesized for several decades in group IV transition metals, we have discovered a dynamically stabilized body-centered cubic (bcc) intermediate state in Zr under uniaxial loading at sub-nanosecond timescales. Under ultrafast shock wave compression, rather than the transformation from α-Zr to the more disordered hex-3 equilibrium ω-Zr phase, in its place we find the formation of a previously unobserved nonequilibrium bcc metastable intermediate. We probe the compression-induced phase transition pathway in zirconium using time-resolved sub-picosecond x-ray diffraction analysis at the Linac Coherent Light Source. We also present molecular dynamics simulations using a potential derived from first-principles methods which independently predict this intermediate phase under ultrafast shock conditions. In contrast with experiments on longer timescale (> 10 ns) where the phase diagram alone is an adequate predictor of the crystalline structure of a material, our recent study highlights the importance of metastability and time dependence in the kinetics of phase transformations.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Variation in plutonium dioxide sputter yields for 1–5 keV Ar+ ions

An oxide layer with a known thickness and chemistry was grown on delta stabilized Pu and sputtered with 1–5 keV Ar+ ions over a range of incident ion angle between 22° and 72°. From the time required to remove the oxide layer, sputter yields of PuO2 were calculated. The sputter yields appear to increase with higher Ar+ ion beam energy in the range of 1–5 keV at an incident sputter ion angle of 42° and were found to increase with a decreasing angle of incidence up to 62°. The degree of oxide reduction induced during the sputter process was found to vary with the incident sputter ion angle.

Donald, Scott B.↗