Search NASA⌕ Search

Engineering topics

Nelson, B. A.

Publications and source records attributed to Nelson, B. A..

17 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Plasma pressure profiles in a sheared-flow-stabilized Z-pinch

We report the plasma pressure reached inside the central plasma column of a sheared-flow-stabilized Z-pinch using Thomson scattering measurements. Building on previously reported experimental results and the analysis methods established for the high temperature and moderate density plasmas generated on the FuZE device, we show evidence of a central plasma region with higher electron temperature and density, which is consistent with a pinch behavior. Elevated electron temperatures up to 2.25 ± 0.8 keV and densities up to (4.9±0.2)×1017 cm−3 are observed to temporally coincide with the fusion neutron production from the plasma. Reconstructed plasma pressure profiles highlight the presence of a several millimeter-wide column with elevated pressure whose location varies shot-to-shot. The plasma pressure rises as neutron production from the deuterium plasma increases, reaching a peak value of 2.6 kBar. This peak value is consistent with a radially force-balanced pinch equilibrium model based on the measured ∼320 kA pinch current. Complete datasets were obtained at two axial locations, 10 and 20 cm axial position from the tip of the central electrode, which corroborate the estimated neutron source axial lengths.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Elevated Electron Temperature Coincident with Observed Fusion Reactions in a Sheared-Flow-Stabilized Z Pinch

The sheared-flow-stabilized Z pinch concept has been studied extensively and is able to produce fusion-relevant plasma parameters along with neutron production over several microseconds. In this work, we present elevated electron temperature results spatially and temporally coincident with the plasma neutron source. An optical Thomson scattering apparatus designed for the FuZE device measures temperatures in the range of 1–3 keV on the axis of the device, 20 cm downstream of the nose cone. The 17-fiber system measures the radial profiles of the electron temperature. Scanning the laser time with respect to the neutron pulse time over a series of discharges allows the reconstruction of the T e temporal response, confirming that the electron temperature peaks simultaneously with the neutron output, as well as the pinch current and inductive voltage generated within the plasma. Comparison to spectroscopic ion temperature measurements suggests a plasma in thermal equilibrium. The elevated T e confirms the presence of a plasma assembled on axis, and indicates limited radiative losses, demonstrating a basis for scaling this device toward net gain fusion conditions.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Demonstration of transient CHI startup using a floating biased electrode configuration

Abstract Results from the successful solenoid-free plasma startup using the method of transient coaxial helicity injection (transient CHI) in the QUEST spherical tokamak (ST) are reported. Unlike previous applications of CHI on HIT-II and on NSTX which required two toroidal insulating breaks to the vacuum vessel, QUEST uses a first of its kind, floating single biased electrode configuration, which does not use such a vacuum break. Instead, the CHI electrode is simply insulated from the outer lower divertor plate support structure. This configuration is much more suitable for implementation in a fusion reactor than the previous configurations. Transient CHI generated toroidal currents of 135 kA were obtained. The toroidal current during the formation of a closed flux configuration was over 50 kA. These results bode well for the application of transient CHI in a new generation of compact high-field STs and tokamaks in which the space for the central solenoid is very restricted.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Implementation of extreme ultraviolet spectroscopy on a sheared-flow-stabilized Z pinch

A diagnostic for extreme ultraviolet spectroscopy was fielded on the sheared-flow-stabilized (SFS) fusion Z-pinch experiment (FuZE-Q) for the first time. The spectrometer collected time-gated plasma emission spectra in the 5–40 nm wavelength (30–250 eV) range for impurity identification, radiative power studies, and for plasma temperature and density measurements. The unique implementation of the diagnostic included fast (10 ns risetime) pulsed high voltage electronics and a multi-stage differential pumping system that allowed the vacuum-coupled spectrometer to collect three independently timed spectra per FuZE-Q shot while also protecting sensitive internal components. Analysis of line emission identifies oxygen (N-, C-, B-, Be-, Li-, and He-like O), peaking in intensity shortly after maximum current (>500 kA). This work provides a foundation for future high energy spectroscopy experiments on SFS Z-pinch devices.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Probing local electron temperature and density inside a sheared flow stabilized Z-pinch using portable optical Thomson scattering

We report the first optical Thomson scattering measurements inside a high electron temperature (≳1 keV) and moderate electron density (mid 10 16 cm –3 ) plasma. This diagnostic has been built to provide critical plasma parameters, such as electron temperature and density, for Advanced Research Projects Agency-Energy-supported fusion-energy concepts. It uses an 8 J laser at 532 nm in 1.5 ns to measure the high frequency feature of the Thomson scattering profile at 17 locations along the probe axis. It is able to measure electron density from 5 × 10 17 cm –3 to several 10 19 cm –3 and electron temperatures from tens of eV to several keV. Here, in this paper, we describe the design, deployment, and analysis on the sheared flow stabilized Z-pinch machine at Zap Energy named FuZE. The probe beam is aimed at an axial distance of 20 cm from the central electrode and is timed within the temporal envelope of neutron emission. The high temperature and moderate density plasmas generated on FuZE lie in an unconventional regime for Thomson scattering as they are between tokamaks and laser-produced plasmas. We described the analysis considerations in this regime, show that the electron density was below 5 × 10 16 cm –3 at all times during these measurements, and present a sample shot where the inferred electron temperature varied from 167 ± 16 eV to 700 ± 85 eV over 1.6 cm.

47 OTHER INSTRUMENTATION↗
DOE OSTI2022

Improvements to the High-Field-Side Transient CHI System on QUEST

Transient coaxial helicity injection (CHI) is a promising candidate for solenoid-free plasma current start-up in a low-aspect-ratio tokamak in support of developing fully non-inductive scenarios. The aim of the transient CHI research on QUEST is to develop a reactor-relevant CHI design. On QUEST, a CHI discharge is initiated by driving current along magnetic field lines that connect an electrically insulated electrode plate (which is referred to as a bias electrode) to a vessel component at the bottom region of the spherical tokamak. In the first application of CHI on QUEST, the electrically insulated electrode plate was biased with respect to the outer vessel in a configuration referred to as low-field-side (LFS) injection. To maintain a narrow injector flux footprint width throughout the discharge, QUEST is now developing a high-field-side (HFS) injection configuration, in which the electrically insulated electrode plate is biased with respect to the inner vessel components. Through the implementation of a CHI-dedicated gas injection system, studies in the HFS injection configuration have now demonstrated good magnetic flux evolution into the vacuum vessel. Toroidal currents up to 43 kA have been achieved, and the generated current has increased in proportion to the magnetic flux connecting the electrodes. Finally, these results which show agreement with the CHI-scaling suggest that much higher levels of toroidal current can be generated on QUEST in an optimized CHI system in which the magnetic flux connecting the CHI electrodes is further increased.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

High-speed feedback control of an oscillating magnetic helicity injector using a graphics processing unit

A real-time control system has been developed to control the amplitude, phase, and offset of bulk plasma parameters inside an oscillating magnetic helicity injector. Control software running entirely on an Nvidia Tesla P40 graphical processing unit is able to receive digitizer inputs and send response patterns to a Pulse Width Modulation (PWM) controller with a minimum control loop period of 12.8μs. With an input digitization rate of 10 MS/s, a three-parameter proportional integral differential controller is shown to be sufficient to inform the PWM controller to drive the desired oscillating plasma waveform with a frequency of 16.6 kHz that is located near the resonance of a coupled RLC circuit. In particular, the temporal phase of the injector waveform is held within 10 degrees of the target value. Control is demonstrated over the toroidal modal structure of the imposed magnetic perturbations of the helicity injection system, allowing a new class of discharges to be studied.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Flow Z-pinch plasma production on the FuZE experiment

The Fusion Z Pinch Experiment (FuZE) investigates sheared-flow stabilization of classic m = 0 and m = 1 instabilities in Z pinches with an embedded axial flow. FuZE consists of a 100 cm coaxial plasma accelerator, where neutral gas is ionized and accelerated in a pulsed electrical discharge, followed by a 50 cm assembly region, where pinches are formed. Maintaining the pinch requires continuous plasma injection provided by a deflagration mode in the coaxial accelerator. Two discharge modes, with and without deflagration, are investigated on FuZE. Pinch formation is observed with deflagration only. Plasma velocities in the assembly region are found to match the E × B velocity estimated in the accelerator based on a 1D circuit model, indicating that a 1D MHD approximation may offer a valid description of the plasma in the accelerator channel. The velocity of magnetic field propagation is found to agree with the snowplow model based on momentum conservation, and the lifetime of the pinch is shown to be in agreement with constraints imposed by mass conservation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Plasma Exhaust in a Sheared-Flow-Stabilized Z Pinch

The fusion Z-pinch experiment device produces a 0.3 cm radius by 50 cm-long Z pinch between the end of the inner electrode of a coaxial plasma gun and an end wall 50 cm away. The plasma column is stabilized for thousands of instability growth times by an embedded radially sheared axial plasma flow. To investigate the effect of end wall design on Z-pinch plasma behavior, the solid end wall with a central exhaust port is replaced with a spoked end wall with a solid hub. While the Z-pinch plasma behavior was largely unaffected, the plasma exhausted from the Z-pinch provides an experimental platform to study magnetic confinement and detachment. Here, current and density signals are compared between two cases: a low energy and a high energy case. Plasma is found to be frozen-in flux in the Z-pinch assembly region. The exhaust of plasma from the flux conserving region is found to be dependent on the ratio of plasma ram and thermal pressures to the local magnetic pressure, calculated from an equilibrium model at the end wall. Plasma exhaust is observed to increase with the spoked end wall only for the high energy conditions as its ratio of ram and thermal pressures to the magnetic pressure increases.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2019

The nature and source of solar magnetic phenomena

The heliosphere appears to be powered by coaxial helicity injection from a negative helicity injector in the northern hemisphere and a positive one in the southern hemisphere. The injector magnetic flux for both is the measured solar polar magnetic flux, and the injector voltage is generated by a simple dynamo effect due to the differential rotation of the solar surface with the polar magnetic flux. The dynamo current is estimated from the solar motion that it causes. This current also appears to sustain a thin, shallow global magnetic structure over most of the solar surface that has the form of a 1D minimum energy state. The current channel appears to be destroyed and reformed every 11 years. The currents and magnetic fields reverse in this solar cycle. A brief discussion of surface phenomena observed during this cycle is given. Plasma self-organization is briefly discussed and used in this analysis of solar data. The magnetic phenomena discussed include torsional oscillations, the heat source for the chromosphere and the corona, filaments, meridional flow, the solar cycle, sunspots, CMEs, and flares.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2019

Kinetic simulations of sheared flow stabilization in high-temperature Z-pinch plasmas

We present that the first fully kinetic particle-in-cell (PIC) simulations of sheared flow stabilized Z-pinch plasmas show the suppression of the sausage instability by shear, ∂ r v z ≠ 0, with flow Mach numbers ≲1, consistent with experimental observations. Experimental investigations of sheared-flow stabilized Z-pinches demonstrated stability for 10 s of microseconds, over 1000 Alfvén radial transit times, in quasi steady-state plasmas that are an intermediate between conventional inertial and magnetic confinement systems. The observed stability coincides with the presence of radial shear in axial flow profiles with peak speeds less than Mach 1, and experiments are underway to validate scaling this design to fusion conditions. The experimentally observed stability agrees with models of m = 1 kink mode suppression by sheared flows, but existing models of the m = 0 sausage mode underestimate the efficacy of sheared flow stabilization. These models rely on fluid approximations and find that stabilization requires flows ranging from Mach 1.7 to 4.3, and in some cases, stabilization is not reproduced in the models. This is faster than the measured flows in long-lived plasmas and would necessitate substantial energy convection out of the Z-pinch and the need to drive and sustain supersonic flows in future devices. The MHD models typically used in the literature are invalid in the high-temperature, high-current environments desirable for many Z-pinch applications, and they ignore large Larmor radius effects and viscous dissipation which are known to impact Z-pinch stability. PIC simulations can capture all these effects as well as kinetic instabilities that could influence the performance of high-temperature sheared flow stabilized Z-pinch plasmas. The PIC simulations presented here show the suppression and damping of m = 0 modes by sheared flows ∂ r v z = 0.75v A /r 0 with flow Mach numbers ≲1. Lastlyl, equivalent stability occurs under plasma conditions ranging from the limits of present-day experimental capabilities to the projected conditions of a sheared flow stabilized Z-pinch reactor.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2019

Sustained Neutron Production from a Sheared-Flow Stabilized Z Pinch

The sheared-flow stabilized Z pinch has demonstrated long-lived plasmas with fusion-relevant parameters. Here we present the first experimental results demonstrating sustained, quasi-steady-state neutron production from the fusion Z -pinch experiment, operated with a mixture of 20% deuterium/80% hydrogen by pressure. Neutron emissions lasting approximately 5 μs are reproducibly observed with pinch currents of approximately 200 kA during an approximately 16 μs period of plasma quiescence. The average neutron yield is estimated to be ( 1.25 ± 0.45 ) x 10 5 neutrons / pulse and scales with the square of the deuterium concentration. Coincident with the neutron signal, plasma temperatures of 1–2 keV and densities of approximately 10 17 cm -3 with 0.3 cm pinch radii are measured with fully integrated diagnostics.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS1985

Probabilistic computer model of optimal runway turnoffs

Landing delays are currently a problem at major air carrier airports and many forecasters agree that airport congestion will get worse by the end of the century. It is anticipated that some types of delays can be reduced by an efficient optimal runway exist system allowing increased approach volumes necessary at congested airports. A computerized Probabilistic Runway Turnoff Model which locates exits and defines path geometry for a selected maximum occupancy time appropriate for each TERPS aircraft category is defined. The model includes an algorithm for lateral ride comfort limits.

Schoen, M. L.↗
NASA NTRS1975

Micro-organism distribution sampling for bioassays

Purpose of sampling distribution is to characterize sample-to-sample variation so statistical tests may be applied, to estimate error due to sampling (confidence limits) and to evaluate observed differences between samples. Distribution could be used for bioassays taken in hospitals, breweries, food-processing plants, and pharmaceutical plants.

Nelson, B. A.↗
NASA NTRS1971

Microbial burden prediction model program

Model supplements biological surveys of spacecraft by simulating microbial burden accumulation process during periods when surveys are not taken. Important application of model is to predict microbial loading on spacecraft landing capsule immediately prior to terminal heat sterilization.

Meuser, R. F.↗