Search NASA⌕ Search

Engineering topics

Nelson, George J.

Publications and source records attributed to Nelson, George J..

At least 19 records

A machine learning decision criterion for reducing scan time for hyperspectral neutron computed tomography systems

We present the first machine learning-based autonomous hyperspectral neutron computed tomography experiment performed at the Spallation Neutron Source. Hyperspectral neutron computed tomography allows the characterization of samples by enabling the reconstruction of crystallographic information and elemental/isotopic composition of objects relevant to materials science. High quality reconstructions using traditional algorithms such as the filtered back projection require a high signal-to-noise ratio across a wide wavelength range combined with a large number of projections. This results in scan times of several days to acquire hundreds of hyperspectral projections, during which end users have minimal feedback. To address these challenges, a golden ratio scanning protocol combined with model-based image reconstruction algorithms have been proposed. This novel approach enables high quality real-time reconstructions from streaming experimental data, thus providing feedback to users, while requiring fewer yet a fixed number of projections compared to the filtered back projection method. In this paper, we propose a novel machine learning criterion that can terminate a streaming neutron tomography scan once sufficient information is obtained based on the current set of measurements. Our decision criterion uses a quality score which combines a reference-free image quality metric computed using a pre-trained deep neural network with a metric that measures differences between consecutive reconstructions. The results show that our method can reduce the measurement time by approximately a factor of five compared to a baseline method based on filtered back projection for the samples we studied while automatically terminating the scans.

97 MATHEMATICS AND COMPUTING↗

The Complex, Unique, and Powerful Imaging Instrument for Dynamics (CUPI 2 D) at the Spallation Neutron Source (invited)

The Oak Ridge National Laboratory is planning to build the Second Target Station (STS) at the Spallation Neutron Source (SNS). STS will host a suite of novel instruments that complement the First Target Station’s beamline capabilities by offering an increased flux for cold neutrons and a broader wavelength bandwidth. A novel neutron imaging beamline, named the Complex, Unique, and Powerful Imaging Instrument for Dynamics (CUPI 2 D), is among the first eight instruments that will be commissioned at STS as part of the construction project. CUPI 2 D is designed for a broad range of neutron imaging scientific applications, such as energy storage and conversion (batteries and fuel cells), materials science and engineering (additive manufacturing, superalloys, and archaeometry), nuclear materials (novel cladding materials, nuclear fuel, and moderators), cementitious materials, biology/medical/dental applications (regenerative medicine and cancer), and life sciences (plant–soil interactions and nutrient dynamics). The innovation of this instrument lies in the utilization of a high flux of wavelength-separated cold neutrons to perform real time in situ neutron grating interferometry and Bragg edge imaging—with a wavelength resolution of δλ/λ ≈ 0.3%—simultaneously when required, across a broad range of length and time scales. This manuscript briefly describes the science enabled at CUPI 2 D based on its unique capabilities. The preliminary beamline performance, a design concept, and future development requirements are also presented.

47 OTHER INSTRUMENTATION↗

Electrochemical Response of Alkaline Batteries Subject to Quasi-Static and Dynamic Loading

We report electrochemical changes were successfully monitored through the coupling of external loading, electrochemical impedance spectroscopy (EIS), and distribution of relaxation times (DRT) analysis. The development of the testing methods allows for detailed observation of changes due to mechanical loading and distinguishes responses between different cell geometries. Comparison of the force vs displacement, voltage vs displacement, and distribution of relaxation times plots to the different cell geometries display failure modes specific to geometry as well as the impact of different loading profiles. Numerical modeling confirmed the movement within individual cells and predicted locations with the most deformation based on the external loading condition applied. The results gathered from combining mechanical loading, electrochemical response, and numerical modeling, yield a viable approach to establishing an improved understanding of the effects of mechanical loading on the electrochemical response of multiple battery geometries and the methods herein may be extensible to additional battery chemistries.

25 ENERGY STORAGE↗

Multiscale Electrochemomechanics Interaction and Degradation Analytics of Sn Electrodes for Sodium-Ion Batteries

Sodium-ion batteries have emerged as a strong contender among the beyond lithium-ion chemistries due to elemental abundance and the low cost of sodium. Tin (Sn) is a promising alloying electrode with high capacity, redox reversibility, and earth abundance. Tin electrodes, however, undergo a series of intermediate reactions exhibiting multiple voltage plateaus upon sodiation/desodiation. Phase transformations related to incomplete sodiation in tin during cycling, in the presence of a frail solid electrolyte interphase layer, can quickly weaken the structural stability. The structural dynamics and reactivity of the electrode/electrolyte interface, being further dependent on the size and morphology of the active material particle in the presence of different electrolytes, dictate the electrode degradation and survivability during cycling. Here, we paint a comprehensive picture of the underpinnings of the electrochemical and mechanics coupling and electrode/electrolyte interfacial interactions in alloying Sn electrodes. We elicit the fundamental role of electrode/electrolyte complexations in the Sn electrode structure-property-performance relationship based on multimodal analytics, including electrochemical, microscopy, and tomography analyses.

25 ENERGY STORAGE↗

Cycling-Induced Microstructural Changes in Alloy Anodes for Lithium-Ion Batteries

Abstract High-capacity electrochemical alloying materials, such as tin and tin-based alloys, present an opportunity for the advancement of lithium-ion batteries. However, the destructive effects of volumetric expansion must be mitigated in order to sustain this high capacity during extended cycling. One way to mitigate these effects is by alloying Sn with more malleable metals to accommodate the strain related to severe volumetric expansion. Ex situ X-ray microtomography data of cycled Cu6Sn5 pellets were used to quantify the microstructural changes that occur during lithiation and delithiation. The microtomography data were segmented into three distinct phases to evaluate phase size distributions, specific surface area, and tortuosity. Electrodes lithiated and then delithiated showed the most substantial reduction in overall phase sizes. This suggests that full lithiation of the Sn followed by partial delithiation of the Li4.4Sn to Li2CuSn can cause substantial microstructural changes related to volume expansion on lithiation and structural collapse upon delithiation. When considering other microstructural characteristics, this subset of the electrodes analyzed showed the highest tortuosity values. These results show that in addition to the mechanical degradation of the electrodes, excessive volume expansion can also influence transport networks in the active material and supporting phases of the electrode. While based on studies of the active–inactive alloy Cu6Sn5 for lithium-ion battery applications, the insights obtained are expected to be applicable to other alloy electrodes and battery chemistries.

Electrochemistry↗

In Operando XANES Imaging of High Capacity Intermetallic Anodes for Lithium Ion Batteries

In operando 2D X-ray absorption near edge structure (XANES) imaging was performed near the Cu K-edge during cycling of Cu 6 Sn 5 composite anodes for lithium ion batteries. Galvanostatic lithiation and delithiation with intermittent constant voltage holds near reaction plateaus show evolution of absorption spectra for active material particles. XANES spectra obtained from images taken during cycling were compared to standard spectra for Cu, Cu 6 Sn 5 , and Li 2 CuSn. Chemical composition was assessed for Cu-containing phases. Distinct Cu, Cu 6 Sn 5 , and Li 2 CuSn regions were identified for each voltage plateau. Mechanical degradation, electrode particle fracture and expansion were observed during delithiation. Furthermore, movement of particles during cycling suggests that expansion also impacts the supporting secondary phases and the transport networks therein. These results demonstrate that spectroscopic X-ray imaging methods can clearly distinguish chemically distinct phases in alloy electrodes and have the versatility to observe the evolution of these phases during lithiation and delithiation.

25 ENERGY STORAGE↗

Quantifying Transport, Geometrical, and Morphological Parameters in Li-Ion Cathode Phases Using X-ray Microtomography

The charge/discharge capabilities of Li-ion cathodes are influenced by the meso-scale geometry, transport properties, and morphological parameters of the constituent phases in the cathode: active material, binder, conductive additive, and pore. Electrode processing influences the structure and attendant properties of these constituents. Thus, performance of the battery can be enhanced by correlating various electrode processing techniques with the charge/discharge behavior in the lithium-ion cathodes. X-ray microtomography was used to image samples obtained from pristine Li(Ni 1/3 Mn 1/3 Co 1/3 )O 2 (NMC) cathodes subjected to distinct processing approaches. Two sample preparation approaches were applied to the samples prior to microtomography. Casting the samples in epoxy yielded only the cathode active material domain. Encapsulating the sample with Kapton tape yielded phase contrast data that permitted segmentation of the active material and combined carbon/binder and pore regions. Here, geometrical and morphological details of the active material and the secondary phases were characterized and compared between the varied processing approaches. Calendered and ball-milled samples exhibited distinct differences in both geometry and morphology. Drying modes demonstrated variation in the distribution of the secondary and pore phases. Applying phase contrast capabilities, the processing–morphology relationship can be better understood to enhance overall battery performance across multiple scales.

36 MATERIALS SCIENCE↗

A search for gravitationally lensed quasars and quasar pairs in Pan-STARRS1: spectroscopy and sources of shear in the diamond 2M1134−2103

Abstract We present results of a systematic search for gravitationally lensed quasars in Pan-STARRS1. Our final sample of candidates comprises of 91 systems, not including 25 rediscovered lensed quasars and quasar pairs. In the absence of spectroscopy to verify the lensing nature of the candidates, the main sources of contaminants are likely to be quasar pairs, which we consider to be a byproduct of our work, and a smaller number of quasar + star associations. Among the independently discovered quads is 2M1134−2103, for which we obtained spectroscopy for the first time, finding a redshift of 2.77 for the quasar. There is evidence for microlensing in at least one image. We perform detailed mass modelling of this system using archival imaging data, and find that the unusually large shear responsible for the diamond-like configuration can be attributed mainly to a faint companion ∼4 arcsec away, and to a galaxy group/cluster ∼30 arcsec away. We also set limits of z ∼ 0.5–1.5 on the redshift of the lensing galaxy, based on its brightness, the image separation of the lensed images, and an analysis of the observed photometric flux ratios.

Rusu, Cristian E.↗

Elucidating Lithium Alloying-Induced Degradation Evolution in High-Capacity Electrodes

Alloy electrode materials offer high capacity in lithium ion batteries; however, they exhibit rapid degradation resulting in particle disintegration and electrochemical performance decay. Here in this study, the evolution of lithium alloying induced degradation due to electrochemo-mechanical interactions is examined based on a multi-pronged electrochemical and microstructural analysis. Copper-tin (Cu 6 Sn 5 ) is chosen as an exemplary alloy electrode material. Electrodes with compositional variations were fabricated and electrochemical performance was examined under varying conditions including voltage window, C-rate, and short- and long-term cycling. Morphology and composition analyses of pristine and cycled electrodes were conducted using micrography and spectroscopy techniques. Alloying induced electrode microstructural evolution was probed using X-ray microtomography. The rapid capacity fading was found to be caused by mechanical degradation of the electrode. Driving the electrode to a lower potential (E ≈ 0.2 V vs. Li/Li + ) induced Li-Sn alloy formation and provided the characteristic large capacity; however, this led to a large volume expansion and active particle cracking and disintegration. Copper expulsion was found to be a consequence of the alloy formation; however, it was not the primary contributor to the dramatic electrochemical performance decay.

25 ENERGY STORAGE↗

Electrolyzer Exergy Analysis for an Environmental Control and Life Support System

An exergy based analysis of the Environmental Control and Life Support System (ECLSS) aboard the International Space Station (ISS) is conducted to assess its overall performance. Exergy is chosen as a measure of performance because it accounts for both the first and second laws of thermodynamics. The exergy efficiency of a system is first defined as the total exergy destroyed by the system relative to the total exergy input to the system. To determine the ECLSS exergy efficiency, the system is divided into constituent subsystems which in turn are divided into assemblies and components. Based on this system decomposition, exergy balances are derived for each assembly or component. Exergy balances and supporting calculations are implemented in MATLAB® code. The major subsystems of the ECLSS considered in this analysis include the Atmosphere Revitalization Subsystem (ARS), Atmosphere Control and Supply Subsystem (ACS), Temperature and Humidity Control Subsystem (THC), Water Recovery and Management Subsystem (WRM), and Waste Management Subsystem (WM). This paper focuses on the ARS and its constituent assemblies and components. Exergy efficiency of the ARS and its constituent assemblies and components is first presented. The Oxygen Generation Assembly (OGA), an assembly within the ARS, is then highlighted because the exergy destruction by the OGA is a large magnitude contributor to the overall exergy destruction of the ECLSS. The OGA produces oxygen to meet the crew's metabolic demand via water electrolysis in a proton exchange membrane (PEM) electrolyzer. The exergy destruction of the OGA's PEM electrolyzer is a function of the amount of oxygen produced, which determines the necessary current density and voltage drop across the PEM electrolyzer. In addition, oxygen production in the PEM electrolyzer requires deviation from the Nernst potential, presenting trade-offs between the exergy efficiency and critical life support functions. The results of parametric studies of PEM electrolyzer performance are presented with an emphasis on the impacts of polarization and operational conditions on exergy efficiency.

Chow, Raymond↗

Discovery of the First Quadruple Gravitationally Lensed Quasar Candidate with Pan-STARRS

We report the serendipitous discovery of the first gravitationally lensed quasar candidate from Pan-STARRS. The grizy images reveal four point-like images with magnitudes between 14.9 and 18.1 mag. The colors of the point sources are similar, and they are more consistent with quasars than with stars or galaxies. The lensing galaxy is detected in the izy bands, with an inferred photometric redshift of ∼0.6, lower than that of the point sources. We successfully model the system with a singular isothermal ellipsoid with shear, using the relative positions of the five objects as constraints. While the brightness ranking of the point sources is consistent with that of the model, we find discrepancies between the model-predicted and observed fluxes, likely due to microlensing by stars and millilensing due to the dark matter substructure. In order to fully confirm the gravitational lens nature of this system and add it to the small but growing number of the powerful probes of cosmology and astrophysics represented by quadruply lensed quasars, we require further spectroscopy and high-resolution imaging.

79 ASTRONOMY AND ASTROPHYSICS↗

Exergy Based Analysis for the Environmental Control and Life Support Systems of the International Space Station

When optimizing the performance of complex systems, a logical area for concern is improving the efficiency of useful energy. The energy available for a system to perform work is defined as a system's energy content. Interactions between a system's subsystems and the surrounding environment can be accounted for by understanding various subsystem energy efficiencies. Energy balance of reactants and products, and enthalpies and entropies, can be used to represent a chemical process. Heat transfer energy represents heat loads, and flow energy represents system flows and filters. These elements allow for a system level energy balance. The energy balance equations are developed for the subsystems of the Environmental Control and Life Support (ECLS) system aboard the International Space Station (ISS). The use of these equations with system information would allow for the calculation of the energy efficiency of the system, enabling comparisons of the ISS ECLS system to other systems as well as allows for an integrated systems analysis for system optimization.

Clem, Kirk A.↗