Search NASASearch

Engineering topics

Nerem, R. S.

Publications and source records attributed to Nerem, R. S..

At least 19 records

Simulation Study of a Follow-on Gravity Mission to GRACE

The gravity recovery and climate experiment (GRACE) has been providing monthly estimates of the Earth's time-variable gravity field since its launch in March 2002. The GRACE gravity estimates are used to study temporal mass variations on global and regional scales, which are largely caused by a redistribution of water mass in the Earth system. The accuracy of the GRACE gravity fields are primarily limited by the satellite-to-satellite range-rate measurement noise, accelerometer errors, attitude errors, orbit errors, and temporal aliasing caused by unmodeled high-frequency variations in the gravity signal. Recent work by Ball Aerospace and Technologies Corp., Boulder, CO has resulted in the successful development of an interferometric laser ranging system to specifically address the limitations of the K-band microwave ranging system that provides the satellite-to-satellite measurements for the GRACE mission. Full numerical simulations are performed for several possible configurations of a GRACE Follow-On (GFO) mission to determine if a future satellite gravity recovery mission equipped with a laser ranging system will provide better estimates of time-variable gravity, thus benefiting many areas of Earth systems research. The laser ranging system improves the range-rate measurement precision to approximately 0.6 nm/s as compared to approx. 0.2 micro-seconds for the GRACE K-band microwave ranging instrument. Four different mission scenarios are simulated to investigate the effect of the better instrument at two different altitudes. The first pair of simulated missions is flown at GRACE altitude (approx. 480 km) assuming on-board accelerometers with the same noise characteristics as those currently used for GRACE. The second pair of missions is flown at an altitude of approx. 250 km which requires a drag-free system to prevent satellite re-entry. In addition to allowing a lower satellite altitude, the drag-free system also reduces the errors associated with the accelerometer. All simulated mission scenarios assume a two satellite co-orbiting pair similar to GRACE in a near-polar, near-circular orbit. A method for local time variable gravity recovery through mass concentration blocks (mascons) is used to form simulated gravity estimates for Greenland and the Amazon region for three GFO configurations and GRACE. Simulation results show that the increased precision of the laser does not improve gravity estimation when flown with on-board accelerometers at the same altitude and spacecraft separation as GRACE, even when time-varying background models are not included. This study also shows that only modest improvement is realized for the best-case scenario (laser, low-altitude, drag-free) as compared to GRACE due to temporal aliasing errors. These errors are caused by high-frequency variations in the hydrology signal and imperfections in the atmospheric, oceanographic, and tidal models which are used to remove unwanted signal. This work concludes that applying the updated technologies alone will not immediately advance the accuracy of the gravity estimates. If the scientific objectives of a GFO mission require more accurate gravity estimates, then future work should focus on improvements in the geophysical models, and ways in which the mission design or data processing could reduce the effects of temporal aliasing.

Loomis, Bryant D.

Design Considerations for a Dedicated Gravity Recovery Satellite Mission Consisting of Two Pairs of Satellites

Future satellite missions dedicated to measuring time-variable gravity will need to address the concern of temporal aliasing errors; i.e., errors due to high-frequency mass variations. These errors have been shown to be a limiting error source for future missions with improved sensors. One method of reducing them is to fly multiple satellite pairs, thus increasing the sampling frequency of the mission. While one could imagine a system architecture consisting of dozens of satellite pairs, this paper explores the more economically feasible option of optimizing the orbits of two pairs of satellites. While the search space for this problem is infinite by nature, steps have been made to reduce it via proper assumptions regarding some parameters and a large number of numerical simulations exploring appropriate ranges for other parameters. A search space originally consisting of 15 variables is reduced to two variables with the utmost impact on mission performance: the repeat period of both pairs of satellites (shown to be near-optimal when they are equal to each other), as well as the inclination of one of the satellite pairs (the other pair is assumed to be in a polar orbit). To arrive at this conclusion, we assume circular orbits, repeat groundtracks for both pairs of satellites, a 100-km inter-satellite separation distance, and a minimum allowable operational satellite altitude of 290 km based on a projected 10-year mission lifetime. Given the scientific objectives of determining time-variable hydrology, ice mass variations, and ocean bottom pressure signals with higher spatial resolution, we find that an optimal architecture consists of a polar pair of satellites coupled with a pair inclined at 72deg, both in 13-day repeating orbits. This architecture provides a 67% reduction in error over one pair of satellites, in addition to reducing the longitudinal striping to such a level that minimal post-processing is required, permitting a substantial increase in the spatial resolution of the gravity field products. It should be emphasized that given different sets of scientific objectives for the mission, or a different minimum allowable satellite altitude, different architectures might be selected.

Wiese, D. N.

Gravity Models from CHAMP and other Satellite Data

CHAMP spacecraft is the first of a series of new spacecraft missions that are revolutionizing our ability to model the Earth's geopotential. We report on the analysis of over 100 days of CHAMP data in 2001 and 2002, merged with tracking data of other satellites such as Jason, Topex, GFO, Starlette, Stella, Spot-2, as well as satellite altimetry. We find that the CHAMP-only component of these solutions is a significant improvement over pre-CHAMP satellite only models with respect to the high degree information expressed by the geopotential model coefficients. For example, the variance of the differences with altimeter-derived anomalies through degree 70 is 2.80 mGal(sup 2) for the CHAMP-only solution based on 87 days of data vs. 10.19 mGal(sup 2) for EGM96S. Nonetheless, in order to model properly the various resonances to which different satellites are sensitive, we must include other satellite data. We evaluate the performance of these new CHAMP derived solutions with EGM96 and the EIGEN series of solutions. We review carefully the performance of these models for altimetric satellites.

Lemoime, Frank G.

An Assessment of Gravity Recovery with CHAMP Data

The CHAMP mission, launched in July 2000, is the first in the series of mapping missions for the Earth's geopotential scheduled for the first decade of the new millenium. Its unique contributions compared to all the previous generation of satellites whose data have been included in Earth geopotential models are the precision global tracking with GPS data, and the availability of precision accelerometry data to model the nonconservative forces. Over the past year we have implemented extensive modifications to our GEODYN orbit determination processing code and ancillary data preprocessors to process the GPS and accelerometry data from missions such as CHAMP and GRACE. We report on the analysis of up to 60 days of CHAMP data and how these data contribute to Earth geopotential solutions where the base model is a derivative of EGM96. Preliminary results with only 12.5 days of data processed clearly show the ability of the CHAMP data to improve the modeling of the zonals (1=10 to 40), the m-dailies, the primary resonance terms, and the sectoral harmonics. We will detail the results of our calibrations of the CHAMP accelerometry and assess the quality of test solutions that include these CHAMP data.

Lemoine, F. G.

Recent Results from CHAMP Tracking and Accelerometer Data Analysis

The CHAMP mission's unique combination of sensors and orbit configuration will enable unprecedented improvements in modeling and understanding the Earth's static gravity field and its temporal variations. CHAMP is the first of two missions (GRACE to be launched in the early part of 02') that combine a new generation of Global Positioning System (GPS) receivers, a high precision three-axis accelerometer, and star cameras for the precision attitude determination. In order to isolate the gravity signal for science investigations, it is necessary to perform a detailed reduction and analysis of the GPS and Satellite Laser Ranging (SLR) tracking data in conjunction with the accelerometer and attitude data. Precision orbit determination based on the GPS and SLR tracking data will isolate the orbit perturbations, while the accelerometer data will be used to distinguish the non-gravitational forces from those due to the geopotential (static, and time varying). In preparation for the CHAMP and GRACE missions, extensive modifications have been made to NASA/GSFC's GEODYN orbit determination software to enable the simultaneous reduction of spacecraft tracking (e.g. GPS and SLR), three-axis accelerometer and precise attitude data. Several weeks of CHAMP tracking and accelerometer data have been analyzed and the results will be presented. Precision orbit determination analysis based on tracking data alone in addition to results based on the simultaneous reduction of tracking and accelerometer data will be discussed. Results from a calibration of the accelerometer will be presented along with the results from various orbit determination strategies.

Luthcke, S. B.

CHAMP Tracking and Accelerometer Data Analysis Results

The CHAMP (Challenging Minisatellite Payload) mission's unique combination of sensors and orbit configuration will enable unprecedented improvements in modeling and understanding the Earth's static gravity field and its temporal variations. CHAMP is the first of two missions (GRACE (Gravity Recovery and Climate Experiment) to be launched in the later part of '01) that combine a new generation of GPS (Global Positioning System) receivers, a high precision three axis accelerometer, and star cameras for the precision attitude determination. In order to isolate the gravity signal for science investigations, it is necessary to perform a detailed reduction and analysis of the GPS and SLR tracking data in conjunction with the accelerometer and attitude data. Precision orbit determination based on the GPS and SLR (Satellite Laser Ranging) tracking data will isolate the orbit perturbations, while the accelerometer data will be used to distinguish the surface forces from those due to the geopotential (static, and time varying). In preparation for the CHAMP and GRACE missions, extensive modifications have been made to NASA/GSFC's GEODYN orbit determination software to enable the simultaneous reduction of spacecraft tracking (e.g. GPS and SLR), three axis accelerometer and precise attitude data. Several weeks of CHAMP tracking and accelerometer data have been analyzed and the results will be presented. Precision orbit determination analysis based on tracking data alone in addition to results based on the simultaneous reduction of tracking and accelerometer data will be discussed. Results from a calibration of the accelerometer will be presented along with the results from various orbit determination strategies. Gravity field modeling status and plans will be discussed.

Lemoine, Frank G.

Gravity Fields from CHAMP Mission Data

The CHAMP mission, launched in July 2000, is the first in a series of missions that will revolutionize our ability to model the Earth s geopotential. The CHAMP spacecraft is equipped for precision tracking by the Global Positioning System (GPS) and Satellite Laser Ranging (SLR) along with a precision accelerometer to provide measurements of the surface forces. Preliminary satellite-only geopotential solutions with only 30 days of CHAMP data are, by some criteria, as strong as solutions made from tracking data collected over the previous 30 years of the space age. Compared to EGM96, CHAMP makes notable contributions in regions where the terrestrial data (surface gravimetry and altimetry) were weak, for example in the polar regions, in the Amazon and the Himalayas. The CHAMP data allow us to separate the geoid from the dynamic ocean topography (DOT) up to at least degree 25 rather than just under degree 20 as in EGM96. We report on satellite-only and combination models that incorporate up to 100 days of CHAMP data as well as other satellite data. We report on our updated processing of the CHAMP tracking and accelerometer data and evaluate the performance of the geopotential models using a variety of tests.

Lemoine, Frank G.

Precision orbit determination for TOPEX/POSEIDON

The TOPEX/POSEIDON mission objective requires that the radial position of the spacecraft be determined with an accuracy better than 13 cm RMS (root mean square). This stringent requirement is an order of magnitude below the accuracy achieved for any altimeter mission prior to the definition of the TOPEX/POSEIDON mission. To satislfy this objective, the TOPEX Precision Orbit determination (POD) Team was established as a joint effort between the NASA Goddard Space Flight Center and the University of Texas at Austin, with collaboration from the University of Colorado and the Jet Propulsion Laboratory. During the prelaunch development and the post launch verification phases, the POD team improved, calibrated, and validated the precision orbit determination computer software systems. The accomplishments include (1) increased accuracy of the gravity and surface force models and (2) improved peformance of both laser ranging and Doppler tracking systems. The result of these efforts led to orbit accuracies for TOPEX/POSEIDON which are significantly better than the original mission requirement. Tests based on data fits, covariance analysis, and orbit comparisons indicate that the radial component of the TOPEX/POSEIDON spacecraft is determined, relative to the Earth's mass center, with an root mean square (RMS) error in the range of 3 to 4 cm RMS. This orbit accuracy, together with the near continuous dual-frequency altimetry from this mission, provides the means to determine the ocean's dynamic topography with an unprecedented accuracy.

Tapley, B. D.

Gravity model development for TOPEX/POSEIDON: Joint gravity models 1 and 2

The TOPEX/POSEIDON (T/P) prelaunch Joint Gravity Model-1 (JGM-1) and the postlaunch JGM-2 Earth gravitational models have been developed to support precision orbit determination for T/P. Each of these models is complete to degree 70 in spherical harmonics and was computed from a combination of satellite tracking data, satellite altimetry, and surface gravimetry. While improved orbit determination accuracies for T/P have driven the improvements in the models, the models are general in application and also provide an improved geoid for oceanographic computations. The postlaunch model, JGM-2, which includes T/P satellite laser ranging (SLR) and Doppler orbitography and radiopositioning integrated by satellite (DORIS) tracking data, introduces radial orbit errors for T/P that are only 2 cm RMS with the commission errors of the marine geoid for terms to degree 70 being +/- 25 cm. Errors in modeling the nonconservative forces acting on T/P increase the total radial errors to only 3-4 cm root mean square (RMS), a result much better than premission goals. While the orbit accuracy goal for T/P has been far surpassed geoid errors still prevent the absolute determination of the ocean dynamic topography for wavelengths shorter than about 2500 km. Only a dedicated gravitational field satellite mission will likely provide the necessary improvement in the geoid.

Nerem, R. S.

A preliminary evaluation of ocean topography from the TOPEX/POSEIDON mission

We have analyzed 50 ten-day cycles of TOPEX/POSEIDON (T/P) altimeter data to evaluate the ocean dynamic topography and its temporal variations. We have employed data from both the U.S. and French altimeters along with the NASA precision orbits in this analysis. Errors in the diurnal and semidiurnal components of the Cartwright-Ray tide model have been significantly reduced using a correction developed from a combination of JGM-2 and OSU91A was employed, as well as a geoid model based solely on OSU91A. The long wavelengths of the comparisons to historical data, although geoid error still corrupts the dynamic topography for wavelengths shorter than 2500 km. The root mean square (RMS) variability is similar to previous results from Geosat, with bakground 'noise' approaching 3 cm RMS. The computed annual and semiannual variations are also similar to previous Geosat results, although the hemispheric distribution of the annual heating cycle is much better presented in the T/P results. They also compare reasonably well with the Levitus hydrographic compilation in the northern hemisphere, although the T/P variations generally have larger amplitudes. Ten-day average maps of variations in sea level compare well with simulations measurements at ocean tide gauges, with RMS differences of less than 4 cm and correlations greater than 0.6 for most of the island gauges. Time-longitude plots of these sea level variations at different latitudes in the Pacific clearly show the presence of equatorial Kelvin waves and Rossby waves, with the wave speeds agreeing well with theoretical and observed values. Measurement of variations in global sea level over cycles 2-51 have an RMS variability of 6.3 mm and a rate of change of -3.5 +/- 8 mm/yr, the uncertainty primarily due to insufficient averaging of the interannual and periodic sea level variations. These results show that the accuracy of the T/P measurements of sea level has dramatically improved over previous missions, with estimated time variable errors of 4 cm or less. Although geographically correlated orbit errors have also been reduced to the few centimeter level, further improvement in determinations of the mean dynamic topography will be difficult to obtain until a more accurate model of the marine geoid is available.

Nerem, R. S.

Observations of geographically correlated orbit errors for TOPEX/Poseidon using the global positioning system

We have compared Global Positioning System (GPS)-based dynamic and reduced-dynamic TOPEX/Poseidon orbits over three 10-day repeat cycles of the ground-track. The results suggest that the prelaunch joint gravity model (JGM-1) introduces geographically correlated errors (GCEs) which have a strong meridional dependence. The global distribution and magnitude of these GCEs are consistent with a prelaunch covariance analysis, with estimated and predicted global rms error statistics of 2.3 and 2.4 cm rms, respectively. Repeating the analysis with the post-launch joint gravity model (JGM-2) suggests that a portion of the meridional dependence observed in JGM-1 still remains, with global rms error of 1.2 cm.

Christensen, E. J.

Gravity model improvement using the DORIS tracking system on the SPOT 2 satellite

A high-precision radiometric satellite tracking system, Doppler Orbitography and Radio-positioning Integrated by Satellite system (DORIS), has recently been developed by the French space agency, Centre National d'Etudes Spatiales (CNES). DORIS was designed to provide tracking support for missions such as the joint United States/French TOPEX/Poseidon. As part of the flight testing process, a DORIS package was flown on the French SPOT 2 satellite. A substantial quantity of geodetic quality tracking data was obtained on SPOT 2 from an extensive international DORIS tracking network. These data were analyzed to assess their accuracy and to evaluate the gravitational modeling enhancements provided by these data in combination with the Goddard Earth Model-T3 (GEM-T3) gravitational model. These observations have noise levels of 0.4 to 0.5 mm/s, with few residual systematic effects. Although the SPOT 2 satellite experiences high atmospheric drag forces, the precision and global coverage of the DORIS tracking data have enabled more extensive orbit parameterization to mitigate these effects. As a result, the SPOT 2 orbital errors have been reduced to an estimated radial accuracy in the 10-20 cm RMS range. The addition of these data, which encompass many regions heretofore lacking in precision satellite tracking, has significantly improved GEM-T3 and allowed greatly improved orbit accuracies for Sun-synchronous satellites like SPOT 2 (such as ERS 1 and EOS). Comparison of the ensuing gravity model with other contemporary fields (GRIM-4C2, TEG2B, and OSU91A) provides a means to assess the current state of knowledge of the Earth's gravity field. Thus, the DORIS experiment on SPOT 2 has provided a strong basis for evaluating this new orbit tracking technology and has demonstrated the important contribution of the DORIS network to the success of the TOPEX/Poseidon mission.

Nerem, R. S.

A geopotential model from satellite tracking, altimeter, and surface gravity data: GEM-T3

An improved model of Earth's gravitational field, Goddard Earth Model T-3 (GEM-T3), has been developed from a combination of satellite tracking, satellite altimeter, and surface gravimetric data. GEM-T3 provides a significant improvement in the modeling of the gravity field at half wavelengths of 400 km and longer. This model, complete to degree and order 50, yields more accurate satellite orbits and an improved geoid representation than previous Goddard Earth Models. GEM-T3 uses altimeter data from GEOS 3 (1975-1976), Seasat (1978) and Geosat (1986-1987). Tracking information used in the solution includes more than 1300 arcs of data encompassing 31 different satellites. The recovery of the long-wavelength components of the solution relies mostly on highly precise satellite laser ranging (SLR) data, but also includes Tracking Network (TRANET) Doppler, optical, and satellite-to-satellite tracking acquired between the ATS 6 and GEOS 3 satellites. The main advances over GEM-T2 (beyond the inclusion of altimeter and surface gravity information which is essential for the resolution of the shorter wavelength geoid) are some improved tracking data analysis approaches and additional SLR data. Although the use of altimeter data has greatly enhanced the modeling of the ocean geoid between 65 deg N and 60 deg S latitudes in GEM-T3, the lack of accurate detailed surface gravimetry leaves poor geoid resolution over many continental regions of great tectonic interest (e.g., Himalayas, Andes). Estimates of polar motion, tracking station coordinates, and long-wavelength ocean tidal terms were also made (accounting for 6330 parameters). GEM-T3 has undergone error calibration using a technique based on subset solutions to produce reliable error estimates. The calibration is based on the condition that the expected mean square deviation of a subset gravity solution from the full set values is predicted by the solutions' error covariances. Data weights are iteratively adjusted until this condition for the error calibration is satisfied. In addition, gravity field tests were performed on strong satellite data sets withheld from the solution (thereby ensuring their independence). In these tests, the performance of the subset models on the withheld observations is compared to error projections based on their calibrated error covariances. These results demonstrate that orbit accuracy projections are reliable for new satellites which were not included in GEM-T3.

Lerch, F. J.

Calibration of TOPEX/Poseidon at Platform Harvest

We present preliminary estimates for the mean bias of the TOPEX/Poseidon NASA altimeter (ALT) and the CNES altimeter (SSALT) using in situ data gathered at platform Harvest during the first 36 cycles of the mission. Data for 21 overflights of the ALT and 3 overflights of the SSALT have been analyzed.

TOPEX/Poseidon

An improved gravity model for Mars: Goddard Mars Model 1

Doppler tracking data of three orbiting spacecraft have been reanalyzed to develop a new gravitational field model for the planet Mars, Goddard Mars Model 1 (GMM-1). This model employs nearly all available data, consisting of approximately 1100 days of S band tracking data collected by NASA's Deep Space Network from the Mariner 9 and Viking 1 and Viking 2 spacecraft, in seven different orbits, between 1971 and 1979. GMM-1 is complete to spherical harmonic degree and order 50, which corresponds to a half-wavelength spatial resolution of 200-300 km where the data permit. GMM-1 represents satellite orbits with considerably better accuracy than previous Mars gravity models and shows greater resolution of identifiable geological structures. The notable improvement in GMM-1 over previous models is a consequence of several factors: improved computational capabilities, the use of otpimum weighting and least squares collocation solution techniques which stabilized the behavior of the solution at high degree and order, and the use of longer satellite arcs than employed in previous solutions that were made possible by improved force and measurement models. The inclusion of X band tracking data from the 379-km altitude, nnear-polar orbiting Mars Observer spacecraft should provide a significant improvement over GMM-1, particularly at high latitudes where current data poorly resolve the gravitational signature of the planet.

Smith, D. E.

An improved gravity model for Mars: Goddard Mars Model-1 (GMM-1)

Doppler tracking data of three orbiting spacecraft have been reanalyzed to develop a new gravitational field model for the planet Mars, GMM-1 (Goddard Mars Model-1). This model employs nearly all available data, consisting of approximately 1100 days of S-bank tracking data collected by NASA's Deep Space Network from the Mariner 9, and Viking 1 and Viking 2 spacecraft, in seven different orbits, between 1971 and 1979. GMM-1 is complete to spherical harmonic degree and order 50, which corresponds to a half-wavelength spatial resolution of 200-300 km where the data permit. GMM-1 represents satellite orbits with considerably better accuracy than previous Mars gravity models and shows greater resolution of identifiable geological structures. The notable improvement in GMM-1 over previous models is a consequence of several factors: improved computational capabilities, the use of optimum weighting and least-squares collocation solution techniques which stabilized the behavior of the solution at high degree and order, and the use of longer satellite arcs than employed in previous solutions that were made possible by improved force and measurement models. The inclusion of X-band tracking data from the 379-km altitude, near-polar orbiting Mars Observer spacecraft should provide a significant improvement over GMM-1, particularly at high latitudes where current data poorly resolves the gravitational signature of the planet.

Smith, D. E.

Temporal variations of the earth's gravitational field from satellite laser ranging to LAGEOS

Monthly values of the J2 and J3 earth gravitational coefficients were estimated using LAGEOS satellite laser ranging data collected between 1980 and 1989. Monthly variations in gravitational coefficients caused by atmospheric mass redistribution were calculated using measurements of variations in surface atmospheric pressure. Results for correlation studies of the two time series are presented. The LAGEOS and atmospheric J2 time series agree well and it appears that variations in J2 can be attributed to the redistribution of atmospheric mass. Atmospheric and LAGEOS estimates for J3 show poorer agreement, J3 estimates appear to be very sensitive to unmodeled forces acting on the satellite. Results indicate that the LAGEOS data can be used to detect small variations in the gravitational field.

Nerem, R. S.