Engineering topics

Nesman, T.

Publications and source records attributed to Nesman, T..

5 records

NASA NTRS2000

Data Oscillation Resolution of Propellant Flowmeter Used in FASTRAC Engine Testing

The Stennis Space Centers' horizontal test facility, Marshall Space Flight Centers' propulsion test article and the X-34 flight vehicle are designed with V-cone flowmeters for measurement of both RP-1 and LOX flow-rates for Fastrac engine testing. Delta pressure transducer data from these flowmeters are used to calibrate the RP-1 and LOX mixture ratio in the Fastrac engine. Data from the V-Cone flowmeter delta pressure transducers have excessive oscillation. The delta pressure oscillations have caused flowrate data fluctuations that interfered with making the accurate readings necessary to calibrate the RP-1 and LOX mixture ratio required for Fastrac engine operation. The objective of this report is to document the flowmeter data oscillation problem and the method used to obtain more reliable flowmeter data.

Heflin, J.↗

NASA NTRS1993

Unsteady Flow Simulations in Support of the SSME HEX Turning Vane Cracking Investigation with the ATD HPOTP

Unsteady flow computations are being performed with the P&W (ATD) and the Rocketdyne baseline configurations of the SSME LO2 turbine turnaround duct (TAD) and heat exchanger (HEX). The work is in support of the HEX inner turning vane cracking investigation. Fatigue cracking has occurred during hot firings with the P&W configuration on the HEX inner vane, and it appears the fix will involve changes to the TAD splitter vane position and to the TAD inner wall curvature to reduce the dynamic loading on the inner vane. Unsteady flow computations on the P&W baseline and fix and on the Rocketdyne baseline reference follow steady-flow screening computations done by MSFC/ED32 on several trial configurations arriving at the fix. The P&W TAD inlet velocity profile has a strong radial velocity component that directs the flow toward the inner wall and raises the local velocity a factor of two and the dynamic pressure a factor, of four. The fix is intended to redistribute the flow more evenly across the HEX inner and outer vanes like the Rocketdyne baseline reference. Vane buffeting at frequencies around 4,000 Hz is the leading suspected cause of the problem. Our simulations (work in progress) are being done with the USA 2D axisymmetric code approximating the flow as axisymmetric u+v 2D (axial, u, and radial, v, components only). The HEX coils are included in the model to make sure the fix does not adversely affect the HEX environment. Turbulent kinetic energy, k, levels where k = 1/2 v' rms2 are locally as high as 10,000 ft2/sec2 for the P&W baseline at the engine interface (between the TAD and HEX) at the HEX inner vane location. However, k is less than 8,000 on the HEX outer vane and only about 4,500 on the HEX inner vane for the Rocketdyne baseline. Unsteady turbulence intensity, v'rms/v, and pressure, p', are being computed in the present computations to compare with steady-flow Reynolds-averaged computations where p'rms = const (pk) for overall rms random turbulence from 0.1 to 12,000 Hz frequency. Random overall static, p'rms fluctuations as large as 1.7 psi are estimated from k on the HEX inner vane for the P&W baseline configuration but only about 0.7 psi for the Rocketdyne configuration.

Dougherty, N. S.↗

NASA NTRS1991

Stability testing of a modified Space Shuttle Main Engine

The testing of the combustion stability characteristics of Space Shuttle Main Engine (SSME) 0208 is described in terms of augmenting the technology base for large O/H thrust-chamber assemblies. The throat area is increased by 12 percent over that of the flight SSMEs, and the thrust chamber assembly does not include stability aids. Acoustic modes in the chamber are excited by means of rapid pressure generators employed in the start-transient through mainstage operations. Stability characteristics are determined by damp times which are facilitated by high-frequency instrumentation measuring oscillations and locating stable operating regions. All vibration modes are damped to within the requirements for a chamber mode set forth by the Chemical Propulsion Information Agency. No sustained chamber acoustic oscillations are exhibited in engine 0208's combustion chamber configuration in spite of the absence of baffles and acoustic cavities.

Dennis, H.↗

NASA NTRS1991

Time accurate Navier-Stokes computations of solid rocket motor internal field joint cavity flows

The low-speed flow of combustion gases in the Space Shuttle Solid Rocket Motor (SRM) following ignition are investigated with a time-accurate CFD technique. The flow of the combustion gases is examined in the forward joint section of the SRM at 80 s after ignition with attention given to the amplification of existing 'organ-pipe' modes of 15, 30, and 45 Hz resulting from frequency lock-in with vortex-shedding modes. The CFD code employed is a multizone compressible Navier-Stokes flow solver using a finite-volume, upwind-biased, total-variation-diminishing scheme. The vortex-generated oscillations generated by the inhibitor and the cavity at the forward field joint are described in terms of amplitude and frequency and related to the flow dynamics in the SRM. Oscillations are shown to occur spontaneously when the trailing edge of the cavity at the joint is sharp and can be amplified if the unburned portion of the inhibitor protrudes into the flow.

Farr, Rebecca A.↗

NASA NTRS1988

Vortex shedding experiment with flat and curved bluff plates in water

Vortex shedding experiments were conducted in a water flow facility in order to simulate the strong discrete 4000-Hz vibration detected in the Space Shuttle Main Engine (SSME) which is thought to be associated with the SSME LOX inlet tee splitter vanes on the Main Injector. For the case of a flat vane with a blunt trailing edge excited by flow induced vortex shedding, lock-in with the first bending mode of the plate was observed. A curved vane displayed similar behavior, with the lock-in being a more discrete higher amplitude response. Aluminum vanes were employed to decouple the first vane bending mode from the vortex shedding mode. The application of an asymmetric 30-deg trailing edge bevel to both the flat and curved vanes was found to greatly reduce the strength of the shed vortices.

Reed, D.↗