Search NASA⌕ Search

Engineering topics

Nettie H. Roozeboom

Publications and source records attributed to Nettie H. Roozeboom.

15 records
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Joint Acceptance Attenuation Factor of Integrated Pressure with Unsteady Pressure-Sensitive Paint Measurements

The Unsteady Pressure-Sensitive Paint (uPSP) is widely used to measure the surface pressure of the scaled model in the wind tunnel tests. Compared to the conventional pressure transducers, uPSP has the advantage of high spatial resolution. With multiple high-speed cameras, the uPSP data collected with the camera pixels are mapped to the surface grid of the scaled model and converted to pressure. The shot noise, which is associated with the quantum processes both in the generation of the photons by the luminescent uPSP and in the conversion of the photons into electrons within the camera, is the dominant component of the noise in the uPSP measurement. The integrated pressure is usually computed as an area-weighted average of the uPSP measured pressures on the grid nodes of a user-defined patch. The effect of the shot noise is reduced in the integrated pressure; however, the measurement of the aerodynamic pressure is also attenuated. This paper discusses the Joint Acceptance Attenuation Factor (JAAF) of the integrated pressure with uPSP measurements. The JAAF is defined as the ratio of the auto or cross Power Spectral Density (PSD) of the integrated aerodynamic pressure on the patch to the average auto PSD of the aerodynamic pressure on the grid nodes of the patch. Under the assumption that the cross spectrum of the aerodynamic pressure can be described with the Corcos model, the closed-form formula of the JAAF is derived for the integrated pressure on rectangular patches via the summation of uPSP measurements on discrete grid nodes. The closed-form formula is verified via the integration of the pressure field of Corcos model over continuous areas. The properties of the JAAF with different parameters are presented and the applications in the comparison of the spectrum of the pressure transducers and uPSP measurements, which were collected in the NASA Space Launch System (SLS) tests with the 11-by-11-foot transonic wind tunnel at NASA Ames Research Center in December 2017 and September 2019 respectively, are also discussed. The work described in this paper is a part of NASA’s development of a new state-of-the-art uPSP capability in production wind tunnels. Funding was provided by the NASA Aerosciences Evaluation and Test Capabilities(AETC) Portfolio Office.

Unsteady Pressure-Sensitive Paint↗
NASA NTRSDate not supplied

NASA's Unsteady Pressure-Sensitive Paint Research and Operational Capability Developments

In the last three years, several advancements have been made to produce a new state-of-the-art capability in the field of Aerosciences. NASA’s Aerosciences Evaluations and Test Capabilities (AETC) Portfolio Office has funded a multi-year project to produce the unsteady Pressure-Sensitive Paint (uPSP) technology as an operational capability in key ground test facilities at NASA. The research and development has primarily been conducted at NASA Ames Research Center’s (ARC) Unitary Plan Wind Tunnel (UPWT) 11-by 11-ft Transonic Wind Tunnel (TWT). The NASA ARC UPWT is one of the ground test facilities under NASA AETC’s Portfolio Office. AETC’s goals are to provide the tools to deliver the technology innovations and breakthroughs necessary to address increasingly complex research and development challenges. AETC’s integrated approach will consider the complimentary high-end compute capabilities necessary to advance analysis in conjunction with ground experimental capabilities. The uPSP Capability Challenge Project is a demonstration of several different technologies: 1) the unsteady Pressure-Sensitive Paint (uPSP) technology, and 2) Project: Red Rover, establishing a secure, reliable, fast connection between experimental and computation facilities, leveraging NASA’s computational resources within the High-End Compute Capability (HECC) Project for processing, storing, and sharing data efficiently. This project demonstrates the technical diversity and technical inclusion need to advance the field of Aerosciences. The approach to combine subject matter experts in experimental methods, optical methods, production wind tunnel testing, network engineering, high-end computing, signal processing, grid generation, and visualization while establishing the required infrastructure for subject matter experts to have access to the data while the wind tunnel test is being conducted. The most recent advancements for the uPSP technology have focused on three key areas: development of data products, robust processing pipeline, operational efficiencies and uncertainty quantification.

buffet↗
NASA NTRSDate not supplied

Methodology for Validation of Unsteady Pressure-Sensitive Paint Measurements using Pressure Transducers

Unsteady Pressure-Sensitive Paint (uPSP) technology provides simultaneously high-frequency and high-spatial resolution surface pressure fluctuation measurements. It has demonstrated value in wind tunnel test facilities to evaluate aerospace vehicle unsteady aerodynamics. The calibration of measurements from digital pixel counts into corresponding physical units relies on both lab-based and in-situ calibration steps, and its validation is both challenging and critical to adoption of the technology. We present a rigorous methodology for direct comparison of uPSP-derived surface pressure measurements to reference pressure transducer data based on a model of the camera-based measurement error, a model of the flow field pressure signal, and their propagation through the uPSP data reduction algorithm. The methodology is demonstrated on data collected in a small-scale, subsonic wind tunnel test as well as data collected from a Space Launch System unsteady aerodynamics characterization test at the NASA Ames Research Center Unitary Plan Wind Tunnel Complex.

Pressure-Sensitive Paint↗
NASA NTRSDate not supplied

Joint Acceptance Attenuation Factor of Integrated Pressure with Unsteady Pressure-Sensitive Paint Measurements

The Unsteady Pressure-Sensitive Paint (uPSP) is widely used to measure the surface pressure of scaled models in wind tunnel tests. Compared to the conventional pressure transducers, uPSP has the advantage of high spatial resolution. With multiple high-speed Complementary Metal Oxide Superconductor (CMOS) cameras, the uPSP data collected with the camera pixels are mapped to the surface grid of the scaled model and converted to pressure. The shot noise is the dominant component of the noise in the uPSP measurement. The integrated pressure is usually computed on the grid nodes of a user-defined patch. The effect of shot noise is reduced in the integrated pressure on the patch; however, the measurement of the aerodynamic pressure may also be attenuated by the decorrelation of the flow pressure field being measured. This paper discusses the Joint Acceptance Attenuation Factor (JAAF) of the integrated pressure with uPSP measurements. The JAAF, a function of frequency, is defined as the ratio of the Power Spectral Density (PSD) of the integrated aerodynamic pressure on the patch to the average PSD of the aerodynamic pressure on the grid nodes of the patch. In this paper, the JAAF is investigated for the integrated pressure on rectangular patches, whose edges are defined in the direction along the streamline or across the streamline. Based on the assumption that the surface pressure field can be described by the Corcos model, the closed-form formulas to compute the JAAFs of the integrated pressure on the discrete grid nodes of a rectangular patch and over the continuous area of a rectangular patch are derived respectively. It is shown that the JAAF of the integrated pressure over the continuous area of a rectangular patch is the limit of that on discrete nodes of the rectangular patch when the number of nodes in each row or column goes to infinity. The closed-form formulas of the JAAF derived in this paper, with estimated parameters of the model, are verified with the measurements of the uPSP and the conventional pressure transducer collected in the Space Launch System Ascent Unsteady Aerodynamics Test at NASA Ames Research Center in November 2017. The closed-form formulas of the JAAF of the integrated pressure on the rectangular patches, based on the Corcos model, provide an efficient method to estimate the attenuation of integration by the decorrelation of the flow pressure field and set references for the comparison of the spectrum of the integrated uPSP measurements and the conventional pressure transducer measurements. The work described in this paper is a part of NASA’s development of a new state-of-the-art uPSP capability in production wind tunnels. Funding was provided by the NASA Aerosciences Evaluation and Test Capabilities Portfolio Office.

acoustics↗
NASA NTRSDate not supplied

Joint Acceptance Attenuation Factor of Integrated Pressure with Unsteady Pressure-Sensitive Paint Measurements

The Unsteady Pressure-Sensitive Paint (uPSP) is widely used to measure the surface pressure of scaled models in wind tunnel tests. Compared to the conventional pressure transducers, uPSP has the advantage of high spatial resolution. With multiple high-speed Complementary Metal Oxide Superconductor (CMOS) cameras, the uPSP data collected with the camera pixels are mapped to the surface grid of the scaled model and converted to pressure. The shot noise is the dominant component of the noise in the uPSP measurement. The integrated pressure is usually computed on the grid nodes of a user-defined patch. The effect of shot noise is reduced in the integrated pressure on the patch; however, the measurement of the aerodynamic pressure may also be attenuated by the decorrelation of the flow pressure field being measured. This paper discusses the Joint Acceptance Attenuation Factor (JAAF) of the integrated pressure with uPSP measurements. The JAAF, a function of frequency, is defined as the ratio of the Power Spectral Density (PSD) of the integrated aerodynamic pressure on the patch to the average PSD of the aerodynamic pressure on the grid nodes of the patch. In this paper, the JAAF is investigated for the integrated pressure on rectangular patches, whose edges are defined in the direction along the streamline or across the streamline. Based on the assumption that the surface pressure field can be described by the Corcos model, the closed-form formulas to compute the JAAFs of the integrated pressure on the discrete grid nodes of a rectangular patch and over the continuous area of a rectangular patch are derived respectively. It is shown that the JAAF of the integrated pressure over the continuous area of a rectangular patch is the limit of that on discrete nodes of the rectangular patch when the number of nodes in each row or column goes to infinity. The closed-form formulas of the JAAF derived in this paper, with estimated parameters of the model, are verified with the measurements of the uPSP and the conventional pressure transducer collected in the Space Launch System Ascent Unsteady Aerodynamics Test at NASA Ames Research Center in November 2017. The closed-form formulas of the JAAF of the integrated pressure on the rectangular patches, based on the Corcos model, provide an efficient method to estimate the attenuation of integration by the decorrelation of the flow pressure field and set references for the comparison of the spectrum of the integrated uPSP measurements and the conventional pressure transducer measurements. The work described in this paper is a part of NASA’s development of a new state-of-the-art uPSP capability in production wind tunnels. Funding was provided by the NASA Aerosciences Evaluation and Test Capabilities Portfolio Office.

acoustics↗
NASA NTRSDate not supplied

Infrared Reflection Removal in Wind Tunnels Using Polarization Theory

Infrared radiometry with infrared cameras allows for high spatial resolution, noncontact measurements in wind tunnel experiments and has been increasingly used to visualize flow features. Reflections from test section walls present a major challenge in collecting these measurements as it is difficult or impossible to separate them from the true model emission signal. This paper outlines a method to quantitatively remove specular reflections using polarization theory for materials common in the Unitary Plan Wind Tunnel. The method was however ultimately ineffective due to unexpected diffuse reflection and was unable to remove the specular reflection. The experiment provided insight into ways that polarization could be utilized to improve data collection capabilities of optical measurement techniques in wind tunnel settings.

Infrared↗
NASA NTRSDate not supplied

Unsteady Pressure Sensitive Paint Camera Calibration Improvements

New challenges have arisen in processing a significantly increased volume of data collected during recent large-scale demonstrations of unsteady pressure-sensitive paint. Techniques designed for several thousands of images collected in a lab do not necessarily scale to tens of millions collected in a large-scale test. New techniques are needed to meet the tighter requirements on robustness and accuracy that accompany larger wind tunnel models, higher camera resolution, and more run conditions per test. This paper outlines several such techniques and improvements in regard to the camera calibration process.

Camera calibration↗
NASA NTRSDate not supplied

NASA’s Unsteady Pressure-Sensitive Paint Research and Operational Capability Developments

To address challenges in the field of unsteady aerodynamics, NASA has developed a new state-of-the-art capability called Unsteady Pressure-Sensitive Paint (uPSP). It has been developed as an operational surface-pressure measurement capability for deployment in NASA’s AETC ground test facilities. Offering unprecedented spatiotemporal resolution, uPSP is an extremely powerful tool for investigating unsteady separated flows. To accelerate scientific discovery, uPSP data is to be processed and distributed as rapidly as it is acquired. Several demonstrations of the technology collected valuable data that has been used to develop data products, a robust processing pipeline, and other computational capabilities. A collection of papers documents the most recent research and development work on the uPSP technology and capability. This paper summarizes the current state of this effort at NASA.

Pressure-Sensitive Paint↗
NASA NTRSDate not supplied

Implementation of the Lifetime Method in Unsteady Pressure Sensitive Paint Measurements

At NASA Ames Research Center, unsteady pressure-sensitive paint (uPSP) measurements are obtained using the ‘intensity method’ which measures paint luminescence in response to a continuous, constant excitation. These measurements are obtained using high-speed cameras and are processed into fluctuating components of pressure. However, the nature of the intensity method also requires a separate steady state (time mean) pressure measurement to be obtained. This steady state measurement has typically been obtained using a separate set of PSP equipment that uses the ‘lifetime method’, which uses pulsed excitation to measure paint decay lifetime. If the lifetime method were implemented in the high-speed uPSP system, both the fluctuating and mean components of pressure could be obtained with a single system. This would greatly streamline setup, operations, and processing. In this paper, we describe work performed at the Fluid Mechanics Laboratory at NASA Ames to implement the lifetime method in our uPSP system. The uPSP acquisition system uses Phantom v2512 high-speed cameras, and it was initially uncertain if results of adequate quality could be obtained - their high framerate comes at the cost of several undesirable characteristics, which are explored in this paper. It was also uncertain if illumination using LED lamps, rather than a stronger source such as lasers, would be adequate. The data acquisition and data processing are discussed and the results analyzed. It was found that satisfactory lifetime method results can indeed be obtained using these high-speed cameras and LED lamps. This will allow the uPSP system to be greatly simplified and will have a large operational impact on how uPSP data is acquired in future wind tunnel tests.

Pressure Sensitive Paint↗
NASA NTRSDate not supplied

NASA’s Unsteady Pressure-Sensitive Paint Research and Operational Capability Developments

To address challenges in the field of unsteady aerodynamics, NASA has developed a new stateof-the-art capability called Unsteady Pressure-Sensitive Paint (uPSP). It has been developed as an operational surface-pressure measurement capability for deployment in NASA’s AETC ground test facilities. Offering unprecedented spatiotemporal resolution, uPSP is an extremely powerful tool for investigating unsteady separated flows. To accelerate scientific discovery, uPSP data is to be processed and distributed as rapidly as it is acquired. Several demonstrations of the technology collected valuable data that has been used to develop data products, a robust processing pipeline, and other computational capabilities. A collection of papers documents the most recent research and development work on the uPSP technology and capability. This paper summarizes the current state of this effort at NASA.

Pressure-Sensitive Paint↗
NASA NTRSDate not supplied

Analysis of Dynamic Mode Decomposition Outputs of Unsteady Pressure-Sensitive Paint Measurements in the NASA Wind Tunnel Tests

This paper discusses the Dynamic Mode Decomposition (DMD) outputs of the Unsteady Pressure-Sensitive Paint (uPSP) measurements, which were collected with four Phantom high-speed cameras at a constant sample frequency in the Ascent Transient Aerodynamics Test (ATAT) of the Space Launch System (SLS) Block 1 cargo vehicle in the 11-by-11-foot transonic test section of the Unitary Plan Wind Tunnel (UPWT) at NASA Ames Research Center in September 2019. In this paper, the effectiveness to use the DMD outputs of uPSP measurements in the diagnosis and analysis of the aerodynamic and acoustic phenomena in the SLS ATAT is demonstrated. The work described in the paper is a part of NASA’s development of a new state-of-the-art uPSP capability in production wind tunnels. Funding was provided by the NASA Aerosciences Evaluation and Test Capabilities (AETC) Project.

acoustics↗
NASA NTRSDate not supplied

Advancements in the Camera Setup for Unsteady Pressure Sensitive Paint at NASA Ames Research Center

A test in the Unitary Plan Wind Tunnel at NASA Ames Research Center is scheduled for early 2024 with the intent of showcasing improvements made to unsteady Pressure Sensitive Paint technology. Analysis was performed to investigate how to maximize the system resolving power by optimizing the camera parameters, specifically focal length and focusing distance, while still subject to other system requirements such as field of view and relatively low illumination from the paint. Additionally, the system is upgrading to an 8-camera system from a 4-camera system, so analysis was performed to determine the best way to extend that system to maximize camera coverage and how to most effective reduce the system uncertainty by averaging multiple measurement using camera overlap. These analyses have uncovered new opportunities to improve the unsteady Pressure Sensitive Paint technology without the need for new or expensive hardware and will allow the system to collect better data with simple changes to the design process.

Camera Calibration↗
NASA NTRSDate not supplied

Aeroacoustic Analysis using Dynamic Mode Decomposition of Unsteady Pressure-Sensitive Paint Measurements

In this paper, we present a new method for the diagnosis and analysis of aeroacoustic phenomena. Taking advantage of the well-known property that the measurements of the Unsteady Pressure-Sensitive Paint (uPSP) have much higher spatial resolution compared to those of the conventional pressure transducers, the method is based on the visualization and analysis of the outputs of the Dynamic Mode Decomposition (DMD) of the uPSP measurements. The uPSP measurements were collected with four Phantom high-speed cameras in the Ascent Transient Aerodynamics Test (ATAT) of the Space Launch System (SLS) Block 1 cargo vehicle in the 11-by-11-foot transonic test section of the Unitary Plan Wind Tunnel (UPWT) at NASA Ames Research Center in September 2019. The method presented in this paper is demonstrated by investigating an interesting phenomenon observed in the SLS ATAT – the vortex shedding tone generated by the forward attachment of the Solid Rocket Booster (SRB). As examples, the DMD outputs of the uPSP measurements in a subsonic test in the SLS ATAT are presented. It is shown the information retrieved from the DMD outputs of the uPSP measurements can be effectively used in the identification and diagnosis of the aeroacoustic phenomena. The work described in this paper is a part of NASA’s development of a new state-of-the-art uPSP capability in production wind tunnels. Funding was provided by the NASA Aerosciences Evaluation and Test Capabilities Portfolio Office.

acoustics↗
NASA NTRSDate not supplied

Aeroacoustic Analysis using Dynamic Mode Decomposition of Unsteady Pressure-Sensitive Paint Measurements

In this paper, we present a new method for the diagnosis and analysis of aeroacoustic phenomena. Taking advantage of the well-known property that the measurements of the Unsteady Pressure-Sensitive Paint (uPSP) have much higher spatial resolution compared to those of the conventional pressure transducers, the method is based on the visualization and analysis of the outputs of the Dynamic Mode Decomposition (DMD) of the uPSP measurements. The uPSP measurements were collected with four Phantom high-speed cameras in the Ascent Transient Aerodynamics Test (ATAT) of the Space Launch System (SLS) Block 1 cargo vehicle in the 11-by-11-foot transonic test section of the Unitary Plan Wind Tunnel (UPWT) at NASA Ames Research Center in September 2019. The method presented in this paper is demonstrated by investigating an interesting phenomenon observed in the SLS ATAT – the vortex shedding tone generated by the forward attachment of the Solid Rocket Booster (SRB). As examples, the DMD outputs of the uPSP measurements in a subsonic test in the SLS ATAT are presented. It is shown the information retrieved from the DMD outputs of the uPSP measurements can be effectively used in the identification and diagnosis of the aeroacoustic phenomena. The work described in this paper is a part of NASA’s development of a new state-of-the-art uPSP capability in production wind tunnels. Funding was provided by the NASA Aerosciences Evaluation and Test Capabilities Portfolio Office.

acoustics↗