Search NASA⌕ Search

Engineering topics

Newman, J. C., Jr.

Publications and source records attributed to Newman, J. C., Jr..

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

Dugdale plastic zone size and CTOD equations for the compact specimen

With the aim of applying the Dugdale model to the compact specimen, the equations for stress intensity factor and crack surface displacement are obtained for a pair of pin loads and a uniform stress acting on a segment of the crack surface. The plastic zone size is calculated from the 'finiteness' condition of Dugdale, and the results agree well with collocation results from Terada (1983). The load that causes incipient yielding at the compression point of the compact specimen is calculated from a finite element strip yield analysis for an elastic-perfectly plastic material. The crack tip opening displacement for the compact specimen is calculated by adding the displacement at the tip of the physical crack length due to the pin load and due to the uniform stress. The results are within 1.5 percent of current collocation results.

Newman, J. C., Jr.↗
NASA NTRS1984

An elastic-plastic finite element analysis of crack initiation, stable crack growth, and instability

Studies have been conducted to develop efficient techniques to simulate crack extension and to examine various local and global fracture criteria. Of the considered criteria, the crack-tip-opening angle (CTOA) or displacement (CTOD) at a specified distance from the crack tip was shown to be most suited for modeling stable crack growth and instability during the fracture process. The results obtained in a number of studies show the necessity for studying different crack configurations when assessing the validity of any fracture criteria. One of the objectives of the present investigation is related to a critical evaluation of the CTOD growth criterion using an elastic-plastic finite element analysis under monotonic loading to failure. The analysis was found to predict three stages of crack growth behavior under monotonic loading to failure. Calculated CTOD values agreed well with experimental values for crack growth initiation.

Newman, J. C., Jr.↗
NASA NTRS1983

The Dugdale model for the compact specimen

Plastic zone size and crack tip opening displacement (CTOD) equations were developed. Boundary collocation analyses were used to analyze the compact specimen subjected to various loading conditions (pin loads, concentrated forces, and uniform pressure acting on the crack surface). Stress intensity factor and crack surface displacement equations for some of these loadings were developed and used to obtain the Dugdale model. The results from the equations for plastic zone size and CTOD agreed well with numerical values calculated by Terada for crack length to width ratios greater than 0.4.

Mall, S.↗
NASA NTRS1983

A nonlinear fracture mechanics approach to the growth of small cracks

An analytical model of crack closure is used to study the crack growth and closure behavior of small cracks in plates and at notches. The calculated crack opening stresses for small and large cracks, together with elastic and elastic plastic fracture mechanics analyses, are used to correlate crack growth rate data. At equivalent elastic stress intensity factor levels, calculations predict that small cracks in plates and at notches should grow faster than large cracks because the applied stress needed to open a small crack is less than that needed to open a large crack. These predictions agree with observed trends in test data. The calculations from the model also imply that many of the stress intensity factor thresholds that are developed in tests with large cracks and with load reduction schemes do not apply to the growth of small cracks. The current calculations are based upon continuum mechanics principles and, thus, some crack size and grain structure exist where the underlying fracture mechanics assumptions become invalid because of material inhomogeneity (grains, inclusions, etc.). Admittedly, much more effort is needed to develop the mechanics of a noncontinuum. Nevertheless, these results indicate the importance of crack closure in predicting the growth of small cracks from large crack data.

Newman, J. C., Jr.↗
NASA NTRS1983

Aspects of fracture mechanics in cryogenic model design. Part 2: NTF materials

Results of fatigue crack growth and fracture toughness tests conducted on three candidate materials are presented. Fatigue crack growth and fracture toughness tests were conducted on NITRONIC 40 at room temperature and -275 F. Fracture toughness tests were also conducted on Vascomax 200 and 250 maraging steel from room temperature to -320 F. NITRONIC 40 was used to make the Pathfinder 1 model. The fatigue crack growth rate tests were conducted at room temperature and -275 F on three-point notch bend specimens. The fracture toughness tests on the as received and stress relieved materials at -275 F were conducted on the center crack tension specimens. Toughness tests were also conducted on Vascomax CVM-200 and CVM-250 maraging steel from room temperature to -320 F using round and rectangular compact specimens.

Newman, J. C., Jr.↗
NASA NTRS1983

A critical study of the crack closure effect on near-threshold fatigue crack growth

Crack closure in the near-crack-tip region has been considered to be an important contribution to the development of a crack-growth threshold for macroscopic cracks. Recent analytical work, however, has suggested that closure well back of the tip may be the controlling factor. In order to check on this possibility, material has been machined away far behind the crack tip in order to eliminate long-range closure. Removal of this material did not eliminate the threshold, but did lower the threshold level by approximately 10 percent for tests conducted on 6.3 mm-thick X7090-T6 powder metallurgy aluminum alloy.

Minakawa, K.↗
NASA NTRS1982

Finite-element analysis of initiation, stable crack growth and instability using a crack-tip-opening displacement criterion

An elastic-plastic (incremental and small strain) finite element analysis was used with a crack growth criterion to study crack initiation, stable crack growth, and instability under monotonic loading to failure of metallic materials. The crack growth criterion was a critical crack-tip-opening displacement (CTOD) at a specified distance from the crack tip, or equivalently, a critical crack-tip-opening angle (CTOA). Whenever the CTOD (or CTOA) equaled or exceeded a critical value, the crack was assumed to grow. Single values of critical CTOD were used in the analysis to model crack initiation, stable crack growth, and instability for 7075-T651 and 2024-T351 aluminum alloy compact specimens. Calculated and experimentally measured CTOD values at initiation agreed well for both aluminum alloys. These critical CTOD values were also used to predict failure loads on center-crack tension specimens and a specially-designed three-hole-crack tension specimen made of the two aluminum alloys and of 304 stainless steel. All specimens were 12.7 mm thick. Predicted failure loads for 7075-T651 aluminum alloy and 304 stainless steel specimens were generally within + or - 15 percent of experimental failure loads, whereas the predicted failure loads for 2024-T351 aluminum alloy specimens were generally within + or - 5 percent of the experimental loads.

Newman, J. C., Jr.↗
NASA NTRS1981

Stress-intensity factors and crack-opening displacements for round compact specimens

An improved method of boundary collocation based on the complex variable analysis of Muskhelishvili (1953) is applied to the two-dimensional stress analysis of round compact specimens with pin-loaded holes. Stress intensity factors and crack opening displacements are calculated for various round compact specimens as a function of crack-length-to-specimen-width ratios. A wide-range equation for the stress intensity factors and equations for crack-surface displacements and load-point displacements are developed.

Newman, J. C., Jr.↗
NASA NTRS1981

Stress-intensity factor equations for cracks in three-dimensional finite bodies

Empirical stress intensity factor equations are presented for embedded elliptical cracks, semi-elliptical surface cracks, quarter-elliptical corner cracks, semi-elliptical surface cracks at a hole, and quarter-elliptical corner cracks at a hole in finite plates. The plates were subjected to remote tensile loading. Equations give stress intensity factors as a function of parametric angle, crack depth, crack length, plate thickness, and where applicable, hole radius. The stress intensity factors used to develop the equations were obtained from three dimensional finite element analyses of these crack configurations.

Newman, J. C., Jr.↗
NASA NTRS1981

A crack-closure model for predicting fatigue-crack growth under aircraft spectrum loading

The development and application of an analytical model of cycle crack growth is presented that includes the effects of crack closure. The model was used to correlate crack growth rates under constant amplitude loading and to predict crack growth under aircraft spectrum loading on 2219-T851 aluminum alloy sheet material. The predicted crack growth lives agreed well with experimental data. The ratio of predicted to experimental lives ranged from 0.66 to 1.48. These predictions were made using data from an ASTM E24.06.01 Round Robin.

Newman, J. C., Jr.↗
NASA NTRS1981

Prediction of fatigue-crack growth under variableamplitude and spectrum loading using a closure model

An existing analytical crack closure model was used to study crack growth under various load histories. The model was based on a concept like the Dugdale model, but modified to leave plastically deformed material in the wake of the advancing crack tip. The model was used to correlate crack growth rates under constant amplitude loading, and to predict crack growth under variable amplitude and aircraft spectrum loading on 2219-T851 aluminum alloy sheet material. The predicted crack growth lives agreed well with experimental data. For 80 crack growth tests subjected to various load histories, the ratio of predicted-to-experimental lives (N(P)/n(T)) ranged from 0.5 to 1.8. The mean value of N(P)/N(T) was 0.97 and the standard deviation was 0.27.

Newman, J. C., Jr.↗
NASA NTRS1981

An empirical stress-intensity factor equation for the surface crack

This paper presents an empirical stress-intensity factor equation for a surface crack as a function of parametric angle, crack depth, crack length, plate thickness and plate width for tension and bending loads. The stress-intensity factors used to develop the equation were obtained from a previous three-dimensional, finite-element analysis of semielliptical surface cracks in finite elastic plates subjected to tension or bending loads. A wide range of configuration parameters was included in the equation. The ratios of crack length to plate thickness and the ratios of crack depth to crack length ranged from 0 to 1.0. The effects of plate width on stress-intensity variations along the crack front were also included. The equation was used to predict patterns of surface-crack growth under tension or bending fatigue loads. The equation was also used to correlate surface-crack fracture data for a brittle epoxy material within + or - 10 percent for a wide range of crack shapes and crack sizes.

Newman, J. C., Jr.↗
NASA NTRS1981

A crack-closure model for predicting fatigue crack growth under aircraft spectrum loading

The present paper is concerned with the development and application of an analytical model of cyclic crack growth that includes the effects of crack closure. The model was based on a concept like the Dugdale model, but was modified to leave plastically deformed material in the wake of the advancing crack tip. The model was used to correlate crack growth rates under constant-amplitude loading and to predict crack growth under aircraft spectrum loading on 2219-T851 aluminum alloy plate material. The predicted crack growth lives agreed well with experimental data. The ratio of predicted-to-experimental lives ranged from 0.66 to 1.48.

Newman, J. C., Jr.↗
NASA NTRS1980

A proposed standard round compact specimen for plane strain fracture toughness testing

A round, disk-shaped specimen is proposed as a standard test specimen for addition to ASTM Test for Plane-Strain Fracture Toughness of Metallic Materials (E 399-78A). The specimen is diametrically cracked, and loaded in the same way as the existing standard compact specimen. Tests and analyses were performed to verify that the proposed round compact specimen and associated stress intensity factor K solution are appropriate for a standard plane strain fracture toughness test. The use of the round compact specimen for other fracture tests is described.

Underwood, J. H.↗
NASA NTRS1980

Stress-intensity factors for internal surface cracks in cylindrical pressure vessels

The paper presents stress-intensity factors for a wide range of semi-elliptical surface cracks on the inside of pressurized cylinders. The ratio of crack depth to crack length ranged from 0.2 to 1; the ratio of crack depth to wall thickness ranged from 0.2 to 0.8; and the ratio of wall thickness to vessel radius was 0.1 to to 0.25. The stress-intensity factors were calculated by a three-dimensional finite-element method using singularity elements along the crack front and linear-strain elements elsewhere. An equation for the stress-intensity factors was obtained which applies over a wide range of configuration parameters and was within about 5 percent of the present results. A comparison was also made between the results and other analyses of internal surface cracks in cylinders. The results from a boundary-integral equation method were in agreement and those from another finite-element method were in fair agreement (+ or - 8 percent) with the results.

Newman, J. C., Jr.↗
NASA NTRS1980

Notch sensitivity of space shuttle tile materials

Tests were conducted at room temperature to determine the notch sensitivity of the thermal protection tile for the space shuttle. Two types of RSI tile were studied: LI-900 and LI-2200. Three point bend specimens were cut from discarded tiles in the in-plane (ip) and through-the-thickness (ttt) directions. They were tested with or without a sharp notch. The LI-900 (ip and ttt) specimens were not very notch sensitive, but the LI-2200 (ip and ttt) specimens were. The LI-2200 material showed about a 35 percent reduction in strength due to the presence of the notch. This reduction in strength should be considered in the design of mechanically fastened tile concepts.

Newman, J. C., Jr.↗
NASA NTRS1980

Fracture analysis of ductile materials

In the present paper, Newman's (1973) two-parameter fracture criterion is used to analyze failure of single-edge-crack tension specimens made of bolting steel and rotor steel, with thicknesses and widths of the same order. It is shown that for width-to-thickness ratios of roughly unity, the plastic-collapse stress is strongly influenced by the state of stress on the net section and the collapse stress is closer to the plane-strain value.

Newman, J. C., Jr.↗