Engineering topics
Ngan, Hio Tong
Publications and source records attributed to Ngan, Hio Tong.
Mechanistic Insights into Nonoxidative Ethanol Dehydrogenation on NiCu Single-Atom Alloys
Ethanol dehydrogenation presents a promising pathway towards the production of acetaldehyde, a valuable building block in chemicals production. Under non-oxidative conditions, the reaction is facilitated by supported Cu nanoparticles which afford reasonable activity and high selectivity. The stability issues associated with Cu nanoparticle sintering can be addressed by the addition of small amounts of Ni, which further boost reactivity while retaining selectivity. Despite the promise of NiCu single-atom alloys for non-oxidative ethanol dehydrogenation, little is known about the role of each component and the pathway of this mechanistically complex process. Herein, kinetic investigations from reactor tests identify C-H bond scission as the rate limiting step, while 1-hydroxyethyl is detected as the intermediate via IR spectroscopy. Temperature program desorption studies are employed to examine the effect of Ni coverage and to demonstrate that Ni atoms activate ethanol selectively at lower temperatures, resulting in higher acetaldehyde yield than pure Cu. Temperature program desorption experiments also reveal the spillover of intermediates from the Ni atom to neighboring Cu sites as a relevant step in the reaction pathway. Density functional theory calculations are used to investigate the 2 reaction energetics and to confirm that C-H bond scission is the initial reaction step, while a clear effect of H 2 partial pressure on the reaction pathway is realized. Further, counter to the expected behavior that all reaction steps take place on the Ni atoms, our degree of rate control analysis reveals that a mechanism involving spillover of the 1-hydroxyethyl intermediate from the Ni atom to the Cu surface, where it will dehydrogenate further, is more likely. Furthermore, our combined kinetic, spectroscopic, and theoretical approach sheds light on this complex reaction mechanism and represents a promising method for the understanding and designing of highly active, selective, and stable single-atom alloys for other multistep catalytic processes.
Achieving Ultra-High Selectivity to Hydrogen Production from Formic Acid on Pd–Ag Alloys
Palladium-silver based alloy catalysts have a great potential for CO-free hydrogen production from formic acid for fuel cell applications. However, the structural factors affecting the selectivity of formic acid decomposition is still debated. Herein, the decomposition pathways of formic acid on Pd-Ag alloys with different atomic configurations have been investigated to identify the alloy structures yielding high H 2 selectively. Several Pd x Ag 1-x surface alloys with various compositions were generated on a Pd(111) single crystal; their atomic distribution and electronic structure were determined by a combination of infrared reflection absorption spectroscopy (IRAS), X-ray photoelectron spectroscopy (XPS), and density functional theory (DFT). It was established that the Ag atoms with Pd neighbors are electronically altered, and the degree of alteration correlates with the number of nearest Pd. Temperature programmed reaction spectroscopy (TPRS) and DFT demonstrated that the electronically altered Ag domains create a new reaction pathway that selectively dehydrogenates formic acid. In contrast, Pd monomers surrounded by Ag are demonstrated to have a similar reactivity compared to pristine Pd(111), yielding CO and H 2 O in addition to the dehydrogenation products. Furthermore, they bind to the produced CO weaker than pristine Pd, demonstrating an enhancement in resistance to CO poisoning. This work therefore shows that surface Ag domains modified by interaction with subsurface Pd are the key active sites for selective decomposition of formic acid, while surface Pd atoms are detrimental for selectivity. Hence the decomposition pathways can be tailored for CO-free H 2 production on Pd-Ag alloy systems.
Decoding reactive structures in dilute alloy catalysts
Explore the source record for details and available documents.
Hydrogen Dissociation Controls 1-Hexyne Selective Hydrogenation on Dilute Pd-in-Au Catalysts
Increasing the selectivity of the catalytic hydrogenation of alkynes to alkenes is of major importance for the processing of petrochemicals and the production of fine chemicals. Achieving high selectivity for alkene formation at high conversions, however, remains a long-standing challenge in heterogeneous catalysis. Here, the mechanism and origin of the high selectivity of dilute Pd-in-Au catalysts has been studied by a combination of first-principles calculations, microkinetic simulations, and isotopic exchange hydrogenation experiments using Pd 0.04 Au 0.96 nanoparticles embedded in raspberry colloid-templated silica. The Pd is predominantly in the form of isolated atoms, only surrounded by Au atoms, based on prior studies. The simulations indicate that the rate-limiting process for 1-hexyne hydrogenation on Pd monomers in Au(111) is H 2 dissociation, which has a large free energy barrier of 0.86 eV at 363 K and 0.2 bar of H 2 . The C–H bond formation steps, on the other hand, proceed with lower barriers, which contrasts with previous studies of extended Pd catalysts. The microkinetic simulations identify the sizable H 2 dissociation barrier and the small barrier for the hydrogenation of 1-hexyne as key factors that lead to a high selectivity for the production of 1-hexene from 1-hexyne, even at high conversion. The unconventional H 2 dissociation limiting process in combination with the low coverage of weakly bound hydrocarbon intermediates explains the near-zero order of 1-hexyne found experimentally. Furthermore, the partial hydrogenation of 1-hexyne to form 1-hexene is shown to be an irreversible process from our isotopic exchange hydrogenation experiments and is explained by the strongly exothermic nature of the reaction. Diluting active species, like Pd, in a less active host metal, like Au, hence appears promising as a means of tuning the binding energy of reactants and altering reaction profiles, leading to distinct kinetic behavior for an optimal catalytic activity and selectivity. Furthermore, the combination of microkinetic modeling, density functional theory calculations, and isotopic exchange experiments is thus demonstrated to be an effective approach to modeling important catalytic phenomena.
Unraveling 1-Hexene Hydrogenation over Dilute Pd-in-Au Alloys
Dilute Pd-in-Au alloys are valuable materials for selectively hydrogenating alkynes and isomerizing alkenes. By diluting Pd in a Au host, the selectivity toward semihydrogenated alkene isomers can be significantly enhanced and the unfavorable overhydrogenation to alkanes is suppressed. However, a detailed mechanistic study on the origin of the enhanced alkene selectivity over dilute alloy catalysts is still missing. Here, we combine experiment and theory to unravel the reaction mechanism, identifying rate-limiting and selectivity-controlling steps in 1-hexene hydrogenation over dilute Pd-in-Au catalysts. Using isotope-exchange hydrogenation experiments, we show that 1-hexene and hydrogen over a bimetallic Pd4Au96 in silica catalyst preferentially form 1-hexene isomers, (trans and cis) 2- and 3-hexene and only a small amounts of hexane. The reaction is consistent with a Horiuti–Polanyi mechanism, similar to a monometallic Pd nanoparticle catalyst. Computation of the free-energy profiles for 1-hexene hydrogenation and isomerization over a single Pd atom in a Au surface using first principles calculations indicated that the isomerization of 1-hexene to 2-hexene is energetically favorable due to the relatively large barrier for H2 dissociation preventing hydrogenation to n-hexane. Microkinetic modeling established that H2 dissociation on the single-atom Pd sites and H spillover from these sites onto the Au host are rate-limiting and key in steering the selectivity of dilute Pd-in-Au alloys toward the hexene isomers. Furthermore, the mechanistic insights from this study contribute to the rational design of optimized dilute alloy catalysts for selective alkene isomerization.
Facilitating Hydrogen Dissociation over Dilute Nanoporous Ti–Cu Catalysts
The dissociation of H 2 is an essential elementary step in many industrial chemical transformations, typically requiring precious metals. Here, we report a hierarchical nanoporous Cu catalyst doped with small amounts of Ti (npTiCu) that increases the rate of H 2 –D 2 exchange by approximately one order of magnitude compared to the undoped nanoporous Cu (npCu) catalyst. The promotional effect of Ti was measured via steady-state H 2 –D 2 exchange reaction experiments under atmospheric pressure flow conditions in the temperature range of 300–573 K. Pretreatment with flowing H 2 is required for stable catalytic performance, and two temperatures, 523 and 673 K, were investigated. The experimentally determined H 2 –D 2 exchange rate is 5–7 times greater for npTiCu vs the undoped Cu material under optimized pretreatment and reaction temperatures. The H 2 pretreatment leads to full reduction of Cu oxide and partial reduction of surface Ti oxide species present in the as-prepared catalyst as demonstrated using in situ ambient pressure X-ray photoelectron spectroscopy and X-ray absorption spectroscopy. The apparent activation energies and pre-exponential factors measured for H 2 –D 2 exchange are substantially different for Ti-doped vs undoped npCu catalysts. Density functional theory calculations suggest that isolated, metallic Ti atoms on the surface of the Cu host can act as the active surface sites for hydrogen recombination. Furthermore, the increase in the rate of exchange above that of pure Cu is caused primarily by a shift in the rate-determining step from dissociative adsorption on Cu to H/D atom recombination on Ti-doped Cu, with the corresponding decrease in activation entropy that it produces.
Dynamical Study of Adsorbate-Induced Restructuring Kinetics in Bimetallic Catalysts Using the PdAu(111) Model System
The dynamic restructuring of bimetallic catalysts plays a crucial role in their catalytic activity and selectivity. In particular, catalyst pretreatment with species such as carbon monoxide and oxygen has been shown to be an effective strategy for tuning the surface composition and morphology. Mechanistic and kinetic understanding of such restructuring are fundamental to the chemistry and engineering of surface active sites but have remained challenging due to the large structural, chemical, and temporal degrees of freedom. Here, we combine time-resolved temperature-programmed infrared reflection absorption spectroscopy, ab initio thermodynamics, and machine-learning molecular dynamics to uncover previously unidentified timescale and kinetic parameters of in situ restructuring in Pd/Au(111), a highly relevant model system for dilute Pd-in-Au nanoparticle catalysts. The key innovation lies in utilizing CO not only as a chemically sensitive probe of surface Pd, but also as an agent that induces restructuring of the surface. Upon annealing in vacuum, as-deposited Pd islands became encapsulated by Au and partially dissolved into the subsurface, leaving behind isolated Pd monomers on the surface. Subsequent exposure to 0.1 mbar CO enabled Pd monomers to repopulate the surface up to 373 K, above which complete Pd dissolution occurred by 473 K, with apparent activation energies of 0.14 and 0.48 eV, respectively. Furthermore, these restructuring processes occurred over the span of ~1000 s at a given temperature. Such a minute-timescale dynamics not only elucidates the fluxional nature of alloy catalysts but also presents an opportunity to fine-tune the surface at moderate temperature and pressure conditions.
Replication Data for: Decoding reactive structures in dilute alloy catalysts
The data underlying this published work have been made publicly available in this repository as part of the IMASC Data Management Plan. This work was supported as part of the Integrated Mesoscale Architectures for Sustainable Catalysis (IMASC), an Energy Frontier Research Center funded by the U.S. Department of Energy, Office of Science, Basic Energy Sciences under Award # DE-SC0012573.
Dilute Alloys Based on Au, Ag, or Cu for Efficient Catalysis: From Synthesis to Active Sites
The development of new catalyst materials for energy-efficient chemical synthesis is critical as over 80% of industrial processes rely on catalysts, with many of the most energy-intensive processes specifically using heterogeneous catalysis. Catalytic performance is a complex interplay of phenomena involving temperature, pressure, gas composition, surface composition and structure over multiple length and time scales. In response to this complexity, the integrated approach to heterogeneous dilute-alloy catalysis reviewed here brings together materials synthesis, mechanistic surface chemistry, reaction kinetics, in-situ and operando characterization, and theoretical calculations in a coordinated effort to develop design principles to predict and improve catalytic selectivity. Dilute alloy catalysts—in which isolated atoms or small ensembles of the minority metal on the host metal lead to enhanced reactivity while retaining selectivity—are particularly promising as selective catalysts. Several dilute alloy materials using Au, Ag and Cu as the majority host element, including more recently introduced support-free nanoporous metals and oxide-supported nanoparticle "raspberry colloid templated (RCT)" materials, are reviewed for selective oxidation and hydrogenation reactions. Progress in understanding how such dilute alloy catalysts can be used to enhance selectivity of key synthetic reactions is reviewed, including quantitative scaling from model studies to catalytic conditions. The dynamic evolution of catalyst structure and composition studied in surface science and catalytic conditions and their relationship to catalytic function are also discussed, followed by advanced characterization and theoretical modeling that have been developed to determine the distribution of minority metal atoms at or near the surface. Furthermore, the integrated approach demonstrates the success of bridging the divide between fundamental knowledge and design of catalytic processes in complex catalytic systems, which can accelerate the development of new and efficient catalytic processes.
Replication Data for: Mechanistic and Electronic Insights into a Working NiAu Single-Atom Alloy Ethanol Dehydrogenation Catalyst
The data underlying this published work have been made publicly available in this repository as part of the IMASC Data Management Plan. This work was supported as part of the Integrated Mesoscale Architectures for Sustainable Catalysis (IMASC), an Energy Frontier Research Center funded by the U.S. Department of Energy, Office of Science, Basic Energy Sciences under Award # DE-SC0012573.
Mechanistic and Electronic Insights into a Working NiAu Single-Atom Alloy Ethanol Dehydrogenation Catalyst
Elucidation of reaction mechanisms and the geometric and electronic structure of the active sites themselves is a challenging, yet essential task in the design of new heterogeneous catalysts. Such investigations are best implemented via a multi-pronged approach that comprises ambient pressure catalysis, surface science, and theory. Herein, we employ this strategy to understand the workings of NiAu single-atom alloy (SAA) catalysts for the selective non-oxidative dehydrogenation of ethanol to acetaldehyde and hydrogen. The atomic dispersion of Ni is paramount for selective ethanol to acetaldehyde conversion, and we show that even the presence of small Ni ensembles in the Au surface results in the formation of undesirable byproducts via C-C scission. Spectroscopic, kinetic, and theoretical investigations of the reaction mechanism reveal that both C-H and O-H bond cleavage steps are kinetically relevant and single Ni atoms are confirmed as the active sites. X-ray absorption spectroscopy studies allow us to follow the charge of the Ni atoms in the Au host before, under, and after a reaction cycle. Specifically, in the pristine state the Ni atoms carry a partial positive charge which increases upon coordination to the electronegative oxygen in ethanol and decreases upon desorption. Furthermore, this type of oxidation state cycling during reaction is similar to the behavior of single-site homogenous catalysts. Given the unique electronic structure of many single-site catalysts, such a combined approach in which the atomic-scale catalyst structure and charge state of the single atom dopant can be monitored as a function of its reactive environment is a key step towards developing structure function relationships that inform the design of new catalysts.