Search NASA⌕ Search

Engineering topics

Nguyen, Khanh

Publications and source records attributed to Nguyen, Khanh.

12 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2022

Technology Maturation for Cloud Ice Radiometers

Global measurements of ice in clouds, both the amount and particle size distribution, are critically needed to reduce uncertainties in global climate models. The retrieval of this information is best achieved with a range of receiver channels across the submillimeter wave range. Advancement of low noise Indium Phosphide (InP) MMIC amplifier technology to 25-nm gate length enabled us to develop miniature submillimeter-wave receivers for a CubeSat scale instrument that achieves 6 km spatial resolution. We developed the 25-nm InP MMICs and radiometer receivers for 240, 310, 380, 670 GHz. The 25-nm InP MMIC technology was thermal vacuum tested to reduce risk for future space mission.

Duffy, Maxwell↗
NASA NTRS2019

Composites for Advanced Drive Systems, A Systems Analysis-Revolutionary Vertical Lift Technology (RVLT)

Rotorcraft propulsion systems are continually looking to improve power density; that is reducing weight and increasing power throughput. In order to advance rotorcraft propulsion system technology, NASA Glenn Research Center (NGRC) contracted Boeing Vertical Lift (Contract #NNA15AB12B, Task Order NNA16BE07T) to perform system level benefit assessments for incorporation of composite materials into rotorcraft transmission gear and shaft systems, in the rotating frame. In general, the environment inside a typical rotorcraft transmission is aggressive for typical composite materials. Design challenges in the rotating frame and related safety risks must be understood and accounted for in the design. Boeing developed a technical approach that evaluated a relatively large population of rotorcraft main transmissions. This technical approach took rotorcraft from various size classes and configurations and applied parametric weight estimating principles to assess the performance impact of composite hybrid technologies inside transmissions, in the rotating frame. Parametric weight estimates showed that composite hybrid technologies account for an average 9% weight savings over the baseline transmissions. More weight savings may be observed when accounting for quantity of transmissions in an aircraft configuration and benefits to airframe, landing gear, and fuel systems. A weight reduction of 595 lbs was calculated for NASA's Large Civil Tilt Rotor (LCTR2) by utilizing composite hybrid components inside the Prop-Rotor Transmission in the rotating frame and accounting for design changes to the airframe, landing gear, and fuel system. In order to develop composite hybrid technologies, sub-scale and full-scale testing should continue, building on the work that NGRC has begun. Design and testing efforts should focus on technical challenges, such as joint and attachment interfaces, temperature effects, inspection procedures, and fault detection. It is recommended to address technical challenges with targeted research and development efforts, conducted at relevant scale, prior to incorporating composite hybrid technologies within the rotating frame of helicopter transmissions.

Darmstadt, Patrick R.↗
NASA NTRS2004

Rotor Flapping Response to Active Control

Rotor active control using higher harmonic blade pitch has been proposed as a means to reduce both rotor radiated noise and airframe vibration and to enhance rotor performance. The higher harmonic input, however, can affect rotor thrust and cyclic flapping - the basic trim characteristics of the rotor. Some of the trim changes can negate the active control benefits. For example, wind tunnel test results of a full scale BO-105 rotor with individual-blade control indicate some rotor performance improvements, accompanied with changes in rotor trim, using two-per-rev blade pitch input. The observed performance benefits could therefore be a simple manifestation of the trim change rather than an efficient redistribution of the rotor airloads. More recently, the flight test of the BO-105 helicopter equip,ped with individual-blade-control actuators also reported trim changes whenever the two-per-rev blade pitch for noise reduction was activated. The pilot had to adjust the trim control to maintain the aircraft under a constant flight path. These two cases highlight the, importance of trim considerations in the application of active control to rotorcraft.

Nguyen, Khanh↗
NASA NTRS1996

Active Control of Helicopter Blade Stall

In an effort to expand the helicopter flight envelope, this analytical study proposes the concept of using high frequency blade pitch actuation to alleviate blade stall at high speed and/or high thrust flight conditions. The availability of high-frequency blade-mounted actuators has made this concept realizable. This study is carried out using the University of Maryland Advanced Rotorcraft Code (or UMARC), which employs state-of-the-art structural and aerodynamic modelings. The salient features of this code include the application of the finite element methods in both space and time domains, and the incorporation of an advanced unsteady aerodynamic and nonuniform inflow models. Preliminary results indicate that two-per-rev blade pitch control can reduce retreating blade stall for a rotor operating at high speed and high thrust flight condition. Current efforts concentrate on developing an automatic stall suppression system which employs a combination of higher harmonic blade pitch schedule.

Nguyen, Khanh↗
NASA NTRS1994

Dynamics of the McDonnell-Douglas Large Scale Dynamic Rig and dynamic calibration of the rotor balance

A shake test was performed on the Large Scale Dynamic Rig in the 40- by 80-Foot Wind Tunnel in support of the McDonnell Douglas Advanced Rotor Technology (MDART) Test Program. The shake test identifies the hub modes and the dynamic calibration matrix of the rotor balance. For hub mode identification, three configurations were tested: wind tunnel scale unlocked with dampers engaged and disengaged, and wind tunnel scale locked. Test data were analyzed with a multi-degree-of-freedom time domain algorithm to identify the modal properties of the hub modes. The damping of the low frequency hub modes (ground resonance modes) increases significantly with the wind tunnel dampers engaged. For dynamic calibration of the rotor balance, the shake test was performed only with the wind tunnel dampers engaged. The dynamic calibration matrix, computed from the shake test data using a least squares error method, is used to correct the five-per-rev vibratory balance readings. The corrections are large for the side force, moderate for the axial force and inplane hub moments, and small for the normal force.

Nguyen, Khanh↗
NASA NTRS1994

Computation of Loads on the McDonnell Douglas Advanced Bearingless Rotor

Computed results from UMARC and DART analyses are compared with the blade bending moments and vibratory hub loads data obtained from a full-scale wind tunnel test of the McDonnell Douglas five-bladed advanced bearingless rotor. The 5 per-rev vibratory hub loads data are corrected using results from a dynamic calibration of the rotor balance. The comparison between UMARC computed blade bending moments at different flight conditions are poor to fair, while DART results are fair to good. Using the free wake module, UMARC adequately computes the 5P vibratory hub loads for this rotor, capturing both magnitude and variations with forward speed. DART employs a uniform inflow wake model and does not adequately compute the 5P vibratory hub loads for this rotor.

Nguyen, Khanh↗
NASA NTRS1991

Applications of higher harmonic control to hingeless rotor systems

A comprehensive analytical formulation was developed to predict the vibratory hub loads of a helicopter rotor system in forward flight. This analysis is used to calculate the optimal higher harmonic control inputs and associated actuator power required to minimize these hub loads. The present formulation is based on a finite element method in space and time. A nonlinear time domain, unsteady aerodynamic model is used to obtain the airloads, and the rotor induced inflow is calculated using a nonuniform inflow model. Predicted vibratory hub loads are correlated with experimental data from a scale model rotor. Results of a parametric study on a hindgeless rotor show that blade flap, lag and torsion vibration characteristics, offset of blade center of mass from elastic axis, offset of elastic axis from quarter-chord axis, and blade thrust greatly affect the higher harmonic control actuator power requirement.

Nguyen, Khanh↗
NASA NTRS1990

Effects of higher harmonic control on rotor performance and control loads

An analytical study, based on an advanced Higher Harmonic Control (HHC) analysis for helicopter rotor systems, is carried out to investigate HHC application for rotor performance enhancement. The effects of HHC on stall characteristics of rotor and blade pitch-link loads when the system is configured to suppress vibration are also examined. For vibration control, simulated results indicate that HHC may promote early blade stall. Effects of blade torsion frequencies on HHC performance are moderate, and torsionally stiff blades require less actuator power than torsionally soft blades. For rotor performance improvement, a 3 to 5 percent reduction in rotor shaft power can be achieved with 2 deg of two-per-rev blade pitch control.

Nguyen, Khanh↗
NASA NTRS1990

Development of UMARC (University of Maryland Advanced Rotorcraft Code)

The University of Maryland Advanced Rotorcraft Code (UMARC) is a user-friendly, FEM-based comprehensive helicopter rotor simulation code of high numerical robustness and computational efficiency. UMARC formulates the rotor-fuselage equations using Hamilton's principle, and are discretized using finite elements in space and time. The FEM formulation allows the code to analyze a wide variety of rotor designs. Dynamic inflow modeling is used for unsteady wake inflow computations. Predicted stability, response, and blade-load data are validated with experimental data for several configurations, including representative articulated, hingeless, and bearingless rotors.

Bir, Gunjit↗
NASA NTRS1990

Application of higher harmonic control to hingeless rotor systems

A comprehensive analytical formulation has been dveloped to predict the vibratory hub loads of a helicopter rotor system in forward flight. The analysis is used to calculate the optimal higher harmonic control inputs and associated actuator power required to minimize these hub loads. The present formulation is based on a finite element method in space and time. A nonlinear time domain, unsteady aerodynamic model is used to obtain the airloads, and the rotor induced inflow is calculated using a nonuniform inflow model. Predicted vibratory hub loads are correlated with experimental data obtained from a scaled model rotor. Results of a parametric study on a hingeless rotor show that blade flap, lag and torsion vibration characteristics, offset of blade center of mass from elastic axis, offset of elastic axis from quarter-chord axis, and blade thrust greatly affect the higher harmonic control actuator power requirement.

Nguyen, Khanh↗
NASA NTRS1986

Use of a raster framebuffer in vision research

For the study of human and animal vision, the video framebuffer is the only technology that is capable of displaying two-dimensional images with precise control of contrast, luminance, and display timing. The video framebuffer also allows precise control of color. However, this device is not designed for precise psychophysical displays, and techniques must be developed to use them in this role. In order to be concrete, an RDS-3000 raster display system (Adage, 1982) is used which is hosted by a PDP-11/73 under the Venix operating system. The principles generalize to other machines. Where it clarifies the issues, the syntax of the software routines involved is shown.

Watson, Andrew B.↗