Engineering topics

Nguyen, Nhan T.

Publications and source records attributed to Nguyen, Nhan T..

At least 19 records

NASA NTRS2020

Model-Reference Adaptive Control of Distributed Lagrangian Infinite-Dimensional Systems Using Hamilton’s Principle

This paper presents a Hamilton's principle for distributed control of infinite-dimensional systems modeled by a distributed form of the Euler-Lagrange method. The distributed systems are governed by a system of linear partial differential equations in space and time. A generalized potential energy expression is developed that can capture most physical systems including those systems that have no spatial distribution. The Hamilton's principle is applied to derive distributed feedback control methods without resorting to the standard weak-form discretization approach to convert an infinite-dimensional systems to a finite-dimensional systems. It can be shown by the principle of least action that the distributed control synthesized by the Hamilton's principle is a minimum-norm control. A model-reference adaptive control framework is developed for distributed Lagrangian systems in the presence of uncertainty. The theory is demonstrated by an application of adaptive flutter suppression control of a flexible aircraft wing.

Nguyen, Nhan T.↗

NASA NTRS2020

Multi-Objective Gust Load Alleviation Control Designs for an Aeroelastic Wind Tunnel Demonstration Wing

This paper presents several control and gust disturbance estimation techniques applied to a mathematical model of a physical flexible wing wind tunnel model used in ongoing tests at the University of Washington Aeronautical Laboratory's Kirsten Wind Tunnel. Three methods of gust disturbance estimation are presented, followed by three control methods: LQG, Basic Multi-Objective (BMO), and a novel Multi-Objective Prediction Correction (MOPC) controller. The latter of which augments a multi-objective controller, and attempts to correct for errors in the disturbance estimate. A simplified linear simulation of the three controllers is performed and a simple MIMO stability and robustness assessment is performed. Then, the same controllers are simulated in a higher fidelity Simulink environment that captures sampling, saturation and noise effects. This preliminary analysis indicates that the BMO controller provides the best performance and largest stability margins.

Drew, Michael C.↗

NASA NTRS2020

Mode-Based Sensing and Actuation Techniques for Multi-Objective Flexible Aircraft Control

Intelligent sensing and actuation designs are explored as a means to improve performance of a gust load alleviation control design for a flexible wing aircraft equipped with wing-shaping control surfaces. The proposed techniques rely on identification of the dominant structural modes during specified flight conditions and uses them as a basis for sensor placement and actuator utilization. Specifically, a strategy for sensor placement is discussed that uses target mode shape capture as a mean to improve state estimation quality. A second strategy that reduces the number of wing-shaping control inputs using mode and objective-based shape functions as virtual input channels is also presented. Both techniques are demonstrated in simulation of a flexible wing transport aircraft utilizing a multi-objective control system designed to suppress flexible motion, minimize gust and maneuver load, and reduce drag.

Hashemi, Kelley E.↗

NASA NTRS2019

MRAC with Time-Varying Reference Model from Convex Combination

An extension of model reference adaptive control is presented that accommodates use of a time-varying reference model. Specifically, the reference model is taken to be a time-varying convex combination of two linear, time-invariant models. The design is intended to act as a way to smoothly transition between two different reference models without resorting to a scheduled switch. It also provides the ability to use an interpolated reference model when the plant is operating between design points. The time variation of the combination must satisfy some requirements to ensure stability but is otherwise user choice. Subject to these requirements, bounded tracking error behavior is demonstrated via Lyapunov stability analysis for the single-input, single-output, output feedback case. Tracking error convergence is asymptotic when time variation ceases. The proposed design is demonstrated in simulation of a numerical model.

Hashemi, Kelley E.↗

NASA NTRS2019

Aero-Structural Modeling of the Truss-Braced Wing Aircraft Using Potential Method with Correction Methods for Transonic Viscous Flow and Wing-Strut Interference Aerodynamics

This paper describes an aero-structural modeling method for the Transonic Truss-Braced Wing (TTBW) aircraft using VSPAERO. A vortex-lattice model of the TTBW aircraft is developed, and a transonic and viscous flow correction method is implemented in the VSPAERO models to account for transonic and viscous flow effects. A correction method for the wing-strut interference aerodynamics is developed and applied to the VSPAERO solver. Also, a structural dynamic finite-element model of the TTBW aircraft is developed. This finite-element model includes the geometric nonlinear effect due to the tension in the struts which cause a deflection dependent nonlinear stiffness. The VSPAERO models are coupled to the finite-element model to provide a rapid capability for aero-structural modeling and flutter analysis. A flight-optimized jig twist model is being developed and will be applied for the purpose of generating a full flight dynamic model of the TTBW aircraft.

Fugate, Jason↗

NASA NTRS2019

Extending A Correction Method for Unsteady Transonic Aerodynamics to Variable Camber Continuous Trailing Edge Flap

In this study, we have extended our correction method for transonic aerodynamics to baseline and variable camber continuous trailing edge (VCCTEF) geometries of super-critical airfoils at cruise conditions. This correction method modifies Theodorsen theory, which is based on incompressible potential flow over a flat plate. The method is partly based on CFD RANS simulations of oscillating NASA generic transport model (GTM) baseline cruise and VCCTEF airfoil geometries in pitch and shows promise for addressing transonic flutter problems of aeroelasticity. In the earlier study1, the Theodorsen functions were modulated with non-linear functions of Mach number, M, and reduced frequency, k, and thus the correction was demonstrated for the symmetrical NACA0012 airfoil. In the present study, the modulation functions are also allowed to account for the effects of camber and thickness of the airfoil. This is demonstrated by applying the correction method to various symmetric NACA00xx airfoil geometries (NACA001, NACA0002, NACA0012, NACA0015 and NACA0018), the NASA GTM super-critical baseline and VCCTEF airfoil geometries, e.g., the circular airfoil, VCCTEF222. First results indicate that the correction method accounts for a large variation of thickness of airfoils and camber. The present correction method will guide the development of a new state space model for the VCCTEF system and eventually a new transfer function that will be incorporated in a new aeroelastic framework leading to an appropriate transonic flutter model for use in the future aircraft systems in development under the NASA Advanced Air Transportation Technologies (AATT) project.

Kaul, Upender K.↗

NASA NTRS2019

Multi-Objective Optimal Control of the 6-DoF Aeroservoelastic Common Research Model with Aspect Ratio 13.5 Wing

A new 6-DoF aeroservoelastic (ASE) Common Research Model (CRM) provided by The Boeing Company with aspect ratio 13.5 and 17 control surfaces per wing is utilized to demonstrate combined tracking and optimal multi-objective control. The multi-objective controller is derived on the closed loop tracking controller, and utilizes state and gust estimates provided by an extended state observer. Various methods of model reduction useful for control and estimation are presented. A computationally efficient MATLAB/Simulink simulation is presented which includes actuator dynamics, rate and deflection saturation limits, and gust disturbance inputs. The platform is used to demonstrate excellent 6-DoF tracking control performance coupled with the multi-objective controller, which is shown to effectively reduce structural mode movement, wing root bending moment, and drag. State and gust estimation is also shown to perform well, even when derived and/or implemented with significantly fewer states than the original full-sized model.

Drew, Michael C.↗

NASA NTRS2019

Time-varying Weights in Multi-Objective Optimal Control for Flexible Wing Aircraft

A multi-objective optimal control technique is modified to accommodate changing cost function weights and is used to control a flexible wing aircraft model. Variation of the weights is used to adjust the relative importance of each objective according to either a prescribed function of time or of the state. Several techniques for obtaining a practical approximation to the optimal control solution are presented, and stability of a specific weight structure with the optimal controller is demonstrated. Functionality of the multi-objective control design with weight variation is demonstrated in simulation of a flexible wing transport aircraft and is shown to improve performance over the fixed weight version both at a constant flight condition and across changing flight conditions.

Hashemi, Kelley E.↗

NASA NTRS2019

A Correction Method for Unsteady Transonic Aerodynamics

This paper presents a new method for transonic pitching airfoils based on a RANS CFD study and the Theodorsen model of an oscillating pitching flat plate. This study quantifies the deviation of the lift coefficient predictions using CFD from that obtained using the Theodorsen model, which is based on the incompressible potential flow assumption. The present method corrects this theoretical model by modulating the Theodorsen functions by coefficient functions that depend on the reduced frequency and the Mach number. It is demonstrated that the modified theoretical model predicts lift coefficient in good agreement with the CFD results in the Mach number range from incompressible (M =0.2) to transonic (M =0.755) flow for a range of reduced frequencies typical of transonic flutter. The simulations are first validated by comparing pitching NACA0012 airfoil results with experimental results at transonic flight conditions, which establishes the requirements for a grid converged unsteady transonic solution. The hysteresis loop, Cl versus α, attains a grid independent solution that compares well with experiment. The present correction method will guide the development of a new state space model for the Variable Camber Continuous Trailing Edge Flap (VCCTEF) system and eventually a new transfer function that will be incorporated in a new aeroelastic framework leading to an appropriate transonic flutter model for use in the future aircraft systems in development under the NASA Advanced Air Transportation Technologies (AATT) project.

Kaul, Upender K.↗

NASA NTRS2019

Investigation of Anti-Phase Asymmetric Quiet Rotor Technology

The future of urban air mobility has a well-known tall pole challenge in the form of community acceptance which largely comes from the noise. This paper presents a proposed anti-phase rotor technology that could reduce noise sources such as blade vortex interaction noise. The anti-phase rotor technology includes a rotor design with various anti-phase alternating trailing edge patterns and a rotor design with an asymmetric blade tip. Four small-scale anti-phase rotors are fabricated by 3D printing for acoustic measurements conducted in a low-speed open-circuit wind tunnel to assess the effectiveness of the proposed anti-phase rotor technology. Preliminary test results appear to be promising and indicate that the anti-phase rotor designs could be a practical means of reducing blade vortex interactions and noise. The four tested anti-phase rotor designs have peak acoustic performance depending on the RPM and thrust which suggests improved performance through design optimization could be achieved for specific mission requirements.

Cramer, Nicholas B.↗

NASA NTRS2018

Time-Varying Modification of Reference Model for Adaptive Control with Performance Optimization

This paper presents a new adaptive control ap- proach that involves a performance optimization objective. The control synthesis involves the design of a performance optimizing adaptive controller from a subset of control inputs. The resulting effect of the performance optimizing adaptive controller is to modify the initial reference model into a time-varying reference model which satisfies the performance optimization requirement obtained from an optimal control problem. The time-varying reference model modification is accomplished by the real-time solutions of the time-varying Riccati and Sylvester equations coupled with the least-squares parameter estimation of the sen- sitivities of the performance metric. The effectiveness of the proposed method is demonstrated by an application of maneuver load alleviation control for a flexible aircraft.

Adaptive Control↗

NASA NTRS2018

Verification and Validation Challenges for Adaptive Flight Control of Complex Autonomous Systems

Autonomy of aerospace systems requires the ability for flight control systems to be able to adapt to complex uncertain dynamic environment. In spite of the five decades of research in adaptive control, the fact still remains that currently no adaptive control system has ever been deployed on any safety-critical or human-rated production systems such as passenger transport aircraft. The problem lies in the difficulty with the certification of adaptive control systems since existing certification methods cannot readily be used for nonlinear adaptive control systems. Research to address the notion of metrics for adaptive control began to appear in the recent years. These metrics, if accepted, could pave a path towards certification that would potentially lead to the adoption of adaptive control as a future control technology for safety-critical and human-rated production systems. Development of certifiable adaptive control systems represents a major challenge to overcome. Adaptive control systems with learning algorithms will never become part of the future unless it can be proven that they are highly safe and reliable. Rigorous methods for adaptive control software verification and validation must therefore be developed to ensure that adaptive control system software failures will not occur, to verify that the adaptive control system functions as required, to eliminate unintended functionality, and to demonstrate that certification requirements imposed by regulatory bodies such as the Federal Aviation Administration (FAA) can be satisfied. This presentation will discuss some of the technical issues with adaptive flight control and related V&V challenges.

Nguyen, Nhan T.↗

NASA NTRS2017

An Analysis of the Optimal Control Modification Method Applied to Flutter Suppression

Unlike basic Model Reference Adaptive Control (MRAC)l, Optimal Control Modification (OCM) has been shown to be a promising MRAC modification with robustness and analytical properties not present in other adaptive control methods. This paper presents an analysis of the OCM method, and how the asymptotic property of OCM is useful for analyzing and tuning the controller. We begin with a Lyapunov stability proof of an OCM controller having two adaptive gain terms, then the less conservative and easily analyzed OCM asymptotic property is presented. Two numerical examples are used to show how this property can accurately predict steady state stability and quantitative robustness in the presence of time delay, and relative to linear plant perturbations, and nominal Loop Transfer Recovery (LTR) tuning. The asymptotic property of the OCM controller is then used as an aid in tuning the controller applied to a large scale aeroservoelastic longitudinal aircraft model for flutter suppression. Control with OCM adaptive augmentation is shown to improve performance over that of the nominal non-adaptive controller when significant disparities exist between the controller/observer model and the true plant model.

aeroservoelasti↗

NASA NTRS2017

Aeroelastic Wing Shaping Using Distributed Propulsion

An aircraft has wings configured to twist during flight. Inboard and outboard propulsion devices, such as turbofans or other propulsors, are connected to each wing, and are spaced along the wing span. A flight controller independently controls thrust of the inboard and outboard propulsion devices to significantly change flight dynamics, including changing thrust of outboard propulsion devices to twist the wing, and to differentially apply thrust on each wing to change yaw and other aspects of the aircraft during various stages of a flight mission. One or more generators can be positioned upon the wing to provide power for propulsion devices on the same wing, and on an opposite wing.

Nguyen, Nhan T.↗

NASA NTRS2017

Performance Optimizing Adaptive Control with Time-Varying Reference Model Modification

This paper presents a new adaptive control approach that involves a performance optimization objective. The control synthesis involves the design of a performance optimizing adaptive controller from a subset of control inputs. The resulting effect of the performance optimizing adaptive controller is to modify the initial reference model into a time-varying reference model which satisfies the performance optimization requirement obtained from an optimal control problem. The time-varying reference model modification is accomplished by the real-time solutions of the time-varying Riccati and Sylvester equations coupled with the least-squares parameter estimation of the sensitivities of the performance metric. The effectiveness of the proposed method is demonstrated by an application of maneuver load alleviation control for a flexible aircraft.

Adaptive Control↗

NASA NTRS2017

Flight Control of Flexible Aircraft

This presentation presents an overview of flight control research for flexible high aspect wing aircraft in support of the NASA ARMD Advanced Air Transport Technology (AATT) project. It summarizes multi-objective flight control technology being developed for drag optimization, flutter suppression, and maneuver and gust load alleviation.

Aeroservoelasticity↗

NASA NTRS2017

Performance Optimizing Multi-Objective Adaptive Control with Time-Varying Model Reference Modification

This paper presents a new adaptive control approach that involves a performance optimization objective. The problem is cast as a multi-objective optimal control. The control synthesis involves the design of a performance optimizing controller from a subset of control inputs. The effect of the performance optimizing controller is to introduce an uncertainty into the system that can degrade tracking of the reference model. An adaptive controller from the remaining control inputs is designed to reduce the effect of the uncertainty while maintaining a notion of performance optimization in the adaptive control system.

Adaptive Control↗

NASA NTRS2017

Semi-Supervised Learning of Lift Optimization of Multi-Element Three-Segment Variable Camber Airfoil

This chapter describes a new intelligent platform for learning optimal designs of morphing wings based on Variable Camber Continuous Trailing Edge Flaps (VCCTEF) in conjunction with a leading edge flap called the Variable Camber Krueger (VCK). The new platform consists of a Computational Fluid Dynamics (CFD) methodology coupled with a semi-supervised learning methodology. The CFD component of the intelligent platform comprises of a full Navier-Stokes solution capability (NASA OVERFLOW solver with Spalart-Allmaras turbulence model) that computes flow over a tri-element inboard NASA Generic Transport Model (GTM) wing section. Various VCCTEF/VCK settings and configurations were considered to explore optimal design for high-lift flight during take-off and landing. To determine globally optimal design of such a system, an extremely large set of CFD simulations is needed. This is not feasible to achieve in practice. To alleviate this problem, a recourse was taken to a semi-supervised learning (SSL) methodology, which is based on manifold regularization techniques. A reasonable space of CFD solutions was populated and then the SSL methodology was used to fit this manifold in its entirety, including the gaps in the manifold where there were no CFD solutions available. The SSL methodology in conjunction with an elastodynamic solver (FiDDLE) was demonstrated in an earlier study involving structural health monitoring. These CFD-SSL methodologies define the new intelligent platform that forms the basis for our search for optimal design of wings. Although the present platform can be used in various other design and operational problems in engineering, this chapter focuses on the high-lift study of the VCK-VCCTEF system. Top few candidate design configurations were identified by solving the CFD problem in a small subset of the design space. The SSL component was trained on the design space, and was then used in a predictive mode to populate a selected set of test points outside of the given design space. The new design test space thus populated was evaluated by using the CFD component by determining the error between the SSL predictions and the true (CFD) solutions, which was found to be small. This demonstrates the proposed CFD-SSL methodologies for isolating the best design of the VCK-VCCTEF system, and it holds promise for quantitatively identifying best designs of flight systems, in general.

Intelligent Systems↗