Minimum Symbol Transition Density on Earth-to-Space Links
Earth-to-Space links are typically characterized by high symbol signal-to-noise ratio and low data rates.
data transition tracking loop symbol synchronizati↗
Engineering topics
Nguyen, T.
Publications and source records attributed to Nguyen, T..
Limitations on the Subcarrier Frequency-to-Symbol Rate Ratio
For space missions in which tracking the residual carrier is absolutely critical, the use of a subcarrier to separate the data from the residual carrier is the best way to maximize residual-carrier tracking performance.
subcarrier-to-symbol rate ratio↗
Prototype Backscatter Moessbauer Spectrometer for Measurement of Martian Surface Mineralogy
We have designed and successfully tested a prototype of a backscatter Moessbauer spectrometer (BaMS) targeted for use on the Martian surface to (1) determine oxidation states of iron, and (2) identify and determine relative abundances of iron-bearing mineralogies. No sample preparation is required to perform measurements; it is only necessary to bring sample and instrument into physical contact. The prototype meets our projected specification for a flight instrument in terms of mass, power, and volume. A Moessbauer spectrometer on the Martian surface would provide wide variety of information about the current state of the Martian surface, and this information is described.
Shelfer, T. D.↗
Combined backscatter Moessbauer spectrometer/x ray fluorescence analyzer (BaMS/XRF) for extraterrestrial surfaces
We have designed and tested a prototype combined backscatter Moessbauer spectrometer and x-ray fluorescence analyzer (BaMS/XRF). A space qualified instrument based on this design would be suitable for in-situ use on planetary missions to the surfaces of the Moon (Artemis and lunar outpost), Mars (MESUR), asteroids, or other solid solar system objects. The BaMS/XRF instrument is designed to be capable of concurrent sample analyses for the mineralogy of iron-bearing phases and elemental composition without the need for sample preparation.
Shelfer, T. D.↗
A Backscatter Moessbauer Spectrometer (BaMS) for use on Mars
The use of Moessbauer spectroscopy for in situ analysis on the surface of Mars was proposed and the design and implementation of a backscatter Moessbauer spectrometer (BaMS) instrument suitable for planetary missions to the surfaces of Mars (MESUR), the Moon (Artemis and lunar outpost), asteroids, or other solid solar system objects is discussed. The BaMS instrument is designed to be capable of analysis of a sample for the mineralogy of its iron-bearing phases without any sample preparation. A requirement of lander missions to Mars is instrumentation for in situ mineralogical analyses. Such analyses provide data needed for primary characterization as to the type of surface materials present and by inference the processes that formed and subsequently modified them. For purposes of providing diagnostic information about naturally occurring materials, the element iron is particularly important because it is abundant and multivalent (primarily 0, +2, and +3 oxidation states). Knowledge of the oxidation state of iron and its distribution among iron-bearing mineralogies tightly constrains the types of materials present. The pivotal role of iron was already recognized in 1978 by COMPLEX, who recommended development of flight instruments that would identify mineralogy and the oxidation state of iron in planetary surface materials. The near-term U.S. strategy for the exploration of Mars is the MESUR (Mars Environmental SURvey) program, which entails emplacement of a network of small, long-lived surface landers. For the Moon, BaMS was recommended as part of a three-instrument landed payload for the Artemis missions, targeted for 1997. BaMS would prospect for ilmenite, an oxygen resource material, and provide data to assess the maturity of lunar soil. Because instrumental characteristics are low mass, low volume, and low power consumption, BaMS is suitable for implementation on even small landers and rovers, as are being envisioned in MESUR and Artemis concepts. In addition to providing highly diagnostic data, a BaMS analyzer is inherently simple and, as is highly desirable for remote operation, no sample preparation is required.
Agresti, D. G.↗
The ogive as a RCS compact range standard
E- and H-plane radar cross section (RCS) patterns at 4 and 10 GHz are provided (based upon moment method calculations) for a perfectly conducting ogive to be used as a compact range verification standard. The dimensions of the ogive are 36 in. and 9.546 in. long with half tip angles of 15 deg and 20 deg, respectively. Comparison between the calculations and measurements are also provided.
Dominek, A.↗
Adaptive implicit-explicit and parallel element-by-element iteration schemes
Adaptive implicit-explicit (AIE) and grouped element-by-element (GEBE) iteration schemes are presented for the finite element solution of large-scale problems in computational mechanics and physics. The AIE approach is based on the dynamic arrangement of the elements into differently treated groups. The GEBE procedure, which is a way of rewriting the EBE formulation to make its parallel processing potential and implementation more clear, is based on the static arrangement of the elements into groups with no inter-element coupling within each group. Various numerical tests performed demonstrate the savings in the CPU time and memory.
Tezduyar, T. E.↗
The use of satellites in non-geostationary orbits for unloading geostationary communication satellite traffic peaks. Volume 1: Executive summary
The overall objective of this program was to assess the application, economic benefits, and technology and system implications of satellites in non-geostationary (non-GEO) orbits for off-loading peak traffic from GEO communications satellites. The study was organized into four technical tasks which are described in turn. They are: (1) concepts development; (2) system definition; (3) economic comparisons; and (4) technology requirements definition. Each of these tasks is defined in detail and the results of each are given.
Price, K.↗
The use of satellites in non-goestationary orbits for unloading geostationary communication satellite traffic peaks. Volume 2: Technical report
The part of the geostationary (GEO) orbital arc used for United States domestic fixed, communications service is rapidly becoming filled with satellites. One of the factors currently limiting its utilization is that communications satellites must be designed to have sufficient capacity to handle peak traffic leads, and thus are under utilized most of the time. A solution is to use satellites in suitable non-geostationary orbits to unload the traffic peaks. Three different designs for a non-geostationary orbit communications satellite system are presented for the 1995 time frame. The economic performance is analyzed and compared with geostationary satellites for two classes of service, trunking and customer premise service. The result is that the larger payload of the non-geostationary satellite offsets the burdens of increased complexity and worse radiation environment to give improved economic performance. Depending on ground terminal configuration, the improved economic performance of the space segment may be offset by increased ground terminal expenses.
Price, K.↗
Satellite analog FDMA/FM to digital TDMA conversion
The results of a study which investigated design issues regarding the use of analog to digital (A/D) conversion on board a satellite are presented. The need for A/D, and of course D/A as well, conversion arose from a satellite design which required analog FDMA/FM up and down links to/from a digitally modulated intersatellite link. There are also some advantages when one must interconnect a large number of various spot beams which are using analog, and therefore cannot take advantage of SS/TDMA switching among the beams, thus resulting in low fill factors. Various tradeoffs were performed regarding the implementation of on-board A/D processing, including mass, power, and costs. The various technologies which were considered included flash ADCs, surface acoustic wave (SAW) devices, and digital signal processing (DSP) chips. Impact analyses were also performed to determine the effect on ground stations to convert to digital if the A/D approach were not implemented.
Driggers, T.↗
Evaluation of automated decision making methodologies and development of an integrated robotic system simulation: Study results
The implementation of a generic computer simulation for manipulator systems (ROBSIM) is described. The program is written in FORTRAN, and allows the user to: (1) Interactively define a manipulator system consisting of multiple arms, load objects, targets, and an environment; (2) Request graphic display or replay of manipulator motion; (3) Investigate and simulate various control methods including manual force/torque and active compliance control; and (4) Perform kinematic analysis, requirements analysis, and response simulation of manipulamotion. Previous reports have described the algorithms and procedures for using ROBSIM. These reports are superseded and additional features which were added are described. They are: (1) The ability to define motion profiles and compute loads on a common base to which manipulator arms are attached; (2) Capability to accept data describing manipulator geometry from a Computer Aided Design data base using the Initial Graphics exchange Specification format; (3) A manipulator control algorithm derived from processing the TV image of known reference points on a target; and (4) A vocabulary of simple high level task commands which can be used to define task scenarios.
Haley, D. C.↗
Evaluation of automated decisionmaking methodologies and development of an integrated robotic system simulation. Appendix A: ROBSIM user's guide
The purpose of the Robotics Simulation Program is to provide a broad range of computer capabilities to assist in the design, verification, simulation, and study of robotics systems. ROBSIM is program in FORTRAN 77 for use on a VAX 11/750 computer under the VMS operating system. This user's guide describes the capabilities of the ROBSIM programs, including the system definition function, the analysis tools function and the postprocessor function. The options a user may encounter with each of these executables are explained in detail and the different program prompts appearing to the user are included. Some useful suggestions concerning the appropriate answers to be given by the user are provided. An example user interactive run in enclosed for each of the main program services, and some of the capabilities are illustrated.
Haley, D. C.↗
Evaluation of automated decisionmaking methodologies and development of an integrated robotic system simulation. Appendix B: ROBSIM programmer's guide
The purpose of the Robotic Simulation (ROBSIM) program is to provide a broad range of computer capabilities to assist in the design, verification, simulation, and study of robotic systems. ROBSIM is programmed in FORTRAM 77 and implemented on a VAX 11/750 computer using the VMS operating system. The programmer's guide describes the ROBSIM implementation and program logic flow, and the functions and structures of the different subroutines. With the manual and the in-code documentation, an experienced programmer can incorporate additional routines and modify existing ones to add desired capabilities.
Haley, D. C.↗
Development of mathematical techniques for the analysis of remote sensing data
There are no author-identified significant results in this report.
Decell, H. P., Jr.↗