Search NASA⌕ Search

Engineering topics

Nguyen, Thien D.

Publications and source records attributed to Nguyen, Thien D..

6 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Tetrel Bond-Mediated Photophysical Modulation and Fluoride Recognition in Carbazole-Organosilanes

Silicon-centered orbitals are typically regarded as electronically inert in donor–acceptor systems. Here, we show that silole-based carbazole–silane architectures can render these orbitals electronically relevant, enabling modulation of excited-state behavior and anion-responsive photophysics. Two carbazole–Dipp–silanes exhibit identical carbazole-localized LE singlet emission in solution yet diverge markedly in the solid state: one compound displays a broad long-wavelength emission band in the prompt spectrum and enhanced long-lived emission consistent with a triplet-derived excited state, likely arising from a combination of intramolecular structural locking and solid-state packing effects, whereas the more flexible analogue remains predominantly LE-emissive. Fluoride coordination further differentiates the two systems, producing ratiometric red-shifted emission in one case and fluorescence quenching in the other through a fully reversible coordination process. These results identify σ*(Si–Ar) orbitals as tunable contributors to excited-state landscapes in organosilane luminophores and suggest a broader design strategy for controlling excited-state behavior in tetrel-based photofunctional systems.

Haque, Md Hasanul↗
DOE OSTI2024

Ultrasonic Nondestructive Diagnosis of Cylindrical Batteries Under Various Charging Rates

Lithium-ion batteries have been used increasingly as electrochemical energy storage systems for electronic devices and vehicles. It is important to accurately estimate the state of charge (SoC) of a battery management system to control the battery operation to optimize performance, lifetime, and safety. The current work experimentally leverages ultrasonic diagnostic technology to investigate the SoC of lithium-ion batteries during the charge/discharge processes. A cylindrical-type nickel-cobalt-aluminum (NCA)–based 2500mAh 20A (INR18650-25R) battery was used for ultrasonic measurements with various charge/discharge rates of C/10.4, C/5.2, and C/1.3 at constant currents. The ultrasonic signals were analyzed for extracting wave velocity and wave attenuation. For all the testing rates, wave velocity increased in the charge process and decreased in the discharge process. Further, velocity profiles corresponding to lower rates of C/10.4 and C/5.2 exhibited primary peaks at the maximum SoCs, whereas the absolute wave velocity of C/1.3 rate showed primary peaks that occurred slightly after the SoC peak, indicating a delayed maximum Young's modulus. The wave attenuation computed for the C/10.4 rate had local maxima in the charge and discharge processes and depicted negative correlations with SoC, ranging from 0% to 18%, and positive correlations with SoC from 18% to 85%. On the other hand, the wave attenuation curves of the C/1.3 rate showed no local peaks and had negative correlations with SoC, ranging from 0% to 28%, and positive correlations with SoC ranging from 28% to 53%.

25 ENERGY STORAGE↗
DOE OSTI2023

Numerical Study of Liquid Piston Compression Using Large-Eddy Simulation and Volume-of-Fluid Approach

Efforts to increase the efficiency of residential and commercial air conditioners and heat pumps have demonstrated that the compressor accounts for most of the system’s electrical energy usage. Therefore, the efficiency of this component should be improved to reduce its energy usage. The US Department of Energy’s Oak Ridge National Laboratory developed a near-isothermal liquid piston compressor (LPC) that uses propylene glycol (PG) to compress CO2. This report presents numerical studies of the LPC in which the compression chamber fills with injected PG from the bottom inlet. Numerical simulations were performed using the large-eddy simulation (LES) with the wall-adapting local eddy-viscosity (WALE) subgrid-scale model coupled with the multiphase volume-of-fluid (VOF) model to simulate the transient interface between gas and liquid and to capture the heat and mass transfer within the compression chamber. In this effort, effects of boundary conditions applied to the LES-VOF calculations (e.g., no wall, an adiabatic wall, and a wall with a heat flux subscribed) to the overall pressure and temperature of CO2 gas as well as the transient evolution of flow and heat transfer evolution within the compression chamber are investigated and discussed. It was found that the LES calculation with no wall have shown no dynamical flow patterns and the volume-averaged temperature of CO2 increased from 305 to 392.7 K, while LES calculations with a constant wall temperature or a wall heat flux had similar increases of CO2 temperatures. Results of LES simulation using a wall heat flux showed different stages in the compression process and revealed dynamical formation and interaction of CO2 gas layers and circulation flow patterns within the chamber that contribute to the overall heat transfer between the solid wall, gas, and liquid surface in the compressor.

Nguyen, Thien D.↗