Engineering topics

Nieh, T. G.

Publications and source records attributed to Nieh, T. G..

3 records

DOE OSTI2021

Unravel unusual hardening behavior of a Pd–Ni–P metallic glass in its supercooled liquid region

Monolithic metallic glasses often exhibit work softening induced by high atom mobility in the supercooled liquid region in tension. In this work, we report an unusual viscous flow of the Pd 42.5 Ni 42.5 P 15 metallic glass in its supercooled liquid region, which is characterized by a remarkable hardening behavior with decent plasticity during tension. To unravel the causes of this unusual hardening, we conducted structural and thermodynamic analyses by employing several experiments, including dynamic mechanical analysis, differential scanning calorimetry, high-resolution transmission electron microscopy, and in situ heating synchrotron high-energy x-ray diffraction. It was found that the unusual hardening behavior was attributed to structural ordering during deformation, rather than nanocrystallization or structural relaxation observed, sometimes, in metallic glasses deformed in supercooled liquid region. We also incorporated an additional work hardening region in the modified deformation map for metallic glasses.

36 MATERIALS SCIENCE↗

NASA NTRS1992

Superplastic forming of ceramic insulation

Superplasticity has been demonstrated in many fine-grained structural ceramics and ceramic composites, including yttria-stabilized tetragonal zirconia polycrystal (YTZP), alumina, and Al2O3-reinforced zirconia (Al2O3/YTZ) duplex composites and SiC-reinforced Si3N4. These superplastic ceramics obviously offer the potential benefit of forming net shape or near net shape parts. This could be particularly useful for forming complicated shapes that are difficult to achieve using conventional forming techniques, or require elaborate, subsequent machining. In the present study, we successfully demonstrated the following: (1) superplastic 3Y-TXP and 20 percent Al2O3/YTZ composite have for the first time been successfully deformed into hemispherical caps via a biaxial gas-pressure forming technique; (2) no experimental difficulty was encountered in applying the required gas pressures and temperatures to achieve the results, thus, it is certain that higher rates of deformation than those presented in this study will be possible by using the current test apparatus at higher temperatures and pressures; and (3) an analytical model incorporating material parameters, such as variations during forming in the strain rate sensitivity exponent and grain growth-induced strain hardening, is needed to model accurately and therefore precisely control the biaxial gas-pressure forming of superplastic ceramics. Based on the results of this study, we propose to fabricate zirconia insulation tubes by superplastic extrusion of zirconia polycrystal. This would not only reduce the cost, but also improve the reliability of the tube products.

Nieh, T. G.↗

NASA NTRS1985

Microstructure and fracture in SiC whisker reinforced 2124 aluminum composite

The microstructures of extruded and hot-rolled 2124 Al-15 percent (by weight) SiC whisker composites have been investigated, experimentally. Among the specific factors studied were: the strength of the whisker-matrix interfaces; (2) the presence of oxides; (3) the presence of defective whiskers; (4) and the presence of distribution of intermetallic compounds, impurities in the SiC(w) powder, and microstructural inhomogeneities. Modifications in the microstructure of the SiC/AL composites due to hot rolling and extrusion are illustrated in a series of microphotographs. It was found that hot rolling along the axis of extrusion was associated with some types of whisker damage, while the whiskers still retain their original orientation. Hot-rolling perpendicular to the axis of extrusion, however, tended to rotate the whiskers and produced a nearly isotropic material. Whisker free zones were virtually eliminated or reduced in size by hot rolling. In situ Auger fractography of the composite showed that the interfacial bonding between the SiC and the Al matrix was good and that Al2O2 had no significant influence on the fracture mechanics of the composite.

Nieh, T. G.↗