Nikjooy, M. | Search NASA

NASA NTRS1993

Flow interaction experiment. Volume 1: Aerothermal modeling, phase 2

An experimental and computational study is reported for the flow of a turbulent jet discharging into a rectangular enclosure. The experimental configurations consisting of primary jets only, annular jets only, and a combination of annular and primary jets are investigated to provide a better understanding of the flow field in an annular combustor. A laser Doppler velocimeter is used to measure mean velocity and Reynolds stress components. Major features of the flow field include recirculation, primary and annular jet interaction, and high turbulence. A significant result from this study is the effect the primary jets have on the flow field. The primary jets are seen to create statistically larger recirculation zones and higher turbulence levels. In addition, a technique called marker nephelometry is used to provide mean concentration values in the model combustor. Computations are performed using three levels of turbulence closures, namely k-epsilon model, algebraic second moment (ASM), and differential second moment (DSM) closure. Two different numerical schemes are applied. One is the lower-order power-law differencing scheme (PLDS) and the other is the higher-order flux-spline differencing scheme (FSDS). A comparison is made of the performance of these schemes. The numerical results are compared with experimental data. For the cases considered in this study, the FSDS is more accurate than the PLDS. For a prescribed accuracy, the flux-spline scheme requires a far fewer number of grid points. Thus, it has the potential for providing a numerical error-free solution, especially for three-dimensional flows, without requiring an excessively fine grid. Although qualitatively good comparison with data was obtained, the deficiencies regarding the modeled dissipation rate (epsilon) equation, pressure-strain correlation model, and the inlet epsilon profile and other critical closure issues need to be resolved before one can achieve the degree of accuracy required to analytically design combustion systems.

Nikjooy, M.↗

NASA NTRS1993

Flow interaction experiment. Volume 2: Aerothermal modeling, phase 2

An experimental and computational study is reported for the flow of a turbulent jet discharging into a rectangular enclosure. The experimental configurations consisting of primary jets only, annular jets only, and a combination of annular and primary jets are investigated to provide a better understanding of the flow field in an annular combustor. A laser Doppler velocimeter is used to measure mean velocity and Reynolds stress components. Major features of the flow field include recirculation, primary and annular jet interaction, and high turbulence. A significant result from this study is the effect the primary jets have on the flow field. The primary jets are seen to create statistically larger recirculation zones and higher turbulence levels. In addition, a technique called marker nephelometry is used to provide mean concentration values in the model combustor. Computations are performed using three levels of turbulence closures, namely k-epsilon model, algebraic second moment (ASM), and differential second moment (DSM) closure. Two different numerical schemes are applied. One is the lower-order power-law differencing scheme (PLDS) and the other is the higher-order flux-spline differencing scheme (FSDS). A comparison is made of the performance of these schemes. The numerical results are compared with experimental data. For the cases considered in this study, the FSDS is more accurate than the PLDS. For a prescribed accuracy, the flux-spline scheme requires a far fewer number of grid points. Thus, it has the potential for providing a numerical error-free solution, especially for three-dimensional flows, without requiring an excessively fine grid. Although qualitatively good comparison with data was obtained, the deficiencies regarding the modeled dissipation rate (epsilon) equation, pressure-strain correlation model, and the inlet epsilon profile and other critical closure issues need to be resolved before one can achieve the degree of accuracy required to analytically design combustion systems.

Nikjooy, M.↗

NASA NTRS1993

Fuel injector: Air swirl characterization aerothermal modeling, phase 2, volume 1

A well integrated experimental/analytical investigation was conducted to provide benchmark quality relevant to a prefilming type airblast fuel nozzle and its interaction with the combustor dome air swirler. The experimental investigation included a systematic study of both single-phase flows that involved single and twin co-axial jets with and without swirl. A two-component Phase Doppler Particle Analyzer (PDPA) was used to document the interaction of single and co-axial air jets with glass beads that simulate nonevaporating spray and simultaneously avoid the complexities associated with fuel atomization processes and attendant issues about the specification of relevant boundary conditions. The interaction of jets with methanol spray produced by practical airblast nozzle was also documented in the spatial domain of practical interest. Model assessment activities included the use of three turbulence models (k-epsilon, algebraic second moment (ASM), and differential second moment (DSM)) for the carrier phase, deterministic or stochastic Lagrangian treatment of the dispersed phase, and advanced numerical schemes. Although qualitatively good comparison with data was obtained for most of the cases investigated, the model deficiencies in regard to modeled dissipation rate transport equation, single length scale, pressure-strain correlation, and other critical closure issues need to be resolved before one can achieve the degree of accuracy required to analytically design combustion systems.

Nikjooy, M.↗

NASA NTRS1993

Fuel Injector: Air swirl characterization aerothermal modeling, phase 2, volume 2

A well integrated experimental/analytical investigation was conducted to provide benchmark quality data relevant to prefilming type airblast fuel nozzle and its interaction with combustor dome air swirler. The experimental investigation included a systematic study of both single-phase flows that involved single and twin co-axial jets with and without swirl. A two-component Phase Doppler Particle Analyzer (PDPA) equipment was used to document the interaction of single and co-axial air jets with glass beads that simulate nonevaporating spray and simultaneously avoid the complexities associated with fuel atomization processes and attendant issues about the specification of relevant boundary conditions. The interaction of jets with methanol spray produced by practical airblast nozzle was also documented in the spatial domain of practical interest. Model assessment activities included the use of three turbulence models (k-epsilon, algebraic second moment (ASM) and differential second moment (DSM)) for the carrier phase, deterministic or stochastic Lagrangian treatment of the dispersed phase, and advanced numerical schemes. Although qualitatively good comparison with data was obtained for most of the cases investigated, the model deficiencies in regard to modeled dissipation rate transport equation, single length scale, pressure-strain correlation, and other critical closure issues need to be resolved before one can achieve the degree of accuracy required to analytically design combustion systems.

Nikjooy, M.↗

NASA NTRS1991

A second-order modeling study of confined swirling flow

A numerical study of a confined strong swirling flow is presented. Computations are performed using a differential second-moment closure. The effect of inlet dissipation rate on calculated mean and turbulence fields is investigated. Two pressure-strain models with various model constants are examined to demonstrate their influences on the predicted results. Finally, comparison of the differential second-moment calculation is made with algebraic second-moment results to determine a better suited model for complex swirling flows.

Nikjooy, M.↗

NASA NTRS1991

Calculations of particle-laden flows by second-moment closures

A differential second-moment closure is applied to calculate nonswirling turbulent particle-laden jet flow. The closure is effected by extending constant-density single-phase turbulence models to the continuous (carrier) phase of two-phase flow. The dispersed (discrete) phase is treated by stochastic-Lagrangian technique. To reduce the effects of numerical (false) diffusion on the predicted results, a higher order differencing scheme, namely the flux-spline, is employed. In addition, an experimental study is conducted to provide data of good quality, especially near the inlet, for model assessment. The experiment consists of a confined coaxial jet flow of air with glass beads. The beads' diameter is 105 microns and is injected from the inner jet with a mass loading ratio of 0.9. The computed results are in good agreement with experimental data, especially for the carrier phase. However, the predicted turbulence fluctuations associated with the discrete phase are lower than the data at the downstream region of the flow field.

Nikjooy, M.↗

NASA NTRS1990

Calculation of turbulent three-dimensional jet-induced flow in a rectangular enclosure

The application of a flux-spline scheme to three-dimensional fluid flow is reported. A comparison is made of the performance of this scheme with that of the Power-law differencing scheme. The numerical results are compared with experimental data. For the problem considered in this study, the flux-spline scheme is more accurate than the Power-law. For a prescribed accuracy, the flux-spline scheme requires a far fewer number of grid points. Thus, it has the potential of providing a numerical error-free solution, especially for three-dimensional flows, without requiring an excessively fine grid.

Nikjooy, M.↗

NASA NTRS1989

A numerical and experimental study of coaxial jets

An algebraic stress model and the standard k-epsilon model is applied to predict the mean and turbulence quantities for axisymmetric, nonswirling coaxial jets without confinement. To investigate the effects of numerical (false) diffusion on the predicted results, three different discretization schemes, namely, hybrid, power-law, and the flux-spline, are employed. In addition, an experimental study is conducted to provide data of good quality, especially near the inlet, for model assessment. The results show that the use of the algebraic stress model leads to better agreement between the numerical results and experimental data.

Nikjooy, M.↗

NASA NTRS1989

A numerical and experimental study of confined swirling jets

A numerical and experimental study of a confined strong swirling flow is presented. Detailed velocity measurements are made using a two-component laser Doppler velocimeter (LDV) technique. Computations are performed using a differential second-moment (DSM) closure. The effect of inlet dissipation rate on calculated mean and turbulence fields is investigated. Various model constants are employed in the pressure-strain model to demonstrate their influences on the predicted results. Finally, comparison of the DSM calculations with the algebraic second-monent (ASM) closure results shows that the DSM is better suited for complex swirling flow analysis.

Nikjooy, M.↗

NASA NTRS1989

On the modelling of scalar and mass transport in combustor flows

Results are presented of a numerical study of swirling and nonswirling combustor flows with and without density variations. Constant-density arguments are used to justify closure assumptions invoked for the transport equations for turbulent momentum and scalar fluxes, which are written in terms of density-weighted variables. Comparisons are carried out with measurements obtained from three different axisymmetric model combustor experiments covering recirculating flow, swirling flow, and variable-density swirling flow inside the model combustors. Results show that the Reynolds stress/flux models do a credible job of predicting constant-density swirling and nonswirling combustor flows with passive scalar transport. However, their improvements over algebraic stress/flux models are marginal. The extension of the constant-density models to variable-density flow calculations shows that the models are equally valid for such flows.

Nikjooy, M.↗

NASA NTRS1988

K-epsilon turbulence model assessment with reduced numerical diffusion for coaxial jets

A numerical study has been conducted to evaluate the performance of the k-epsilon turbulence model for axisymmetric, unconfined, swirling, and nonswirling coaxial jet flows. Two lower order schemes, hybrid and power-law, and two higher order schemes, flux-spline and bounded skew upwind differencing, were employed in this investigation. The predicted results indicate that the higher order numerical schemes have greater potential for future model improvements and complex flow calculations in terms of storage, accuracy, and execution time. For the nonswirling flow, computations using an algebraic stress model have also been presented.

Nikjooy, M.↗

NASA NTRS1987

Aerothermal modeling program. Phase 2, element B: Flow interaction experiment

NASA has instituted an extensive effort to improve the design process and data base for the hot section components of gas turbine engines. The purpose of element B is to establish a benchmark quality data set that consists of measurements of the interaction of circular jets with swirling flow. Such flows are typical of those that occur in the primary zone of modern annular combustion liners. Extensive computations of the swirling flows are to be compared with the measurements for the purpose of assessing the accuracy of current physical models used to predict such flows.

Nikjooy, M.↗

NASA NTRS1986

Aerothermal modeling program, phase 2. Element B: Flow interaction experiment

The design process was improved and the efficiency, life, and maintenance costs of the turbine engine hot section was enhanced. Recently, there has been much emphasis on the need for improved numerical codes for the design of efficient combustors. For the development of improved computational codes, there is a need for an experimentally obtained data base to be used at test cases for the accuracy of the computations. The purpose of Element-B is to establish a benchmark quality velocity and scalar measurements of the flow interaction of circular jets with swirling flow typical of that in the dome region of annular combustor. In addition to the detailed experimental effort, extensive computations of the swirling flows are to be compared with the measurements for the purpose of assessing the accuracy of current and advanced turbulence and scalar transport models.

Nikjooy, M.↗

NASA NTRS1986

Modelling of jet- and swirl-stabilized reacting flows in axisymmetric combustors

Turbulent nonreactive and reactive flows with and without swirl are analyzed, with particular attention given to the flow fields of a gas-fueled nonpremixed swirl-stabilized combustor and a premixed opposed-jet combustor. Local mean flow properties, including velocity, temperature, and major species concentrations, are calculated by solving numerically the governing partial differential equations with associated submodels for turbulence and combustion. The results of the study indicate that the constant-density k-epsilon turbulence model provides a satisfactory representation of the aerodynamics in most practical combustor flows. The exception is the case of jet-stabilized combustor flow, due to the fact that the k-epsilon model cannot replicate the highly dissipative phenomenon found in such flows.

Nikjooy, M.↗

NASA NTRS1985

A comparison of three algebraic stress closures for combustor flow calculations

A comparison is made of the performance of two locally nonequilibrium and one equilibrium algebraic stress closures in calculating combustor flows. Effects of four different pressure-strain models on these closure models are also analyzed. The results show that the pressure-strain models have a much greater influence on the calculated mean velocity and turbulence field than the algebraic stress closures, and that the best mean strain model for the pressure-strain terms is that proposed by Launder, Reece and Rodi (1975). However, the equilibrium algebraic stress closure with the Rotta return-to-isotropy model (1951) for the pressure-strain terms gives as good a correlation with measurements as when the Launder et al. mean strain model is included in the pressure-strain model. Finally, comparison of the calculations with the standard k-epsilon closure results show that the algebraic stress closures are better suited for simple turbulent flow calculations.

Nikjooy, M.↗

NASA NTRS1983

Modeling of Fluctuating Mass Flux in Variable Density Flows

The approach solves for both Reynolds and Favre averaged quantities and calculates the scalar pdf. Turbulent models used to close the governing equations are formulated to account for complex mixing and variable density effects. In addition, turbulent mass diffusivities are not assumed to be in constant proportion to turbulent momentum diffusivities. The governing equations are solved by a combination of finite-difference technique and Monte-Carlo simulation. Some preliminary results on simple variable density shear flows are presented. The differences between these results and those obtained using conventional models are discussed.

So, R. M. C.↗