Search NASA⌕ Search

Engineering topics

Nikroo, A.

Publications and source records attributed to Nikroo, A..

At least 73 records · Page 4

Review of hydro-instability experiments with alternate capsule supports in indirect-drive implosions on the National Ignition Facility

Hydrodynamic instability growth of capsule support membranes (or “tents”) has been recognized as one of the major contributors to the performance degradation in high-compression plastic capsule implosions at the National Ignition Facility (NIF). The capsules were supported by tents because the nominal 10-μm diameter fill tubes were not strong enough to support capsules by themselves in indirect-drive implosions on NIF. After it was recognized that the tents had a significant impact of implosion's stability, new alternative support methods were investigated. While some of these methods completely eliminated tent, other concepts still used tents, but concentrated on mitigating their impact. The tent-less methods included “fishing pole” reinforced fill tubes, cantilevered fill tubes, and thin-wire “tetra cage” supports. In the “fishing pole” concept, a 10-μm fill tube was inserted inside 30-μm fill tube for extra support with the connection point located 300 μm away from the capsule surface. The cantilevered fill tubes were supported by 12-μm thick SiC rods, offset by up to 300 μm from the capsule surfaces. In the “tetra-cage” concept, 2.5-μm thick wires (carbon nanotube yarns) were used to support a capsule. Other concepts used “polar tents” and a “foam-shell” to mitigate the effects of the tents. The “polar tents” had significantly reduced contact area between the tents and the capsule compared to the nominal tents. In the “foam-shell” concept, a 200-μm thick, 30 mg/cc SiO 2 foam layer was used to offset the tents away from the capsule surface in an attempt to mitigate their effects. These concepts were investigated in x-ray radiography experiments and compared with perturbations from standard tent support. The measured perturbations in the “fishing pole,” cantilevered fill tube, and “tetra-cage” concepts compared favorably with (were smaller than) nominal tent perturbations and were recommended for further testing for feasibility in layered DT implosions. The “polar tents” were tested in layered DT implosions with a relatively-stable “high-foot” drive showing an improvement in neutron yield in one experiment compared to companion implosions with nominal tents. Furthermore, this article reviews and summarizes recent experiments on these alternate capsule support concepts. In addition, the concept of magnetic levitation is also discussed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Fusion Energy Output Greater than the Kinetic Energy of an Imploding Shell at the National Ignition Facility

A series of cryogenic, layered deuterium-tritium (DT) implosions have produced, for the first time, fusion energy output twice the peak kinetic energy of the imploding shell. These experiments at the National Ignition Facility utilized high density carbon ablators with a three-shock laser pulse (1.5 MJ in 7.5 ns) to irradiate low gas-filled ( 0.3 mg / cc of helium) bare depleted uranium hohlraums, resulting in a peak hohlraum radiative temperature ~ 290 eV . The imploding shell, composed of the nonablated high density carbon and the DT cryogenic layer, is, thus, driven to velocity on the order of 380 km / s resulting in a peak kinetic energy of ~ 21 kJ , which once stagnated produced a total DT neutron yield of 1.9 × 10 16 (shot N170827) corresponding to an output fusion energy of 54 kJ. Time dependent low mode asymmetries that limited further progress of implosions have now been controlled, leading to an increased compression of the hot spot. Finally, it resulted in hot spot areal density ( ρr ~ 0.3 g / cm 2 ) and stagnation pressure ( ~ 360 Gbar ) never before achieved in a laboratory experiment.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Mitigation of X-ray shadow seeding of hydrodynamic instabilities on inertial confinement fusion capsules using a reduced diameter fuel fill-tube

We report a reduced X-ray shadow imprint of hydrodynamic instabilities on the high-density carbon ablator surface of inertial confinement fusion (ICF) capsules using a reduced diameter fuel fill tube on the National Ignition Facility (NIF). The perturbation seed mass from hydrodynamic instabilities was reduced by approximately an order of magnitude by reducing both the diameter and wall thickness of the fill tube by ~2×, consistent with analytical estimates. Overall, this work demonstrates a successful mitigation strategy for engineered features for ICF implosions on the NIF.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Optimization of a high-yield, low-areal-density fusion product source at the National Ignition Facility with applications in nucleosynthesis experiments

Polar-direct-drive exploding pushers are used as a high-yield, low-areal-density fusion product source at the National Ignition Facility with applications including diagnostic calibration, nuclear security, backlighting, electron-ion equilibration, and nucleosynthesis-relevant experiments. In this paper, two different paths to improving the performance of this platform are explored: (i) optimizing the laser drive, and (ii) optimizing the target. While the present study is specifically geared towards nucleosynthesis experiments, the results are generally applicable. Example data from T 2 / 3 He-gas-filled implosions with trace deuterium are used to show that yield and ion temperature (Tion) from 1.6 mm-outer-diameter thin-glass-shell capsule implosions are improved at a set laser energy by switching from a ramped to a square laser pulse shape, and that increased laser energy further improves yield and Tion, although by factors lower than predicted by 1 D simulations. Using data from D2-3He-gas-filled implosions, yield at a set Tion is experimentally verified to increase with capsule size. Uniform D-3He-proton spectra from 3 mm-outer-diameter CH shell implosions demonstrate the utility of this platform for studying charged-particle-producing reactions relevant to stellar nucleosynthesis.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Visualizing deceleration-phase instabilities in inertial confinement fusion implosions using an “enhanced self-emission” technique at the National Ignition Facility

High-mode perturbations and low-mode asymmetries were measured in the deceleration phase of indirectly-driven, deuterium gas filled inertial confinement fusion (ICF) capsule implosions at convergence ratios of 10 to 15, using a new “enhanced emission” technique at the National Ignition Facility (NIF) [E. M. Campbell, R. Cauble, and B. A. Remington, AIP Conf. Proc. 429, 3 (1998)]. In these experiments, a high spatial resolution Kirkpatrick-Baez microscope was used to image the x-ray emission from the inner surface of a high-density-carbon (HDC) capsule’s shell. Use of a high atomic number dopant in the shell enabled time-resolved observations of shell perturbations penetrating into the hot spot. This allowed the effects of the perturbations and asymmetries on degrading neutron yield to be directly measured. In particular, mix induced radiation losses of ~400 J from the hot spot resulted in a neutron yield reduction of a factor of ~2. In a subsequent experiment with a significantly increased level of short-mode initial perturbations, shown through the enhanced imaging technique to be highly organized radially, the neutron yield dropped an additional factor of ~2.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Variable convergence liquid layer implosions on the National Ignition Facility

Liquid layer implosions using the “wetted foam” technique, where the liquid fuel is wicked into a supporting foam, have been recently conducted on the National Ignition Facility for the first time [Olson et al., Phys. Rev. Lett. 117, 245001 (2016)]. In this paper, we report on a series of wetted foam implosions where the convergence ratio was varied between 12 and 20. Reduced nuclear performance is observed as convergence ratio increases. 2-D radiation-hydrodynamics simulations accurately capture the performance at convergence ratios (CR) ~ 12, but we observe a significant discrepancy at CR ~ 20. Finally, this may be due to suppressed hot-spot formation or an anomalous energy loss mechanism.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Process Developments in the Fabrication of Depleted Uranium Hohlraums

Research at General Atomics and Lawrence Livermore National Laboratory has been focused on evaluating depleted uranium (DU) hohlraum fabrication over the past 10 years to improve the yield, thereby increasing the availability of DU hohlruams required to support the increased shot rate at the National Ignition Facility. The more straightforward gold (Au) hohlraum fabrication involves four basic steps: mandrel fabrication, electroplating, back machining and milling, and leaching. For Au, the overall fabrication yield of this process approaches 98%. Depleted uranium lined hohlraum fabrication, however, requires deposition of a multilayer of thin films after the mandrel fabrication step. These thin film deposition processes have historically proven difficult to execute on a complex cylindrical geometry of a hohlraum, resulting in unacceptable stress-driven delamination, with net yields ranging 20% to 35%. Recent hohlraum design and fabrication process changes, as well as material selections implemented between 2014 and 2016, have improved the fabrication yield to over 60%. Additionally, these changes are discussed here as well as plans for future improvements.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Hydro-instability growth of perturbation seeds from alternate capsule-support strategies in indirect-drive implosions on National Ignition Facility

Hydrodynamic instability growth of the capsule support membranes (or “tents”) and fill tubes has been studied in spherical, glow discharge polymer plastic capsule implosions at the National Ignition Facility (NIF). In NIF implosions, the capsules are supported by tents because the nominal 10-μm thick fill tubes are not strong enough to support capsules by themselves. After it was recognized that the tents had a significant impact of implosion stability, new support methods were investigated, including thicker, 30-μm diameter fill tubes and cantilevered fill tubes, as described in this article. A new “sub-scale” version of the existing x-ray radiography platform was developed for measuring growing capsule perturbations in the acceleration phase of implosions. It was calibrated using hydrodynamic growth measurements of pre-imposed capsule modulations with Legendre modes of 60, 90, 110, and 140 at convergence ratios up to ~2.4. Subsequent experiments with 3-D perturbations have studied instability growth of 10-μm and 30-μm thick fill tubes to compare them with 30-nm thick tent perturbations at convergence ratios up to ~3. In other experiments, the perturbations from cantilevered fill tubes were measured and compared to the tent perturbations. The cantilevered fill tubes were supported by 12-μm thick SiC rods, offset by 100 μm, 200 μm, and 300 μm from the capsule surfaces. Based on these experiments, 30-μm thick fill tubes and 300-μm offset cantilevered fill tubes were recommended for further tests using layered deuterium-tritium implosions. In conclusion, the effects of x-ray shadowing during the drive and oxygen-induced perturbations during target assembly produced additional seeds for instabilities and were also measured in these experiments.

42 ENGINEERING↗

Fabrication of Bromine-doped Glow Discharge Polymer Capsules

Bromine-doped capsules are needed to study charged particle production and transport via radiochemistry techniques in ignition experiments. The capsules require 2 ×10 16 bromine atoms in the inner-most layer. This proved to be challenging because bromine migrates to different layers during the standard GDP capsule production process. In addition, an unexpected Br-Si interaction resulted in substantial amount of bromine trapped in middle Si-doped layers and became co-doped. Lastly, combined metrology techniques, including edge absorption spectroscopy, contact radiography, X-ray fluorescence and energy dispersive X-ray spectroscopy (EDS) and scanning electron microscope, are used to resolve bromine distribution in the capsules.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

Mix and hydrodynamic instabilities on NIF

Several new platforms have been developed to experimentally measure hydrodynamic instabilities in all phases of indirect-drive, inertial confinement fusion implosions on National Ignition Facility. At the ablation front, instability growth of pre-imposed modulations was measured with a face-on, x-ray radiography platform in the linear regime using the Hydrodynamic Growth Radiography (HGR) platform. Modulation growth of "native roughness" modulations and engineering features (fill tubes and capsule support membranes) were measured in conditions relevant to layered DT implosions. A new experimental platform was developed to measure instability growth at the ablator-ice interface. Here in the deceleration phase of implosions, several experimental platforms were developed to measure both low-mode asymmetries and high-mode perturbations near peak compression with x-ray and nuclear techniques. In one innovative technique, the self-emission from the hot spot was enhanced with argon dopant to "self-backlight" the shell in-flight. To stabilize instability growth, new "adiabat-shaping" techniques were developed using the HGR platform and applied in layered DT implosions.

42 ENGINEERING↗

Quantitative Defect Analysis of Ablator Capsule Surfaces Using a Leica Confocal Microscope and a High-Density Atomic Force Microscope

High-density carbon (HDC) is being evaluated as an alternative to the current National Ignition Facility (NIF) point-design ablator material (glow discharge plasma, or GDP, plastic) due to its high density and optimal opacity, which leads to a higher implosion velocity. Chemical-vapor-deposition-coated HDC capsules have a near perfect surface figure but a microscopically rough surface. After polishing, the surface becomes smooth at nanometer scales but has numerous micron-sized surface pits, whose volumes, morphology, and distribution must be quantified to guide NIF target selection. Traditional metrology tools for GDP surface defects, such as the atomic force microscope (AFM) based Spheremapper and a phase-shifting differential interferometer, lack the resolution to characterize these localized features. In this paper, we describe how this metrology challenge is met by developing automated surface metrology solutions based on a high-density (HD) AFM and a Leica confocal microscope. Furthermore, these tools are complementary in nature. HD-AFM has a 0.1-μm spatial resolution and determines the overall shape distortion and pit statistics by tracing great circles on a capsule with high throughput.

36 MATERIALS SCIENCE↗

The role of hot spot mix in the low-foot and high-foot implosions on the NIF

Hydrodynamic mix of the ablator into the DT fuel layer and hot spot can be a critical performance limitation in inertial confinement fusion implosions. This mix results in increased radiation loss, cooling of the hot spot, and reduced neutron yield. To quantify the level of mix, we have developed a simple model that infers the level of contamination using the ratio of the measured x-ray emission to the neutron yield. The principal source for the performance limitation of the “low-foot” class of implosions appears to have been mix. As a result, lower convergence “high-foot” implosions are found to be less susceptible to mix, allowing velocities of >380 km/s to be achieved.

42 ENGINEERING↗

Performance of beryllium targets with full-scale capsules in low-fill 6.72-mm hohlraums on the National Ignition Facility

When used with 1.06-mm beryllium (Be) capsules on the National Ignition Facility, gold hohlraums with the inner diameter of 5.75 mm and helium gas fill density of 1.6 mg/cm 3 exhibit significant drive degradation due to laser energy backscatter (of order 14%–17%) and “missing” X-ray drive energy (about 32% during the main pulse). Also, hard to simulate cross-beam energy transfer (CBET) must be used to control the implosion symmetry. Larger, 6.72-mm hohlraums with fill densities ≤0.6 mg/cm 3 generally offer improved drive efficiency, reduced hot-electron preheat, and better control of the implosion symmetry without CBET. Recently, we carried out an exploratory campaign to evaluate performance of 1.06-mm Be capsules in such hohlraums and determine optimal hohlraum parameters. Specifically, we performed in this paper a hohlraum fill-density scan with a three-shock, 9.5-ns laser pulse and found that an appropriate axial laser repointing and azimuthal outer-quad splitting resulted in significantly improved hohlraum energetics at fill densities ≤0.3 mg/cm 3 (with backscattered and “missing” energies being of about 5% and 23% of the total laser energy, respectively). The capsule shape at stagnation was slightly oblate and improved with lowering the fill density. We also performed an implosion with a lower-picket, 12.6-ns pulse at the hohlraum fill density of 0.15 mg/cm 3 to observe comparable hohlraum energetics (about 3% of backscattered and 27% of “missing” energy) but an even more oblate implosion shape. Finally, achieving symmetric implosions of 1.06-mm Be capsules in low-fill, 6.72-mm gold hohlraums with reasonably low-adiabat pulses may not be feasible. However, symmetric implosions have recently been successfully demonstrated in such hohlraums with 0.8-mm Be capsules.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Short pulse, high resolution, backlighters for point projection high-energy radiography at the National Ignition Facility

High-resolution, high-energy X-ray backlighters are very active area of research for radiography experiments at the National Ignition Facility (NIF) [Miller et al., Nucl. Fusion 44, S228 (2004)], in particular those aiming at obtaining Compton-scattering produced radiographs from the cold, dense fuel surrounding the hot spot. We report on experiments to generate and characterize point-projection-geometry backlighters using short pulses from the advanced radiographic capability (ARC) [Crane et al., J. Phys. 244, 032003 (2010); Di Nicola et al., Proc. SPIE 2015, 93450I-12], at the NIF, focused on Au micro-wires. We show the first hard X-ray radiographs, at photon energies exceeding 60 keV, of static objects obtained with 30 ps-long ARC laser pulses, and the measurements of strength of the X-ray emission, the pulse duration and the source size of the Au micro-wire backlighters. For the latter, a novel technique has been developed and successfully applied.

42 ENGINEERING↗

Hydrodynamic instability growth of three-dimensional modulations in radiation-driven implosions with “low-foot” and “high-foot” drives at the National Ignition Facility

Hydrodynamic instability growth has been studied using three-dimensional (3-D) broadband modulations by comparing “high-foot” and “low-foot” spherical plastic (CH) capsule implosions at the National Ignition Facility (NIF). The initial perturbations included capsule outer-surface roughness and capsule-mounting membranes (“tents”) that were similar to those used in a majority of implosions on NIF. The tents with thicknesses of 31-nm, 46-nm, and 109-nm were used in the experiments. The outer-surface roughness in the “low-foot” experiment was similar to the standard specification, while it was increased by ~4 times in the “high-foot” experiment to compensate for the reduced growth. The ablation-front instability growth was measured using a Hydrodynamic Growth Radiography platform at a convergence ratio of 3. The dominant capsule perturbations, generated by the tent mountings, had measured perturbation amplitudes comparable to the capsule thickness with the “low-foot” drive. These tent perturbations were reduced by ~3 to 10 times in implosions with the “high-foot” drive. Unexpectedly, the measured perturbations with initially thinner tents were either larger or similar to the measured perturbations with thicker tents for both “high-foot” and “low-foot” drives. While the measured instability growth of 3-D broadband perturbations was also significantly reduced by ~5 to 10 times with the “high-foot” drive, compared to the “low-foot” drive, the growth mitigation was stronger than expected based on previous “growth-factor” results measured with two-dimensional modulations. Lastly, one of the hypotheses to explain the results is based on the 3-D modulations of the oxygen content in the bulk of the capsule having a stronger effect on the overall growth of capsule perturbations than the outer-surface capsule roughness.

42 ENGINEERING↗