Engineering topics
Ninnemann, Erik
Publications and source records attributed to Ninnemann, Erik.
Shock Tube and Flame Speed Measurements of 2,4,4-Trimethyl-1-Pentene: A Co-Optima Biofuel
Abstract The combustion of 2,4,4-trimethyl-1-pentene (diisobutylene, C8H16), which is a biofuel and a component of surrogate fuels, is examined in this work. Carbon monoxide time–histories and ignition delay times are collected behind reflected shock waves utilizing a shock tube and mid-infrared laser absorption spectroscopy. Measurements were obtained near 10 atm pressure during stoichiometric oxidation of 0.15%C8H16/O2/Ar. Simulated results from chemical kinetic models are provided, and sensitivity analyses are used to discuss differences between models for both ignition delay times and carbon monoxide formation. In addition, laminar burning speeds are obtained at 1 atm, 428 K, and equivalence ratios, phi, between 0.91 and 1.52 inside a spherical chamber facility. Measured burning speeds are found to be less than that of ethanol over the equivalence ratio span. Burning speed measurements are compared to predictions of chemical kinetic mechanisms and are in agreement for the richest conditions; however, at lean conditions, the model predicts a far slower-burning speed. The maximum burning speed occurs at an equivalence ratio of 1.08 with a magnitude of 0.70 m/s. The current work provides the crucial experimental data needed for assessing the feasibility of this biofuel and for the development of future combustion chemical kinetics models.
Oxidation and pyrolysis of methyl propyl ether
The ignition, oxidation, and pyrolysis chemistry of methyl propyl ether (MPE) was probed experimentally at several different conditions, and a comprehensive chemical kinetic model was constructed to help understand the observations, with many of the key parameters computed using quantum chemistry and transition state theory. Experiments were carried out in a shock tube measuring time variation of CO concentrations, in a flow tube measuring product concentrations, and in a rapid compression machine (RCM) measuring ignition delay times. The detailed reaction mechanism was constructed using the Reaction Mechanism Generator software. Sensitivity and flux analyses were used to identify key rate and thermochemical parameters, which were then computed using quantum chemistry to improve the mechanism. Validation of the final model against the 1-20 bar 600-1500 K experimental data is presented with a discussion of the kinetics. The model is in excellent agreement with most of the shock tube and RCM data. Strong non-monotonic variation in conversion and product distribution is observed in the flow-tube experiments as the temperature is increased, and unusually strong pressure dependence and significant heat release during the compression stroke is observed in the RCM experiments. These observations are largely explained by a close competition between radical decomposition and addition to O2 at different sites in MPE; this causes small shifts in conditions to lead to big shifts in the dominant reaction pathways. The validated mechanism was used to study the chemistry occurring during ignition in a diesel engine, simulated using Ignition Quality Test (IQT) conditions. At the IQT conditions, where the MPE concentration is higher, bimolecular reactions of peroxy radicals are much more important than in the RCM.
Ignition delay time and speciation of dibutyl ether at high pressures
Dibutyl ether (DBE) is a promising biofuel due to its high cetane number (~ 100) and high volumetric energy density (31.6 MJ/L). It could either be used directly in compression ignition engines or blended with other conventional or renewable fuels. Oxidation and pyrolysis kinetics of DBE are not well known, particularly at high pressures. In this work, we have experimentally investigated the chemical kinetics of DBE in three domains: (a) ignition delay time measurements in a rapid compression machine over T = 550–650 K, P = 10, 20, 40 bar, φ = 0.5, 1; (b) ignition delay time measurements in a shock tube over T = 900–1300 K, P = 20, 40 bar, φ = 0.5, 1; (c) laser-based carbon monoxide speciation measurements in a shock tube during DBE pyrolysis and oxidation over T = 1100–1400 K, P = 20 bar. Pressure time-histories measured in RCM experiments exhibited unique 3-stage and 4-stage ignition behavior predominantly at fuel-lean conditions. Experimental data were compared with the predictions of two recent chemical kinetic models of DBE. Sensitivity analyses were carried out to identify key reactions which may have caused the discrepancy between experiments and simulations. We found that the rate of decomposition of DBE may need to be revisited to improve the oxidative and pyrolytic predictions of DBE kinetic model.
Reflected shock-initiated ignition probed via simultaneous lateral and endwall high-speed imaging with a transparent, cylindrical test-section
A TRAnsparent cylindrical (TRAC) shock tube test section has been developed to explore the ignition structure behind reflected shockwaves via simultaneous lateral and endwall high-speed imaging using three fuel/oxidizer mixtures: 0.1% n-C 7 H 16 /1.10% O 2 /4.14% N 2 /94.66% Ar, 0.1% iC 8 H 18 /1.25% O 2 /4.69% N 2 /93.96% Ar, and 5% CH 4 /10% O 2 /85% CO 2 . During mild ignition, the first exothermic centers were located outside of the observable test section. It is shown that with increasing temperature the far-wall ignition events move closer to the endwall, until a strong ignition is achieved. The temperature gradients that promote mild ignition were quantified and were found to have a slight dependence on fuel with the RMS temperature gradients being 0.80% for n-heptane and 1.07% for isooctane. The impact of temperature gradients on metrics used to improve kinetic models, such as species time histories, is noteworthy. From this temperature gradient, an experimental correlation is provided to estimate the transition temperature from mild to strong ignition for a mixture. The effect of diagnostic location in non-homogeneous reactions is quantified in reference to ignition delay. In conclusion, the unique and insightful perspective on the ignition process under heavy shock bifurcation is also discussed.
Influence of the double bond position in combustion chemistry of methyl butene isomers: A shock tube and laser absorption study
Shock tube experiments have been carried out on 2–methyl–1–butene (2M1B), 2–methyl–2–butene (2M2B), and 3–methyl–1–butene (3M1B)—the three isomers of methyl butene compound. Here, carbon monoxide (CO) time–histories and ignition delay times are obtained behind reflected shockwaves over the temperature range of 1350–1630 K and pressures of 8.3–10.5 atm with stoichiometric mixtures of 0.075% fuel in O 2 /Ar. Comparative ignition study reveals that 3M1B ignites significantly faster than the other two isomers, while 2M1B dissociates earlier but ignites later than 2M2B. Possible mechanisms for this behavior are discussed with ignition delay time sensitivity and reaction path analysis. In addition, time–resolved CO measurements are compared with three different reaction mechanisms from the literature. Sensitivity analyses have been carried out to identify important reactions that need attention to accurately predict the chemistry of these isomers. Further investigation into the rates of unimolecular fuel decomposition reactions and C 3 H 3 + O 2 = CH 2 CO + HCO reaction are suggested based on the current investigation.
Probing the Effects of NO x and SO x Impurities on Oxy-Fuel Combustion in Supercritical CO 2 : Shock Tube Experiments and Chemical Kinetic Modeling
The direct-fired supercritical carbon dioxide cycles are one of the most promising power generation methods in terms of their efficiency and environmental friendliness. Two important challenges in implementing these cycles are the high pressure (300 bar) and high CO 2 dilution (>80%) in the combustor. The design and development of supercritical oxy-combustors for natural gas require accurate reaction kinetic models to predict the combustion outcomes. The presence of a small amount of impurities in natural gas and other feed streams to oxy-combustors makes these predictions even more complex. During oxy-combustion, trace amounts of nitrogen present in the oxidizer is converted to NO x and gets into the combustion chamber along with the recirculated CO 2 . Similarly, natural gas can contain a trace amount of ammonia and sulfurous impurities that get converted to NO x and SO x and get back into the combustion chamber with recirculated CO 2 . In this work, a reaction model is developed for predicting the effect of impurities such as NO x and SO x on supercritical methane combustion. The base mechanism used in this work is GRI Mech 3.0. H 2 S combustion chemistry is obtained from Bongartz et al. while NOx chemistry is from Konnov. The reaction model is then optimized for a pressure range of 30–300 bar using high-pressure shock tube data from the literature. It is then validated with data obtained from the literature for methane combustion, H 2 S oxidation, and NO x effects on ignition delay. The effect of impurities on CH 4 combustion up to 16 atm is validated using NO x -doped methane studies obtained from the literature. In order to validate the model for high-pressure conditions, experiments are conducted at the UCF shock tube facility using natural gas identical mixtures with N 2 O as an impurity at ~100 bar. Current results show that there is a significant change in ignition delay with the presence of impurities. A comparison is made with experimental data using the developed model and predictions are found to be in good agreement. The model developed was used to study the effect of impurities on CO formation from sCO 2 combustors. It was found that NO x helps in reducing CO formation while the presence of H 2 S results in the formation of more CO. The reaction mechanism developed herein can also be used as a base mechanism to develop reduced mechanisms for use in CFD simulations.
Effects of High Fuel Loading and CO2 Dilution on Oxy-Methane Ignition Inside a Shock Tube at High Pressure
Abstract Ignition delay times were measured for methane/O2 mixtures in a high dilution environment of either CO2 or N2 using a shock tube facility. Experiments were performed between 1044 K and 1356 K at pressures near 16 ± 2 atm. Test mixtures had an equivalence ratio of 1.0 with 16.67% CH4, 33.33% O2, and 50% diluent. Ignition delay times were measured using OH* emission and pressure time-histories. Data were compared to the predictions of two literature kinetic mechanisms (ARAMCO MECH 2.0 and GRI Mech 3.0). Most experiments showed inhomogeneous (mild) ignition which was deduced from five time-of-arrival pressure transducers placed along the driven section of the shock tube. Further analysis included determination of blast wave velocities and locations away from the end wall of initial detonations. Blast velocities were 60–80% of CJ-Detonation calculations. A narrow high temperature region within the range was identified as showing homogenous (strong) ignition which showed generally good agreement with model predictions. Model comparisons with mild ignition cases should not be used to further refine kinetic mechanisms, though at these conditions, insight was gained into various ignition behavior. To the best of our knowledge, we present first shock tube data during ignition of high fuel loading CH4/O2 mixtures diluted with CO2 and N2.
Revealing the critical role of radical-involved pathways in high temperature cyclopentanone pyrolysis
Cyclopentanone (CPO) is a promising biofuel for spark-ignition engines due to its ring strain and high auto-ignition resistance. Understanding CPO decomposition is crucial for building a high-temperature combustion model. Here we present a comprehensive kinetic model for high-temperature pyrolysis of CPO with verified results from high-pressure shock tube (HPST) measurements. The time- histories of carbon monoxide (CO), ethylene (C 2 H 4 ), and CPO absorbances over the temperature range of 1156-1416 K and pressure range of 8.53-10.06 atm were measured during current experiments. A corresponding detailed kinetic model was generated using the Reaction Mechanism Generator (RMG) with dominant unimolecular/radical-involved decomposition pathways from either previous studies or quantum calculations within the current work. The obtained model containing 821 species and 79,859 reactions exhibited a good agreement with the experimental results. In this study, the absorbance ratio between C 2 H 4 and CO was used as an important factor to validate models and to prove that radical-involved bimolecular pathways were as significant as unimolecular decomposition of CPO. The rate of production (ROP) analysis showed H radicals play a major role in the decomposition, and the whole decomposition process could be divided into three stages based on the H radical concentration. Finally, the insights from present work can be used to generate a better CPO combustion model and help evaluate CPO as an advanced biofuel.
Measuring the effectiveness of high-performance Co-Optima biofuels on suppressing soot formation at high temperature
Soot emissions in combustion are unwanted consequences of burning hydrocarbon fuels. The presence of soot during and following combustion processes is an indication of incomplete combustion and has several negative consequences including the emission of harmful particulates and increased operational costs. Efforts have been made to reduce soot production in combustion engines through utilizing oxygenated biofuels in lieu of traditional nonoxygenated feedstocks. The ongoing Co-Optimization of Fuels and Engines (Co-Optima) initiative from the US Department of Energy (DOE) is focused on accelerating the introduction of affordable, scalable, and sustainable biofuels and high-efficiency, low-emission vehicle engines. The Co-Optima program has identified a handful of biofuel compounds from a list of thousands of potential candidates. In this study, a shock tube was used to evaluate the performance of soot reduction of five high-performance biofuels downselected by the Co-Optima program. Current experiments were performed at test conditions between 1,700 and 2,100 K and 4 and 4.7 atm using shock tube and ultrafast, time-resolve laser absorption diagnostic techniques. The combination of shock heating and nonintrusive laser detection provides a state-of-the-art test platform for high-temperature soot formation under engine conditions. Soot reduction was found in ethanol, cyclopentanone, and methyl acetate; conversely, an α-diisobutylene and methyl furan produced more soot compared to the baseline over longer test times. For each biofuel, several reaction pathways that lead towards soot production were identified. The data collected in these experiments are valuable information for the future of renewable biofuel development and their applicability in engines.