Engineering topics
Nino, Juan C.
Publications and source records attributed to Nino, Juan C..
Solar Thermochemical Redox Cycling Using Ga- and Al-Doped LSM Perovskites for Renewable Hydrogen Production
Solar thermochemical hydrogen production using redox-active metal oxides is a promising pathway for the production of green hydrogen and synthetic fuel precursors. Herein, the perovskite material (La 0.6 Sr 0.4 ) 0.95 Mn 0.8 Ga 0.2 O 3–δ (LSMG6482) is identified as a promising metal oxide for thermochemical water splitting. LSMG6482, along with more-established water splitters ceria and (La 0.6 Sr 0.4 ) 0.95 Mn x Al 1–x O 3–δ (LSMA) perovskites, is experimentally characterized via thermogravimetric (TGA) analysis and high-temperature water splitting in a reactor simulating solar concentrating conditions. TGA analysis demonstrated that LSMG6482 has high and stable oxygen exchange capacity under controlled pO 2 redox cycling, demonstrated by large changes in oxygen nonstoichiometry (δ) relative to ceria. Water splitting experiments using laser heating (T red = 1400 °C, T ox = 1200 °C) resulted in H 2 yields of 165.1 μmol g –1 for the candidate LSMG6482 composition, exceeding that of all benchmark materials tested. Under high conversion oxidation conditions, where H 2 is cointroduced with H 2 O (150 ≤ nH 2 O/nH 2 ≤ 500), H 2 yields were greatest for LSMG6482 and LSMA6482, up to four times that of ceria at the highest nH 2 O/nH 2 conditions. Crystallographic analysis showed that over the course of experimentation, there is some secondary phase growth for all perovskite compositions, except for LSMA6482, but there was no observable degradation in H 2 yields.
LaMnO 3 Dopants for Efficient Thermochemical Water Splitting Identified by Density Functional Theory Calculations
While ceria is the standard material for two-step water splitting, perovskites are emerging as viable alternatives. In this work, based on the orthorhombic LaMnO 3 supercell, we substitute Li Na K Rb Mg Ca Sr Ba on the A-sites (La sites) and Al Ga In Mg Zn on the B-sites (Mn sites) at a concentration of 37.5%. The range of temperature and oxygen partial pressure at which each composition is stable is predicted. For compositions that are stable in relevant temperature and pressure ranges, the oxygen vacancy formation energies are determined for all of the oxygen vacancy site positions available in the computational supercell. Mg, Ca, Sr, and Ba A-site-substituted LaMnO 3 and Al and In B-site-substituted LaMnO 3 meet these two criteria for candidates in solar-thermal water splitting applications. Finally, oxygen vacancy formation energy can also be controlled by adjusting the doping strategy.
Assessment of Bulk Oxygen Capacity and Transient Redox Behavior of Foamed Lanthanum Strontium Manganese Perovskites
Synthesis of solar thermochemical hydrogen (STCH) production redox materials with engineered structures, for example, replica foams, can enable efficient heat and mass transport and are critical for scaled-up systems. Prior work has motivated the use of lanthanum strontium manganese (LSM)-type perovskites as foamed STCH materials, but the effect of their morphology on bulk and kinetic behavior has not been reported. In this work, replica and direct foamed samples of La 0.65 Sr 0.35 MnO 3-δ (LSM35) were fabricated and compared to synthesized powders and dense monoliths, and similarly synthesized CeO 2-δ (ceria) foams, regarding their specific reaction rates and bulk oxygen capacity/H 2 yields. Changes in oxygen capacity (Δδ) and reaction rates were measured between 1200 °C and 1400 °C by using fixed ratios of steam and hydrogen during both reduction and oxidation steps, allowing for analysis under practical high conversion conditions. Results suggest bulk behavior and reaction rates of the foamed LSM materials are comparable to their powder analogues. Differences in reaction rates were observed only when replica foamed samples were subjected to rapid laser heating (emulating conditions expected in solar furnaces), which is expected but has not been demonstrated at such a small scale. Here, foamed samples were further subjected to 50 redox cycles at 1400 °C to evaluate their stability. Results show no statistically significant decrease in hydrogen production for any of the foamed samples, but the direct foamed samples became brittle with time. Together, these results demonstrate the viability of replica foamed LSM perovskites for integration in scaled-up STCH systems.
Properties of iron-functionalized organoclays. Consequences for pertechnetate sequestration
Not Available
Complex Oxide Nanoparticle Synthesis: Where to Begin to Do It Right?
Synthesis of advanced ceramics requires a high degree of control over the particle size and stoichiometry of the material. When choosing a synthesis method for complex oxides it is important to begin with the correct precursors and solvents to achieve high purity nanoparticles. Here, we detail the selection process for precursors and solvents for liquid-phase precipitation synthesis. Data for metal nitrate, chloride, acetate, and oxalate precursors has been compiled to assist future synthesis. The role of hydration within the precursors is discussed as it affects the final stoichiometry of the material. Melting temperatures are also compiled for these compounds to assist in material selection. The solubility of the precursors in different solvents is examined to determine the correct solvent during synthesis. As an example, using the methodology presented here, two different materials are synthesized based on commonly available precursors. A catalyst based on a quaternary perovskite and an advanced ionic conductor based on a high entropy fluorite oxide are synthesized using precipitation methods and their characterization is detailed.
Effect of Remnant Carbon and Etching of Particles on Pyrolysis Bonded Silicon Carbide (PBSC)
Silicon carbide (SiC) formed through pyrolysis of preceramic polymers loaded with SiC particles has gained significant attention for applications such as coatings, composite matrix modifications, and most importantly additive manufacturing. This work presents combined synchrotron XRD, Raman spectroscopy, scanning electron microscopy, nano-indentation, and Vickers indentation of pyrolysis bonded SiC to shed light on the changes of composition and mechanical properties of these materials. Characterization was performed on samples that were heat treated ranging from the synthesis 850 °C up to 1500 °C. Pre-treatments of the powders prior to pellet synthesis, such as heat treatment and etching using a hydrofluoric acid (HF), were investigated. It is shown that the degradation of mechanical properties when exposed to higher temperatures is due to the burnout of amorphous carbon clusters remnant of the pyrolysis process of the preceramic polymer. Furthermore, prior HF etching and removal of the native oxide layer of the powders showed improved density and hardness values in the final pellets. The average Vickers hardness of the control samples were 4.59 GPa and later 3.74 GPa when exposed to 1500 °C, while the samples synthesized using powders that were etched with HF had an average hardness value of 9.37 GPa and later 6.86 GPa when exposed to 1500 °C.
Reticulated porous lanthanum strontium manganite structures for solar thermochemical hydrogen production
Porous ceramic foams are utilized in various fields and applications due to their advantageous properties such as high porosity, high specific surface area, and controlled permeability. Non-stoichiometric oxide foams are of particular interest for the solar thermochemical production of hydrogen in directly irradiated solar receivers due to their enhanced heat transfer capabilities and structural integrity. Here we report the fabrication of lanthanum strontium manganite replica foams and their solar thermochemical water splitting performance. Highly porous (>80%) foams were produced with controlled structure and tested in a high temperature water splitting furnace to demonstrate stability and overall performance. The temperature profile of the burnout and sintering of the foam structure were altered based on simultaneous differential scanning calorimetry and thermal gravimetry analysis. Two-step sintering was used both to retain micron-sized pores (D50 = 0.4 μm) on the foam's struts and to limit grain growth to a grain size of ~1 μm. The structural characteristics were confirmed by porosimetry and scanning electron microscopy. The foams were repeatedly cycled, producing approximately 200 μmol/g of H 2 per cycle. Water splitting performance was tested for 50 cycles and approximately 35 h at 1400 °C. No statistical difference in the effective hydrogen production per cycle was observed, which is promising for long-term redox cycle stability.
Microstructure evolution of gadolinium doped cerium oxide under large thermal gradients
In this report the effects of large thermal gradient annealing on the microstructure of 10 mol% gadolinium doped ceria (GDC) were investigated. GDC powder was prepared by solvent deficient method and sintered at 1650 °C for 10 h to achieve dense ceramics with ~8 μm grain size. The densified GDC samples were subsequently annealed using a 60 W infrared laser at over 2100 °C for 1 h under a thermal gradient equivalent to ~0.3–0.5 °C/μm. The post-annealed samples at 2150 °C for 1 h exhibit grains with average length and width of 37 and 28 μm, respectively. Electron backscattered diffraction (EBSD) analysis revealed that the post-annealed sample at 2150 °C consists of grains oriented close to five principal directions (<4 3 10>, <0 0 1> and <13 1 14> on [0 0 1], and <7 6 20> and <7 2 7> on [0 1 0]) within a tolerance angle of ±10°, whereas the grains of the pre-annealed sample are randomly oriented. Gadolinium diffuses 20–30 μm away from the irradiated surface, with the measured composition of regions deeper than 30 μm, Ce 0.86 Gd 0.14 O 1.93 , is close to that of the pre-annealed sample, Ce 0.87 Gd 0.13 O 1.94 . Enhancement of total conductivity of the post-annealed GDC (1.1 × 10 -3 S cm -1 at 500 °C, and 2.1 × 10 -2 S cm -1 at 700 °C) is observed when compared to the pre-annealed GDC (3.1 × 10 -5 S cm -1 at 500 °C, and 1.7 × 10 -3 S cm -1 at 700 °C), and points to the decrease in the grain boundary (GB) resistivity. This could be attributed to both the change in GB area and grain alignment.
22 K superconductivity in Ba Fe 2 As 2 exposed to F 2
Several previous reports on undoped AEFe 2 As 2 (AE = alkaline earth metal) point to drops in resistivity indicative of possible superconductivity and some degree of Meissner effect in the magnetic susceptibility. Also, based on both resistivity and magnetic susceptibility measurements, controlled exposure to water vapor has been shown to induce superconductivity in AEFe 2 As 2 . In our study, BaFe 2 As 2 single crystals grown using the self-flux method showed a full resistive drop around 22 K and magnetic shielding, when exposed to fluorine gas postgrowth. Our measurements indicate electron (donor) doping via atomic substitution of F for As is concurrent with the observed superconductivity, which sheds light on the likely effect of exposure to water vapor in previous work. Like doping experiments (such as substitution of Co for Fe, P for As, or K for Ba) in AEFe 2 As 2 to date, the present work is consistent with suppression of the spin density wave transition coincident with the appearance of T c . In addition to answering the puzzle of superconductivity in undoped or water vapor exposed AEF 2 As 2 , our results also represent a fast (20 min exposure to 5% F in He) and reliable method suitable for inducing superconductivity in thin films of AEFe 2 As 2 . As a result, some supportive work on BaFe 2 As 2 exposed to Cl 2 is also presented.