Search NASA⌕ Search

Engineering topics

Norman, Andrew

Publications and source records attributed to Norman, Andrew.

At least 19 records

Optoelectronic and structural characterization of trapezoidal defects in 4H-SiC epilayers and the effect on MOSFET reliability

To this day, trapezoidal defects are found in clusters and high counts in wafers representing the industry standard in terms of material quality being produced. This study sheds light on the nature, origin, behavior, and impact of this defect on device yield and reliability. Trapezoidal defects in 4H-SiC epitaxial layers were investigated by photoluminescence (PL) imaging, scanning electron microscopy (SEM), cathodoluminescence spectrum imaging (CLSI), SEM electron beam induced current (EBIC) imaging, and by transmission electron microscopy (TEM) observation. The bar-shaped stacking faults were identified by the PL and CL measurements with a peak emission wavelength of 420 and 450 nm. An optoelectronic behavioral study based on the recombination enhanced dislocation glide mechanism revealed how expanding dislocations and stacking faults interact with each other. Combining the luminescence and microscopy results, the nature of the stacking faults was identified as being a combination of Shockley-type and Frank-type stacking faults. The TEM analysis showed that these defects originate from the substrate and the stacking sequences of some of the faults were determined as (…2, 4, 2…) and (…2, 3, 2…) in the Zhdanov's notation by high-resolution TEM. The origin of this defect is speculated based on our results and previous reports. The EBIC imaging showed that the high density of SFs in these towers is a strong site of carrier recombination, which presumably has an impact on the transfer characteristics of SiC devices. Furthermore, these defects have shown to impact metal oxide semiconductor field effect transistors electrical performance via an increase in the on-state resistance depending on the coverage percentage of the tower of defects in the active area of the device.

4H-SiC↗

Solar Energy from a Big Picture Perspective to Nanoscale Insights via TOF-SIMS

The world is undergoing a rapid transformation in the ways that we generate and store energy. This has been driven not only by concerns about the climate but by simple economic factors due to the dramatic cost decreases in wind in solar power. In most places of the world where one would now want to build a new power plant, the cheapest option is to use wind of solar for power generation. Abundant clean energy when the sun shines most is driving new research for daily and seasonal energy storage in many different technologies. Here, we will briefly these discuss energy trends as a whole, before diving into our recent contributions to the field using time-of-flight secondary-ion mass spectrometry (TOF-SIMS) to improve the performance and reliability of solar cells.

14 SOLAR ENERGY↗

HEPnOS: a Specialized Data Service for High Energy Physics Analysis

In this paper, we present HEPnOS, a distributed data service for managing data produced by high-energy physics (HEP) experiments. Using HEPnOS, HEP applications can use HPC resources more effciently than traditional fle-based applications. The fle-based model leads to a rigid, chunk-based allocation of computational resources and limits the number of cores that can be used concurrently by an HEP application. The fundamental problem is that organizing domain-specifc data into fles inadvertently introduces a single, artifcial, confated tuning parameter that puts key optimization goals into confict: larger fle sizes reduce metadata overhead and thus improve I/O effciency, but smaller fle sizes provide more opportunity for workfow parallelism and load balancing. In this work, we introduce a domain-specifc data service that decouples that constraint so that data can be accessed and processed in its natural granularity while still maintaining I/O effciency. By removing the constraints introduced by fle handling we are able to obtain better scaling and make effcient use of more cores for processing a fxed-sized data sample. We demonstrate the improved scalability by using an application developed in the fle-based paradigm and comparing it to a version modifed to use HEPnOS.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Multi-modal characterization methods of solid-electrolyte interphase in silicon-graphite composite electrodes

Composite silicon-graphite (Si-Gr) anodes can improve battery energy density, due to Si's high gravimetric capacity, while mitigating mechanical degradation of the anode and solid-electrolyte interphase (SEI) caused by Si volumetric expansion. Optimizing these anodes is challenging, in part due to difficulty characterizing the SEI structure and composition. In this work, we present multi-modal characterization of the SEI on composite Si-Gr anodes to relate SEI chemical composition and structure to functional properties. Discrepancies in elemental concentrations from X-ray photoelectron spectroscopy, Auger electron spectroscopy, and energy-dispersive X-ray spectroscopy (EDS) are attributed to varying information depth and lateral resolution of the individual probes. However, by combining quantitative composition information with spatially resolved element mapping from scanning transmission electron microscopy, EDS, and electron energy loss spectroscopy, a holistic picture of the SEI emerges. We observe the bilayer SEI structure and a direct correlation between elemental Li and F, suggesting that most Li in the SEI exists as lithium fluoride (LiF). Further, LiF concentration is directly proportional to the maximum SEI resistivity, as determined by scanning spreading resistance microscopy. Lastly, there is an inverse relationship between lithium carbonate and LiF concentration in the SEI, providing insight into the detailed chemistry of SEI formation and evolution.

25 ENERGY STORAGE↗

Multiscale Characterization of Photovoltaic Modules—Case Studies of Contact and Interconnect Degradation

The current popularity of photovoltaic (PV) systems is due in large part to their exceptional reliability and significantly lower cost than other energy sources. Studying cell and module degradation is key to promote further development in the state of the art. Fielded or accelerated aged modules exhibit different failure modes, of which metallization degradation (contacts and interconnections) is prevalent. In this work, we discuss how multiscale characterization methods can be applied to a variety of module technologies that have been field exposed and have undergone accelerated age testing. These methods include performing characterization on the module level, cell level, and finally the materials level. The observed performance losses from the module- and cell-level characterization can be correlated with materials properties to find out the root cause of degradation. We recommend an initial nondestructive characterization suite, including module- and cell-level current-voltage ( I--V ), Suns-V OC , photoluminescence and electroluminescence imaging, quantum efficiency, ultraviolet fluorescence imaging, and thermal infrared imaging. Samples are then extracted from particularly degraded regions of the module and prepared for materials characterization techniques, such as top-down and cross-sectional scanning electron microscopy, energy-dispersive X-ray spectroscopy, X-ray photoelectron spectroscopy, secondary ion mass spectrometry, Raman spectroscopy, and transmission electron microscopy, allowing a deeper look into the mechanism behind the metallization degradation. This article serves as an instructional review to introduce the different multiscale characterization methods and how they can be effectively applied to perform PV degradation studies. Furthermore, we also share some of our examples and discuss the strengths, limitations, and best practices for each of the characterization techniques.

14 SOLAR ENERGY↗

Low-latency NuMI Trigger for the CHIPS-5 Neutrino Detector

The CHIPS R&D project aims to develop affordable water Cherenkov detectors for large-scale underwater installations. In 2019, a 5kt prototype detector CHIPS-5 was deployed in northern Minnesota to study neutrinos generated by the nearby NuMI beam. This contribution presents a dedicated low-latency time distribution system for CHIPS-5 that delivers timing signals from the Fermilab accelerator to the detector with sub-nanosecond precision. Exploiting existing NOvA infrastructure, the time distribution system achieves this only with open-source software and conventional network elements. In a time-of-flight study, the presented system has reliably offered a time budget of $610 \pm 330\text{ ms}$ for on-site triggering. This permits advanced analysis in real-time as well as a novel hardware-assisted active triggering mode, which reduces DAQ computing load and network bandwidth outside triggered time windows.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Performance and reliability of β-Ga 2 O 3 Schottky barrier diodes at high temperature

Beta-gallium oxide (ß-Ga 2 O 3 ) is an ultrawide bandgap semiconductor that has potential for power electronic applications and devices operating at high temperatures. Particularly important for these applications are its 4.9 eV bandgap, facile electron doping, and the ability to grow ß-Ga 2 O 3 crystals from the melt. In this work, vertical ß-Ga 2 O 3 Schottky barrier diodes were fabricated using Pt Schottky and Ti-based Ohmic contacts and Au contact pads on unintentionally doped n-type, (2¯01)-oriented single crystal substrates. The diode’s temperature-dependent electrical properties up to 400°C were investigated, and the Pt/Ga 2 O 3 Schottky barrier height was determined to be close to 1.2 eV. The degradation of the contacts over multiple cycles up to 400°C was observed, resulting in a significant increase in series resistance of the diodes by 1000× at ambient temperature after they were cycled. According to electron microscopy measurements, this degradation is likely due in part to the migration and oxidation of Ti at the top surface of the Au contact pads. This degradation highlights the need for further research and development to ensure stable Ohmic and Schottky contacts to Ga 2 O 3 at temperatures above 400°C.

36 MATERIALS SCIENCE↗

Improving Interface Stability of Si Anodes by Mg Coating in Li-Ion Batteries

Silicon (Si) is a promising anode material for high-energy-density lithium-ion batteries (LIBs), but its short calendar life and poor cycling performance prevent its large-scale adoption. Introducing magnesium (Mg) salt into the electrolyte has been recently shown to form a ternary Li–Mg–Si Zintl phase upon lithiation of Si and improve the cycling performance. However, the ternary Zintl phase formation mechanism and its impact on the solid electrolyte interphase (SEI) are not yet well understood. In this work, we demonstrate the formation of a ternary Li–Mg–Si Zintl phase by Mg coating of the Si anode, where Mg diffuses into the Si film upon deposition and intermixes further during the lithiation process. The presence of the Zintl phase improves the interface stability, alters the nature of the SEI, and enhances the cycling performance of the Si anode. This study provides insights into the formation mechanism of the ternary Zintl phase and guidelines for the future design of Si anodes.

25 ENERGY STORAGE↗

Microscopic Observation of Solid Electrolyte Interphase Bilayer Inversion on Silicon Oxide

Silicon has been investigated in recent years as an alloying anode material to enhance gravimetric energy density in lithium-ion batteries. Although recent developments have suggested that silicon oxides exhibit improved cycling stability over pure Si, the origin of the improved cycling performance is still poorly understood. The initial solid electrolyte interphase (SEI) formation mechanisms on Si wafers with both native oxide and chemically etched thermal oxide coatings are investigated structurally, chemically, and morphologically in the nanoscale. After one electrochemical cycle, microscopy reveals that SEI formed on native SiO x features the typical SEI bilayer structure with a carbon-rich outer SEI layer and an inorganic-rich inner SEI layer. In contrast, the SEI formed on chemically etched thermal oxide shows an inversion in the structure. This work observes distinct initial SEI formation mechanisms on the HF-etched SiO 2 surface, which may be partially responsible for improved cycle life observed in SiO x -based anode materials.

25 ENERGY STORAGE↗

Evolution of solid electrolyte interphase and active material in the silicon wafer model system

Alloying anode materials for lithium-ion batteries, such as silicon (Si), are an important focus of materials research due to the demand for increased energy density for electric vehicles and stationary grid storage. However, progress towards next generation anode materials has been hindered by poor capacity retention due to the instability of the Si active material and the solid electrolyte interphase (SEI). Herein, the evolution of the active Si material and the SEI are simultaneously investigated from the perspective of chemical, structural, morphological, and electronic evolution in the Si wafer model system through its cycling life, using time-of-flight secondary ion mass spectrometry (TOF-SIMS), scanning transmission electron microscopy (STEM), atomic force microscopy (AFM), and scanning spreading resistance microscopy (SSRM). The results illustrate a dynamic evolution of the SEI and active Si material through cycling. Through an improved understanding of evolution of SEI and Si active material within the Si wafer model system, mitigation strategies may be designed to extend the lifetime of Si anodes.

25 ENERGY STORAGE↗

High-Temperature Nucleation of GaP on V-Grooved Si

The use of nanopatterned {111}-faceted v-grooves has recently shown promise for growing high-quality III–V material on Si. Here, we study the effect of reactor conditions and surface pretreatments on the nucleation of GaP on v-grooved Si in a high-temperature regime, which offers the promise of a defect-free GaP/Si interface favorable for Si passivation and dislocation glide in the GaP. X-ray photoelectron spectroscopy was used to understand the Si surface chemistry prior to nucleation, and transmission electron microscopy was used to probe material quality of the nuclei. Temperature and V/III ratio were found to control the facet selectivity of nucleation. We demonstrate a condition of high temperature and high V–III ratio that leads to uniform nucleation at the bottom of the trenches, with initial material free of nucleation-related interfacial defects. This optimized condition was then shown to coalesce into a thin film after additional growth.

36 MATERIALS SCIENCE↗

Snowmass Letter of Interest - Cloud Computing - CompF4

The world currently spends more than $30B per quarter on the consumption of Cloud Computing services. This is 17 times the size of the entire FY20 budget for the Office of Science at the Department of Energy. These resources have been successfully used for scientific computing in HEP and elsewhere under a pay-as-you-go model where users are billed monthly based on the resources they have consumed. There are a wide range of Cloud services, but we categorize them into “capability” and “capacity”. Capability services represent a unique set of features that we have not provisioned on-premises for a variety of reasons (cost-effectiveness, power consumption, proprietary solutions, etc.) Capacity services are services that allow us to scale out commodity services; historically we have focused on high-throughput (batch) computing.

97 MATHEMATICS AND COMPUTING↗

Sputtered p-Type Cu x Zn 1– x S Back Contact to CdTe Solar Cells

As thin-film cadmium telluride (CdTe) solar cells gain prominence, one particular challenge is optimizing contacts and their interfaces to transfer charge without losses in efficiency. Back contact recombination is still significant and will prevent CdTe solar technology from reaching its full potential in device efficiency, and transparent back contacts have not been developed for bifacial solar technology or multijunction solar cells. To address these challenges, here we investigate sputtered Cu x Zn 1– x S as a p-type semi-transparent back contact material to thin-film polycrystalline CdTe solar cells at Cu concentrations x = 0.30, 0.45, and 0.60. This material is selected for its high hole conductivity (160–2120 S cm –1 ), wide optical band gap (2.25–2.75 eV), and variable ionization potential (approximately 6–7 eV) that can be aligned to that of CdTe. We report that without device optimization, CdTe solar cells with these Cu x Zn 1– x S back contacts perform as well as control cells with standard ZnTe:Cu back contacts. We observe no reduction in external quantum efficiency, low contact barrier heights of approximately 0.3 eV, and carrier lifetimes on par with those of baseline CdTe. These cells are relatively stable over one year in air, with V OC and efficiency of the x = 0.30 cell decreasing by only 1 and 3%, respectively. Using scanning electron microscopy and scanning transmission electron microscopy to investigate the Cu x Zn 1– x S/CdTe interface, we demonstrate that the Cu x Zn 1– x S layer segregates into a bilayer of Cu-Te-S and Zn-Cd-S, and thermodynamic reaction calculations support these findings. Despite its bilayer formation, the back contact still functions well. This investigation explains some of the physical mechanisms governing the device stack, inspires future work to understand interfacial chemistry and charge transfer, and elicits optimization to achieve higher-efficiency CdTe cells.

14 SOLAR ENERGY↗

Heteroepitaxial Integration of ZnGeN 2 on GaN Buffers Using Molecular Beam Epitaxy

Recently theorized hybrid II-IV-N 2 /III-N heterostructures, based on current commercialized (In,Ga)N devices, are predicted to significantly advance the design space of highly efficient optoelectronics in the visible spectrum, yet there are few epitaxial studies of II-IV-N 2 materials. In this work, we present heteroepitaxial ZnGeN 2 grown on GaN buffers and AlN templates. We demonstrate that a GaN nucleating surface is crucial for increasing the ZnGeN 2 crystallization rate to combat Zn desorption, extending the stoichiometric growth window from 215 degrees C on AlN to 500 degrees C on GaN buffers. Structural characterization reveals well-crystallized films with threading dislocations extending from the GaN buffer. These films have a critical thickness for relaxation of 20-25 nm as determined by reflection high energy electron diffraction (RHEED) and cross-sectional scanning electron microscopy (SEM). The films exhibit a cation-disordered wurtzite structure, with lattice constants a = 3.216 +/- 0.004 A and c = 5.215 +/- 0.005 A determined by RHEED and X-ray diffraction (XRD). This work demonstrates a significant step toward the development of hybrid ZnGeN 2 -GaN integrated devices.

36 MATERIALS SCIENCE↗

Growth of GaAs on single-crystal layered-2D Bi 2 Se 3

This article demonstrates the successful growth of cubic GaAs (111) on single-crystal 2D layered Bi 2 Se 3 (0001) substrates achieved using a cubic ZnSe buffer layer. This growth sequence was chosen based upon observed reactions between Bi 2 Se 3 (0001) substrates and both Ga and Zn. For the conditions used in our MOCVD reactor, triethylgallium (TEGa) interacts strongly with Bi 2 Se 3 to form Ga 2 Se 3 , which can disrupt the nucleation and growth of GaAs. Therefore, a buffer layer is needed which prevents Ga-Bi 2 Se 3 interactions while simultaneously providing a suitable growth surface for GaAs. ZnSe was chosen because it is lattice-matched to GaAs, and can be created by annealing the Bi2Se3 under a diethylzinc (DEZn) flux. A sample utilizing this growth sequence has been grown, characterized and exfoliated as a possible pathway toward reducing the substrate cost for III-V devices such as solar cells.

14 SOLAR ENERGY↗

Optical and Structural Properties of High-Efficiency Epitaxial Cu(In,Ga)Se 2 Grown on GaAs

Photovoltaic devices based on Cu(In,Ga)Se 2 (CIGS) usually employ polycrystalline thin films as the absorber layer. This is because, to date, the highest conversion efficiencies have been attained with polycrystalline CIGS films. Recently, Nishinaga et al. presented an epitaxial CIGS thin-film solar cell grown on a GaAs (100) substrate with a conversion efficiency of 20.0%. In this contribution, we study the optical and structural properties of this high-efficiency epitaxial film, along with others with different compositions using cathodoluminescence spectrum imaging and transmission electron microscopy. A comparison of the high-efficiency epitaxial film and a traditional polycrystalline film with a similar global composition reveals significant differences in microstructure and uniformity of emission properties despite similar performance. The analysis of epitaxial films with a higher gallium concentration indicates that the emission characteristics and nature of extended defects in epitaxial CIGS films are strongly dependent on the gallium content. The results presented here provide evidence that, with further optimization, photovoltaic conversion efficiencies of epitaxial CIGS films could exceed those of polycrystalline CIGS.

14 SOLAR ENERGY↗

From Modules to Atoms: Techniques and Characterization for Identifying and Understanding Device-Level Photovoltaic Degradation Mechanisms

This report documents how degraded modules are analyzed for the characterization of cell-level performance reduction. The primary degradation topics presented here are 1) potential-induced degradation, 2) defect metastability and impurity diffusion, and 3) partial-shading-induced reverse-bias breakdown. Imaging techniques, such as electroluminescence imaging, photoluminescence imaging, and lock-in thermography provide spatial information of full modules on the meter scale. Area of interest can then be imaged with higher spatial resolution by zooming in with fields of view near the mm scale. We document procedures for coring cell samples from selected regions of interest using mechanical drilling. The small samples are then of suitable size for various microscopic analyses using techniques such as scanning electron microscopy, time-of-flight secondary ion spectrometry, atomic force microscopy, electron beam induced current, transmission electron microscopy, and atom probe tomography, which can provide chemical, structural, and electrical characterization down to the atomic scale.

14 SOLAR ENERGY↗