Search NASA⌕ Search

Engineering topics

Novitski, Igor

Publications and source records attributed to Novitski, Igor.

At least 19 records

Testing high-current superconducting subscale dipole coils with superconducting transformer

Several sub-scale superconducting dipole coils are being developed at Fermilab in the framework of the U.S. Magnet Development Program. These coils are made of high-current LTS and HTS cables with maximum currents of up to 10 kA. A superconducting current transformer with a maximum DC current up to ~25 kA previously developed at Fermilab for Nb3Sn Rutherford cable testing was modified and adapted for small dipole coil testing. This paper describes its commissioning using a NbTi dipole magnet impregnated with TELENE. This magnet was wound out of 6/1 NbTi cable.

Barzi, Emanuela↗

Development and test of a large-aperture Nb3Sn cos-theta dipole coil with stress management

The stress-managed cos-theta (SMCT) coil is a new concept which was proposed and is being developed at Fermilab in the framework of US Magnet Development Program (US-MDP) for high-field and/or large-aperture accelerator magnets based on low-temperature and high-temperature superconductors. A 120-mm aperture two-layer Nb3Sn SMCT dipole coil has been developed at Fermilab to demonstrate and test the SMCT concept including coil design, fabrication technology and performance. The first SMCT demo coil was fabricated and assembled with 60-mm aperture Nb3Sn coil inside a dipole mirror configuration and tested separately and in series with the insert coil. This paper summarizes the design, parameters, and quench performance of the 120-mm aperture SMCT coil in a dipole mirror configuration.

43 PARTICLE ACCELERATORS↗

Development of a Bi2212 Dipole Insert at Fermilab

A goal of the U.S. Magnet Development Program (US-MDP) is high-field magnets for accelerators with magnetic fields larger than 15 T, i.e., above the limits of Nb 3 Sn accelerator magnets. Composite round wires and Rutherford cables made of high temperature superconductor Bi2212 may achieve this goal. Bi2212 is sensitive to transverse stresses and strains, and this requires stress management in the coil design. A stress management approach was developed at Fermilab for high-field large-aperture Nb 3 Sn accelerator magnets. Now it is being applied to high-field dipole insert coils based on Bi2212 Rutherford cable. Here this paper describes the insert coil design and main parameters, including the superconducting wire and cable. The coil will be installed inside a 60-mm bore Nb 3 Sn dipole outsert coil and cold iron yoke. The Bi2212 coil will be tested individually and in series with the Nb 3 Sn outsert coil. The expected Bi2212 insert test parameters are reported and discussed.

43 PARTICLE ACCELERATORS↗

Design and Assembly of a Large-Aperture Nb 3 Sn Cos-Theta Dipole Coil With Stress Management in Dipole Mirror Configuration

The stress-management cos-theta (SMCT) coil is a new concept which has been proposed and is being developed at Fermilab in the framework of US Magnet Development Program (US-MDP) for high-field and/or large-aperture accelerator magnets based on low-temperature and high-temperature superconductors. The SMCT structure is used to reduce large coil deformations under the Lorentz forces and, thus, the excessively large strains and stresses in the coil. A large-aperture Nb 3 Sn SMCT dipole coil has been developed and fabricated at Fermilab to demonstrate and test the SMCT concept including coil design, fabrication technology and performance. The first SMCT coil has been assembled with 60-mm aperture Nb 3 Sn coil inside a dipole mirror configuration and will be tested separately and in series with the insert coil. Here this paper summarizes the large-aperture SMCT coil design and parameters and reports the coil fabrication steps and its assembly in dipole mirror configuration.

43 PARTICLE ACCELERATORS↗

Conceptual Design of 20 T Hybrid Accelerator Dipole Magnets

Hybrid magnets are currently under consideration as an economically viable option towards 20 T dipole magnets for next generation of particle accelerators. In these magnets, High Temperature Superconducting (HTS) materials are used in the high field part of the coil with so-called insert coils, and Low Temperature Superconductors (LTS) like Nb 3 Sn and Nb-Ti superconductors are used in the lower field region with so-called outsert coils. The attractiveness of the hybrid option lays on the fact that, on the one hand, the 20 T field level is beyond the Nb 3 Sn practical limits of 15-16 T for accelerator magnets and can be achieved only via HTS materials; on the other hand, the high cost of HTS superconductors compared to LTS superconductors makes it advantageous exploring a hybrid approach, where the HTS portion of the coil is minimized. Here we present in this paper an overview of different design options aimed at generating 20 T field in a 50 mm clear aperture. The coil layouts investigated include the Cos-theta design (CT), with its variations to reduce the conductor peak stress, namely the Canted Cos-theta design (CCT) and the Stress Management Cos-theta design (SMCT), and, in addition, the Block-type design (BL) including a form of stress management and the Common-Coil design (CC). Results from a magnetic and mechanical analysis are discussed, with particular focus on the comparison between the different options regarding quantity of superconducting material, field quality, conductor peak stress, and quench protection.

43 PARTICLE ACCELERATORS↗

Development of a 120-mm Aperture Nb 3 Sn Dipole Coil With Stress Management

This paper describes a 120-mm aperture 2-layer dipole coil with stress management (SM) developed at Fermilab based on cos-theta coil geometry. A model of the coil support structure made of plastic was printed using additive manufacturing technology and used for practice coil winding. The real coil support structure was printed using the 316 stainless steel. The results of the SM structure size control and the key coil fabrication steps are reported in the paper. Finally, the design of coil SM structure and the coil FEA in the dipole mirror test configurations are presented and discussed.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

MDPCT1 Quench Data and Performance Analysis

MDPCT1 is a four-layer cos-theta Nb3Sn dipole demonstrator developed and tested at FNAL in the framework of the U.S. Magnet Development Program. The magnet reached record fields for accelerator magnets of 14.1 T at 4.5 K in the first test and 14.5 T at 1.9 K in the second test and then showed large degradation. While its inner coils performed exceptionally well with only two quenches up to 14.5 T and no evidence of degradation, the outer coils degraded over the course of testing. By adopting new measurement and analysis techniques at FNAL we are discussing in detail what happened. Both success and failure in our diagnostics are discussed. The evolution of techniques over the course of two tests (and three thermal cycles) shows the path to address challenges brought by the first four-layer magnet tested at FNAL. This paper presents the analysis of quench data along with diagnostic features and complementary measurements taken in support of the magnet performance analysis.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Conceptual Design of a HTS Dipole Insert Based on Bi2212 Rutherford Cable

The U.S. Magnet Development Program (US-MDP) is aimed at developing high-field accelerator magnets with magnetic fields beyond the limits of Nb 3 Sn technology. Recent progress with composite wires and Rutherford cables based on the first generation high-temperature superconductor Bi 2 Sr 2 CaCu 2 O 8-x (Bi2212) allows considering them for this purpose. However, Bi2212 wires and cables are sensitive to transverse stresses and strains, which are large in high-field accelerator magnets. This requires magnet designs with stress management concepts to control azimuthal and radial strains in the coil windings and prevent the degradation of the current carrying capability of Bi2212 conductor or even its permanent damage. This paper describes a novel stress management approach, which was developed at Fermilab for high-field large-aperture Nb 3 Sn accelerator magnets, and is now being applied to high-field dipole inserts based on Bi2212 Rutherford cables. The insert conceptual design and main parameters, including the superconducting wire and cable, as well as the coil stress management structure, key technological steps and approaches, test configurations and their target parameters, are presented and discussed.

43 PARTICLE ACCELERATORS↗

First Field Measurements of the 15 T Nb 3 Sn Dipole Demonstrator MDPCT1

Within the US Magnet Development Program (MDP) a 15 T Nb 3 Sn dipole was developed, to demonstrate a magnet design for a post-LHC pp Collider. Specifically, the magnet design is based on 60 mm aperture 4-layer shell-type coils, graded between the inner and outer layers to maximize the magnet performance. The cable in the two innermost layers has 28 strands 1.0 mm in diameter and the cable in the two outermost layers has 40 strands 0.7 mm in diameter. Both cables use RRP Nb3Sn wires produced by Bruker-OST. Magnet coils are surrounded by vertically-split thick iron laminations, con-nected by aluminum I-clamps, and a thick stainless-steel skin. The magnet was tested at the Vertical Magnet Test Facility (VMTF) at Fermilab. This paper reports the first results of magnetic measure-ments of the 15 T Nb 3 Sn dipole demonstrator including geometrical harmonics, coil magnetization and iron saturation effects. The ex-perimental data are compared with the magnetic calculations.

43 PARTICLE ACCELERATORS↗

Fermilab Superconducting Nb₃Sn High Field Magnet R&D Program

Magnets based on the modern Nb₃Sn conductor are the main candidates for future high-energy hadron colliders. Fermilab as part of the U.S. MDP executes an extensive R&D program on these high-field magnets. This program includes basic conductor and material R&D, quench per-formance studies, and building a meter-long high-field demonstrator. This paper summarizes the current status of the program including its recent results.

43 PARTICLE ACCELERATORS↗

Measurements and Modeling of Mechanical Properties of Nb 3 Sn Strands, Cables, and Coils

High field Nb 3 Sn magnets for the next generation of hadron colliders are known to have long trainings and to be limited at 90% of their short sample limit at best. This means that the conductor current is at 60% or less of its critical value. Homogeneous finite element models are typically used for the complex system that includes coils, wedges, poles, yoke, rods, keys, shoes, fillers, shell, etc. Through both modeling and measurements of mechanical properties, we show how a more accurate sub-modelling of the composite structure allows for a better understanding of the stress and strain distributions. This is extremely important for Nb3Sn performance since state-of-the-art high critical current wires of this superconductor are particularly sensitive to strain.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Assembly and Tests of Mechanical Models of the 15-T Nb 3 Sn Dipole Demonstrator

Within the US Magnet Development Program, Fermilab is developing a 15-T Nb 3 Sn dipole demonstrator. Prior to the construction of the real magnet model, short sections and the whole structure were instrumented with strain gauges and assembled to confirm the results of structural analysis, check tooling and to gain experience with the assembly of the real magnet components. We summarize the lessons learned from these mechanical models and compares the measured data with the finite element analysis.

43 PARTICLE ACCELERATORS↗

The 16 T dipole development program for FCC and HE-LHC

A future circular collider (FCC) with a center-of-mass energy of 100 TeV and a circumference of around 100 km, or an energy upgrade of the LHC (HE-LHC) to 27 TeV require bending magnets providing 16 T in a 50-mm aperture. Several development programs for these magnets, based on Nb$_3$Sn technology, are being pursued in Europe and in the U.S. In these programs, cos-theta, block-type, common-coil, and canted-cos-theta magnets are explored; first model magnets are under manufacture; limits on conductor stress levels are studied; and a conductor with enhanced characteristics is developed. This paper summarizes and discusses the status, plans, and preliminary results of these programs.

43 PARTICLE ACCELERATORS↗

Mechanical Utility Structure for Testing High Field Superconducting Dipole Magnets

The U.S. Magnet Development Program (MDP) collaboration is designing a utility mechanical structure for testing various high-field superconducting dipole coils. The design uses a shell-based structure concept, which allows applying preload in two steps: During a room temperature assembly and during a cool down to a cryogenic temperature. The structure is designed to accommodate various coil designs - including Nb 3 Sn Cosine Theta (CT) and Canted CT magnets as well as hybrid magnets with high temperature superconductor cables. Superconducting coils, enclosed by bolted pads to form an octagonal coil pack, will be inserted into a reusable yoke-shell subassembly and precisely preloaded during the assembly using a bladder-and-key technology. Due to a differential thermal contraction between an external aluminum shell and the magnet core, the coil preload increases during the cool down up to level required for 17-T excitation. Such a reusable structure will serve as a testing fixture supporting goals of the MDP program, decreasing cost and simplifying coil performance testing at different preload levels. We present a finite-element analysis of the structure preloading various coil designs and examine the predicted coil stress at each step of the magnet assembly and excitation.

43 PARTICLE ACCELERATORS↗

FEA Model and Mechanical Analysis of the Nb 3 Sn 15-T Dipole Demonstrator

Nb$_{3}$Sn magnets with a nominal operation field of ~15 T are being considered for the large hadron collider (LHC) energy upgrade high-energy large hadron collider (HE-LHC) and a post-LHC future circular collider. To demonstrate the feasibility of 15-T accelerator quality dipole magnets, the U.S. magnet development program is developing a single-aperture 15-T Nb$_{3}$Sn dipole demonstrator based on a 4-layer graded cos-theta coil with 60 mm aperture and cold iron yoke. The main design challenges for 15-T accelerator magnets include large Lorentz forces at this field level. To counteract them, an innovative mechanical structure based on a vertically split iron yoke, locked by large aluminum IC-clamps and supported by a thick stainless steel skin, has been developed at Fermilab. To study the performance of the structure, a parametric multiphysics finite element analysis (FEA) model has been set up. This paper describes the numerical model as well as the results of a sensitivity analysis of the effect of geometrical tolerances and assembly parameters.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Measurements of Dynamic Effects in FNAL 11 T Nb 3 Sn Dipole Models

Fermilab, in collaboration with CERN, has developed a twin-aperture 11 T Nb 3 Sn dipole suitable for the high-luminosity LHC upgrade. During 2012-2014, a 2-m long single-aperture dipole demonstrator and three 1-m long single-aperture dipole models were fabricated by FNAL and tested at its Vertical Magnet Test Facility. Collared coils from two of the 1-m long models were then used to assemble the first twin-aperture dipole demonstrator. This magnet had extensive testing in 2015-2016, including quench performance, quench protection, and field quality studies. Here, this paper reports the results of measurements of persistent current effects in the single-aperture and twin-aperture 11 T Nb 3 Sn dipoles and compares them with similar measurements in previous NbTi magnets

43 PARTICLE ACCELERATORS↗

Status of the 16 T Dipole Development Program for a Future Hadron Collider

A next step of energy increase of hadron colliders beyond the LHC requires high-field superconducting magnets capable of providing a dipolar field in the range of 16 T in a 50-mm aperture with accelerator quality. These elements could meet the requirements for an upgrade of the LHC to twice the present beam energy or for a 100-TeV center of mass energy future circular collider. Here, we summarize the activities and plans for the development of these magnets, in particular within the 16 T Magnet Technology Program, the WP5 of the EuroCirCol, and the U.S. Magnet Development Program.

43 PARTICLE ACCELERATORS↗

Energy Production Demonstrator and Material Testing Station optimization for Megawatt proton beams

A simulation study of the Energy Production Demonstrator (EPD) concept – a solid heavy metal target irradiated by GeV-range intense proton beams and producing more energy than consuming – is carried out. Neutron production, fission, energy deposition, energy gain, testing volume and helium production are simulated using the MARS15 code for tungsten, thorium, and natural uranium targets in the proton energy range 0.5–120 GeV. This study shows that the proton energy range of 2–4 GeV is optimal for both a nat U EPD and the tungsten-based testing station for proton accelerator facilities. Simulation-based conservative estimates not including breeding and fission of plutonium suggest the proton beam current sufficient to produce 1 GW of thermal output power with the nat U EPD while supplying a relatively small fraction of that power to operate the accelerator. The thermal analysis has been performed and has shown that the EPD with a parallel proton beam feeding the core has a potential problem due to a possible core meltdown. In conclusion, a scheme has been proposed with a beam steering on the outer surface of the target; its thermal analysis indicates that slicing the target in shorter parts and maintaining a temperature of 25 °C on their surfaces would to avoid the target meltdown.

43 PARTICLE ACCELERATORS↗