Engineering topics

Nuttall, David [ORNL] (ORCID:0000000164167553)

Publications and source records attributed to Nuttall, David [ORNL] (ORCID:0000000164167553).

3 records

DOE OSTI2026

Demonstration of high-rate manufacturing of π-joint using additive manufacturing

Bonded composite π-joints are critical to support wing geometries in aerospace/aircraft structures. Its lightweight and robust load-bearing capabilities/design guarantee high structural integrity and reliability. Current manufacturing techniques of π-joints are complex and laborious, and do not always offer high-quality joining. This study presents a high-rate manufacturing approach to fabricate π-joints using an integrated Additive Manufacturing and Compression Molding (AMCM) process. The joints were manufactured using unidirectional aerospace-grade LMPAEK/CF at 60% fiber loading for the stiffeners/skin and LM-PAEK/GF as the adhesive and characterized to evaluate their microstructure and strength. While the results indicate void formation at the joint caused by inadequate pressure, the peak tensile load of 600N recorded is akin to injection-autoclave molded π-joints, which validates the potential of this high-rate integrated approach to eliminate time-consuming and labour-intensive processes of making π-joints to reduce cost and produce high-quality joints.

Marathe, Umesh [ORNL]↗

DOE OSTI2026

Influence of Surface Treatment on the Interfacial and Mechanical Performance of Metal-Insert Overmolded Composites

Structural composites with metal inserts are gaining increasing interest enabling light weight design for energy efficiency, provide insulation, corrosion protection without compromising mechanical integrity. Such over molded metal-polymer composites show strong potential in many automotive and aerospace component parts, e.g. car bumper, chassis, door, brackets, fasteners, etc. Despite several advantages, metal-polymer dissimilar interface remains a weak spot in structural design, requiring further investigation to improve interfacial interlocking. The current work focuses on enhancing the metal-polymer adhesion between stainless steel inserts and polymer matrices (e.g. acrylonitrile butadiene styrene resin (ABS), and polyamide 66 (PA66) through surface treatment via chemical etching and mechanical roughening. In the chemical etching process, metal substrates were treated with aqua regia solution for different time intervals to evaluate surface roughness measured by water contact angle and morphology analysis. For mechanical roughening approach, metal inserts were subjected to blasting for surface abrasion. Treated samples were also functionalized with aminosilane coupling agent which showed successful grafting on the surface measured by water contact angle. Metal inserts with micro level surface roughness through etching exhibited significant 21% improvement in adhesion strength compared to untreated inserts; however, the effect of silane treatment on the interfacial strength was found to be highly matrix dependent.

Saha, Subhabrata [ORNL] (ORCID:000000033966064X)↗

DOE OSTI2025

Multiplexing core & sheath extrusion system development for additive manufacturing for inner-bead multi-material capability

Single-feed polymer extruders are widely used in large-format additive manufacturing (AM) systems; however, the increasing demand for multi-material functionality within a single part has driven significant innovation in this field. One approach involves robotic pick-and-place operations, while another explores mechanical switching of feed lines during extrusion. Although robotic pick-and-drop systems offer flexibility, they introduce longer layer times during material changes, which can negatively affect the structural integrity of the part. On the other hand, mechanical feed switching causes delays in material transitions, as the existing material must be flushed before the new material emerges from the nozzle. This poses particular challenges for smaller or more intricate parts. In this study we are developing a unique multiplexing extrusion system with core & sheath nozzle that combines two extruders via co-extrusion. This allows for a unique inside and outside inner-bead (i.e., within the same bead) multi-material capability. We believe that this technology will allow for combining neat and filled materials, ductile and stronger materials, and many other combinations to address the problems aforementioned above and disrupt the AM technology creating new opportunities and opening application areas.

Tekinalp, Halil [ORNL]↗