Engineering topics

O'Connor, D.

Publications and source records attributed to O'Connor, D..

23 records · Page 2

NASA NTRS1991

Advances in high temperature components for AMTEC (Alkali Metal Thermal-to-Electric Converter)

The basic performance of Alkali Metal Thermal-to-Electric Converter (AMTEC) cells is well understood, and quantitative modeling of the electrode performance has been carried out. Tests have been carried out to evaluate the high temperature performance of critical AMTEC components. Progress made in understanding the relative performance of AMTEC components, such as electrodes, electrolytes, working fluids, and seals, as device operating temperature is varied is discussed. Most metallic components are especially subject to corrosion in hot liquid alkali metals containing dissolved oxides. Stability issues of AMTEC components may be addressed by life testing, accelerated testing, and modeling based on known kinetic and thermochemical data.

Williams, R. M.↗

NASA NTRS1991

Directly deposited current collecting grids for AMTEC electrodes

Current collection in electrodes for the alkali metal thermal to electric converter (AMTEC) has been improved by using molybdenum grids to decrease sheet and contact resistance in RhW and PtW electrodes. The grids are directly deposited on the solid electrolyte either by sputter- or photodeposition. Comparison of electrodes having such underlying grids with those without such grids has shown power produced in an AMTEC cell to be increased by as much as 35 percent.

Ryan, M. A.↗

NASA NTRS1990

Thermal characterization of an AMTEC recirculating test cell

An alkali metal thermoelectric converter (AMTEC) recirculating test cell has been operated in order to determine the magnitudes of the primary heat losses of the cell and the value of the emissivity of the condenser surface. The energy balance included radiation losses, conductive losses, and losses due to the flow of sodium into the cell. The radiative heat flux dominated the heat loss mechanism of the cell at open circuit, and the condenser emissivity was calculated to be about 0.1. It is shown that, if this emissivity can be reduced to 0.02, then parasitic losses in an AMTEC recirculating test cell operating near peak power would be less than 40 percent of the heat required by the cell. The condenser emissivity decreases with elapsed time, resulting in improved thermal performance of the cell.

Underwood, M. L.↗

NASA NTRS1990

Lifetime studies of high power rhodium/tungsten and molybdenum electrodes for application to AMTEC (alkali metal thermal-to-electric converter)

A detailed and fundamental model for the electrochemical behavior of AMTEC electrodes is developed which can aid in interpreting the processes which occur during prolonged operation of these electrodes. Because the sintering and grain growth of metal particles is also a well-understood phenomenon, the changes in electrode performance which accompany its morphological evolution may be anticipated and modeled. The grain growth rate observed for porous Mo AMTEC electrodes is significantly higher than that predicted from surface diffusion data obtained at higher temperatures and incorporated into the grain growth model. The grain growth observed under AMTEC conditions is also somewhat higher than that measured for Mo films on BASE (beta-alumina solid electrolyte) substrates in vacuum or at similar temperatures. Results of modeling indicate that thin Mo electrodes may show significant performance degradation for extended operation (greater than 10,000 h) at higher operating temperatures (greater than 1150 K), whereas W/Rh and W/Pt electrodes are expected to show adequate performance at 1200 K for lifetimes greater than 10,000 h. It is pointed out that current collection grids and leads must consist of refractory metals such as Mo and W which do not accelerate sintering or metal migration.

Williams, R. M.↗

NASA NTRS1989

AMTEC recirculating test cell component testing and operation

Alkali metal thermoelectric converter operation in a recirculating test cell (RTC), which requires a small electromagnetic pump (EM) and a high-temperature beta-double-prime alumina-solid-electrolyte (BASE)-to-metal seal, is discussed. The design of a pump and an active metal braze seal and the initial operation of a cell using these components are described. The pump delivered 0.25 cu cm/min against a 28-psia head. A braze seal system was selected after shear strength tests of Ta or Nb brazed to BASE by a variety of fillers including TiCuNi, TiNi, and TiNiCr. The TiCuNi filler was chosen for environment cell testing and showed no failure or observable degradation after short-term tests up to 1055 K. The pump and the Nb/TiCuNi/BASE seal were used in a test that demonstrated all the operational functions of the RTC for the first time. An increase in the radiation reduction factor at constant input power was observed, indicating that the condenser was being wet by sodium resulting in an increased reflectivity.

Underwood, M. L.↗