Engineering topics

O'Donnell, Tim

Publications and source records attributed to O'Donnell, Tim.

9 records

NASA NTRS1991

Erosion of carbon/carbon by solar wind charged particle radiation during a solar probe mission

The possible erosion of a carbon/carbon thermal shield by solar wind-charged particle radiation is reviewed. The present knowledge of erosion data for carbon and/or graphite is surveyed, and an explanation of erosion mechanisms under different charged particle environments is discussed. The highest erosion is expected at four solar radii. Erosion rates are analytically estimated under several conservative assumptions for a normal quiet and worst case solar wind storm conditions. Mass loss analyses and comparison studies surprisingly indicate that the predicted erosion rate by solar wind could be greater than by nominal free sublimation during solar wind storm conditions at four solar radii. The predicted overall mass loss of a carbon/carbon shield material during the critical four solar radii flyby can still meet the mass loss mission requirement of less than 0.0025 g/sec.

Sokolowski, Witold↗

NASA NTRS1991

Qualification of uralane 5750 A/B (LV) for flight applications

Uralane 5750 A/B (LV) is a POLYURETHANE which was to be considered for use as a thin CONFORMAL COATING on printed circuit boards for JPL flight projects. As part of the qualification process several properties of Uralane 5750 A/B (LV) were measured for the as-cured material and after various environmental exposures. The properties that were measured included outgassing i.e. Total Mass Loss (TML) and Vacuum Condensable Mass (VCM) and mass accumulation rates on cold surfaces, Static Elastic Modulus and coefficient of Thermal Expansion (CTE). The Uralane 5750 A/B (LV) that was tested consisted of sheets which varied in both thickness and curing procedures. The environmental exposures consisted of vacuum, thermal and combined thermal vacuum. The physical properties of Uralane 5750 A/B (LV) met the JPL requirements for flight in both the as-cured condition and after environmental exposures.

Lewis, Donald F.↗

NASA NTRS1990

The effect of nitric acid exposure on Galileo spacecraft titanium alloy Ti-6Al-4V propellant tanks

The Ti-6Al-4V-constructed retropropulsion-module tanks of the Galileo spacecraft were purged with nitrogen tetroxide in order to wait out a major launch rescheduling; nitric acid is among the residual products of such an operation. A test program was conducted on representative samples to ascertain the fracture toughness and stress corrosion threshold of the tanks' material, in view of Space Shuttle safety and mission-reliability requirements. It was found that the tanks' structural integrity was not degraded by nitric acid exposure.

Hsieh, Cheng↗

NASA NTRS1989

Cathode and insulator materials for a 30 kW arcjet thruster

This paper describes past experience with 30 kW arcjet engines, emphasizing the operational parameters pertinent to the selection of new/alternate erosion-resistant materials to enhance lifetime. Mechanisms of mass loss from the electrodes and insulators are suggested, and ways of identifying potential processes for controlling cathode erosion and insulator degradation are proposed. The limitations of present materials used in critical arcjet thruster components are described. An outline is given of the criteria and the figure of merit on which the selection of candidate materials can be based. Potentially useful new/alternate materials are listed based on available thermophysical and other material properties.

Sokolowski, Witold↗

NASA NTRS1989

Failure analysis of blistered gold plating on spot welded electrical relays

Gold-plated stainless-steel sideplates, part of a JPL Galileo spacecraft electronic-relay assembly, exhibited blistering after resistance spot welding. Unacceptable relays had heavy nonuniform gold electrodeposited layers with thicknesses 4.5-11.5 microns. SEM and metallographic investigations indicated much higher heat input generated during the resistance spot welding in unacceptable relays. The attributes of acceptable welded relays are contrasted with unacceptable relays; the possible mechanism of laminar formation of polymeric material in the gold plating is discussed; and some recommendations are provided to prevent similar problems.

Sokolowski, Witold↗

NASA NTRS1989

Qualification of room-temperature-curing structural adhesives for use on JPL spacecraft

An evaluation is made of the comparative advantages of numerous room temperature-cure structural primers and adhesives applicable to spacecraft structures. The EA 9394 adhesive and BR 127 primer were chosen for use in all primary structure bonding on the Galileo spacecraft, in virtue of adequate room-temperature lap shear and peel strengths and superior mechanical properties above 200 F. EA 9394 also offers superior work life, shelf-life, and storage properties, by comparison with the EA 934 alternative.

Carpenter, Alain↗

NASA NTRS1989

Microsandwich cellular solids

This article introduces a new concept of microsandwiching in which the cell wall itself is a sandwich structure and is substantially stiffer. Some experimental results are presented to show the efficacy of this approach. A method for optimizing the design of honeycomb microsandwich is also briefly outlined.

Balakrishna Bhat, T.↗

NASA NTRS1988

Qualification of room-temperature-curing epoxy adhesives for spacecraft structural applications

An adhesive-bonding test program is being conducted in order to develop structural adhesives applicable to JPL spacecraft. A noteworthy application for such an adhesive will be JPL's Galileo mission, whose trajectory will involve the circumnavigation of the planet Venus prior to Jupiter rendezvous, and will accordingly require stringent temperature and radiation environment requirements. The baseline adhesive for the test program is the EA 934 room temperature-cure epoxy, which has been widely used as a 'space-qualified' material.

Carpenter, Alain↗

NASA NTRS1988

Long-lived thermal control materials for high temperature and deep space applications

Considerable effort has been put into developing thermal-control materials for the Galileo space-craft. This paper presents a summary of these findings to date with emphasis on requirements, testing and results for the post-Challenger Galileo mission. Polyimide film (Kapton), due to its inherent stability in vacuum, UV, and radiation environments, combined with good mechanical properties over a large temperature range, has been the preferred substrate for spacecraft thermal control materials. Composite outer layers, using Kapton substrates, can be fabricated to meet the requirements of severe space environments. Included in the processing of Kapton-based composite outer layers can be the deposition of metal oxide, metallic and/or polymeric thin-film coatings to provide desirable electrical, optical and thermo-optical properties. In addition, reinforcement of Kapton substrates with fabrics and films is done to improve mechanical properties. Also these substrates can be filled with varying amounts of carbon to achieve particular electrical properties. The investigation and material development reported on here has led to improved thermo-gravimetric stability, surface conductivity, RF transparency, radiation and UV stability, flammability and handle-ability of outer layer thermal control materials for deep space and near-sun spacecraft. Designing, testing, and qualifying composite thermal-control film materials to meet the requirements of the Galileo spacecraft is the scope of this paper.

Whitt, Robin↗