Engineering topics

O'Farrell, J. M.

Publications and source records attributed to O'Farrell, J. M..

4 records

NASA NTRS1991

Time accurate Navier-Stokes computations of solid rocket motor internal field joint cavity flows

The low-speed flow of combustion gases in the Space Shuttle Solid Rocket Motor (SRM) following ignition are investigated with a time-accurate CFD technique. The flow of the combustion gases is examined in the forward joint section of the SRM at 80 s after ignition with attention given to the amplification of existing 'organ-pipe' modes of 15, 30, and 45 Hz resulting from frequency lock-in with vortex-shedding modes. The CFD code employed is a multizone compressible Navier-Stokes flow solver using a finite-volume, upwind-biased, total-variation-diminishing scheme. The vortex-generated oscillations generated by the inhibitor and the cavity at the forward field joint are described in terms of amplitude and frequency and related to the flow dynamics in the SRM. Oscillations are shown to occur spontaneously when the trailing edge of the cavity at the joint is sharp and can be amplified if the unburned portion of the inhibitor protrudes into the flow.

Farr, Rebecca A.↗

NASA NTRS1990

Aerothermal environment induced by mismatch at the SSME main combustion chamber-nozzle joint

The computational study reported here is motivated by a Space Shuttle main engine hardware problem detected in post-flight and post-test inspections. Of interest are the potential for hot gas ingestion into the joint (G15) at the main combustion chamber-to-nozzle interface and the effect of particular goemetric nonuniformities on that gas ingestion. The flowfield in the G15 region involves supersonic flow past a rounded forward facing step preceded by a deep narrow cavity. This paper describes the physical problem associated with joint G15 and computational investigations of the G15 aerothermal environment. The associated flowfield was simulated in two and three space dimensions using the United Solutions Algorithm (USA) computational fluid dynamics code series. A benchmark calculation of experimentally measured supersonic flow over of a square cavity was performed to demonstrate the accuracy of the USA code in analyzing flows similar to the G15 computational flowfield. The G15 results demonstrate the mechanism for hot gas ingestion into the joint and reveal the sensitivity to salient geometric nonuniformities.

Mcconnaughey, H. V.↗

NASA NTRS1990

Time-accurate Navier-Stokes computations of classical two-dimensional edge tone flow fields

Time-accurate Navier-Stokes computations were performed to study a Class II (acoustic) whistle, the edge tone, and gain knowledge of the vortex-acoustic coupling mechanisms driving production of these tones. Results were obtained by solving the full Navier-Stokes equations for laminar compressible air flow of a two-dimensional jet issuing from a slit interacting with a wedge. Cases considered were determined by varying the distance from the slit to the edge. Flow speed was kept constant at 1750 cm/sec as was the slit thickness of 0.1 cm, corresponding to conditions in the experiments of Brown. Excellent agreement was obtained in all four edge tone stage cases between the present computational results and the experimentally obtained results of Brown. Specific edge tone generated phenomena and further confirmation of certain theories concerning these phenomena were brought to light in this analytical simulation of edge tones.

Liu, B. L.↗

NASA NTRS1990

Reduction of vortex-induced vibration in vane geometries

Computations using a time-accurate, compressible Navier-Stokes flow model were conducted to analyze both unsteady laminar and turbulent flows over two curved configurations of vanes which were shaped to treat a 4.0 kHz vibration problem which has occurred in several SSMEs. This problem involves vortex shedding from vanes which causes excessive vane vibration and cracking. The original vane configuration exhibited strong flow-induced vibrations at a Strouhal number near 0.19 for a the first bending mode excitation. Scalloping of the leading edge raised the frequency of the vane's first torsional mode, which in turn increased the onset flow velocity at lock-in. Beveling the vane's trailing edge eliminated vortex shedding at the trailing edge, which decoupled the flow oscillation from the vibrating wave. A modified vane configuration with a beveled trailing edge at a 30 deg angle was also studied.

Liu, B. L.↗