Effect of a Nitrogen-Doped PtRu/Carbon Anode Catalyst on the Durability of a Direct Methanol Fuel Cell
Abstract not provided
Engineering topics
Publications and source records attributed to O'Hayre, R P.
Abstract not provided
Metal-Insulator-Metal (MIM) devices are crucial components for applications ranging from optical rectennas for harvesting sunlight to infrared detectors. To date, the relationship between materials properties and device performance in MIM devices is not fully understood, partly due to the difficulty in making and reproducing reliable devices. One configuration that is popular due to itssimplicity and ease of fabrication is the point-contact diode where a metal tip serves as one of the metals in the MIM device. The intrinsic advantage of the point-contact configuration is that it is possible to achieve very small contact areas for the device thereby allowing very high-frequency operation. In this study, precise control over the contact area and penetration depth of anelectrically conductive tip into a metal/insulator combination is achieved using a nanoindenter with in-situ electrical contact resistance measurement capabilities. A diamond probe tip, doped (degeneratively) with boron for conductivity, serves as the point contact and second 'metal' (b-Diamond) of the MIM diode. The base layer consists of Nb/Nb2O5 thin films on Si substrates and serves as thefirst metal /insulator combination of the MIM structure. The current-voltage response of the diodes is measured under a range of conditions to assess the validity and repeatability of the technique. Additionally, we compare the results of this technique to those acquired using a bent-wire approach and find that Nb/Nb2O5/b-Diamond MIM devices show an excellent asymmetry (60-300) and nonlinearityvalues (~6-9). This technique shows great promise for screening metal-insulator combinations for performance without the uncertainty that stems from a typical bent-wire point-contact.
In{sub 2}Se{sub 3}, Cu{sub 2}Se, and CuInSe{sub 2} thin films have been successfully fabricated using novel metal organic decomposition (MOD) precursors and atmospheric pressure-based deposition and processing. The phase evolution of the binary (In-Se and Cu-Se) and ternary (Cu-In-Se) MOD precursor films was examined during processing to evaluate the nature of the phase and composition changes. The In-Se binary precursor exhibits two specific phase regimes: (i) a cubic-InxSey phase at processing temperatures between 300 and 400 C and (ii) the {gamma}-In{sub 2}Se{sub 3} phase for films annealed above 450 C. Both phases exhibit a composition of 40 at.% indium and 60 at.% selenium. The binary Cu-Se precursor films show more diverse phase behavior, and within a narrow temperature processing range a number of Cu-Se phases, including CuSe{sub 2}, CuSe, and Cu{sub 2}Se, can be produced and stabilized. The ternary Cu-In-Se precursor can be used to produce relatively dense CuInSe{sub 2} films at temperatures between 300 and 500 C. Layering the binary precursors together has provided an approach to producing CuInSe{sub 2} thin films; however, the morphology of the layered binary structure exhibits a significant degree of porosity. An alternative method of layering was explored where the Cu-Se binary was layered on top of an existing indium-gallium-selenide layer and processed. This method produced highly dense and large-grained (>3 {micro}m) CuInSe{sub 2} thin films. This has significant potential as a manufacturable route to CIGS-based solar cells.
We have employed both combinatorial composition spread and conventional single composition approaches to determine the relative roles of metals and oxygen stoichiometries on the opto-electronic properties of amorphous In-Zn-O (a-IZO) thin film transparent conductors. Two major results were found. First, that the optimization of conductivity in a-IZO is a coupled process with the best metals composition depending upon the oxygen content of the sputter gas. Second, that the electron mobility as a function of carrier concentration is given by a common curve for all a-IZO films independent of the metals composition.