Engineering topics

Obrien, T. K.

Publications and source records attributed to Obrien, T. K..

26 records · Page 2

NASA NTRS1984

Interlaminar fracture of composites

Fracture mechanics has been found to be a useful tool for understanding composite delamination. Analyses for calculating strain energy release rates associated with delamination growth have been developed. These analyses successfully characterized delamination onset and growth for particular sources of delamination. Low velocity impact has been found to be the most severe source of composite delamination. A variety of test methods for measuring interlaminar fracture toughness are being developed to identify new composite materials with enhanced delamination resistance.

Obrien, T. K.↗

NASA NTRS1984

Analysis of local delaminations and their influence on composite laminate behavior

An equation was derived for the strain energy release rate, G, associated with local delamination growth from a matrix ply crack. The critical GC for edge delamination onset in 25/902s graphite epoxy laminates was measured and used in this equation to predict local delamination onset strains in 25/90ns, n = 4, 6, 8 laminates. A simple technique for predicting strain concentrations in the primary load bearing plies near local delaminations was developed. These strain concentrations were responsible for reduced laminate nominal failure strains in laminates containing local delaminations. The influence of edge delamination and matrix crack tip delamination on laminate stiffness and strength was compared.

Obrien, T. K.↗

NASA NTRS1983

Mixed-mode strain-energy-release rate effects on edge delamination of composites

Unnotched graphite/epoxy laminates, designed to delaminate at the edges under static and cyclic tensile loads, were tested and analyzed. The specimen stacking sequences were chosen so that the total strain-energy-release rate, G, for edge delamination was identical for all three layups. However, each layup had different percentages of crack-opening and shear-mode strain-energy-release rates, G sub 1 and G sub 2, respectively. Results with composites made from T300 graphite fibers and 5208 epoxy, a brittle resin, indicated that only G sub 1 contributed to delamination onset under static loading. However, results with composites made from C6000 fibers and H205 epoxy, a tougher resin, indicated that the total F governed the onset of edge delaminations under cyclic loads. In addition, for both materials, the threshold level of G for delamination onset in fatigue was significantly less than the critical G sub c measured in static tests. Futhermore, although the C6000/H205 material had a much higher static G sub c than T300/5208, its fatigue resistance was only slightly better. A series of mixed-mode tests, like the ones in this study, may be needed to evaluate toughened-resin composites developed for highly strained composite structures subjected to cyclic loads.

Obrien, T. K.↗

NASA NTRS1983

Interlaminar fracture toughness of composites. II - Refinement of the edge delamination test and application to thermoplastics

The mixed mode interlaminar fracture toughness, G(c), is obtained for the two thermoplastic matrices UDEL P1700 polysulfone and ULTEM polyetherimide by means of edge delamination tensile (EDT) tests on unnotched, eleven-ply graphite fiber reinforced composite specimens. A novel method is used to obtain the stiffness parameter employed in the closed form equation for the calculation of G(c), decreasing the number of stiffness measurements required and simplifying the calculations. The G(Ic) values from double cantilever beam (DCB) measurements on composites of the two thermoplastics were similar to each other, but slightly higher than the G(c) data obtained by EDT. Interfacial resin/fiber failures predominated in both the EDT and DCB tests.

Johnston, N. J.↗

NASA NTRS1983

Determination of interlaminar fracture toughness and fracture mode dependence of composites using the edge delamination test

Edge delamination testing has been conducted in order to determine the mixed mode interlaminar fracture toughness of unnotched (+, -35/0/90)s and (0/+, -35/90)s laminates with graphite fibers and epoxy matrices, with or without elastomer additives. Although the two stacking sequences were chosen so that the total strain energy release rates were equal, the percentages of crack opening and shear mode energy release rates were found to vary widely between the layups. Plots of interlaminar fracture toughness as a function of crack opening energy release rate percentage have been drawn to generate delamination failure criteria which reflect the observed fracture mode dependence.

Obrien, T. K.↗

NASA NTRS1982

A simple test for the interlaminar fracture toughness of composites

A simple test method for the measurement of delamination resistance is assessed through its application to 11-ply graphite-epoxy laminates whose matrices employ the F185 and 205 resins. The F185 resin has the same base epoxy as the 205, to which liquid and solid elastomers have been added. The critical value of the mixed mode energy release rate, calculated from a closed form equation employing nominal strain measurements from the onset of edge delamination, show that addition of the elastomers to the base epoxy increases interlaminar fracture toughness. Comparison of these results with those of width-tapered double cantilever beam (WTDCB) test data for the two materials shows a similar strain energy release rate, establishing the accuracy of the novel method. Both tests are found to be needed, however, for the quantitative characterization of interlaminar fracture toughness.

Obrien, T. K.↗

NASA NTRS1981

Characterization of delamination onset and growth in a composite laminate

The onset and growth of delaminations in unnotched (+ or - 30/+ or - 30/90/90 bar) sub S graphite epoxy laminates is described quantitatively. These laminates, designed to delaminate at the edges under tensile loads, were tested and analyzed. Delamination growth and stiffness loss were monitored nondestructively. Laminate stiffness decreased linearly with delamination size. The strain energy release rate, G, associated with delamination growth, was calculated from two analyses. A critical G for delamination onset was determined, and then was used to predict the onset of delaminations in (+45 sub n/-45 sub n/o sub n/90 sub n) sub s (n=1,2,3) laminates. A delamination resistance curve (R curve) was developed to characterize the observed stable delamination growth under quasi static loading. A power law correlation between G and delamination growth rates in fatigue was established.

Obrien, T. K.↗

NASA NTRS1980

Development of a laminate fatigue analysis

A fatigue analysis technique developed to predict damage growth in notched laminates is described. Features of the analysis include: criteria to relate matrix failure to cyclic stresses in and between plies; correlation of delamination growth with strain-release rate; and in-plane shear modulus change is related to cyclic shear stresses. A simplified finite element model is used to determine stresses in laminates that contain matrix damage. Failure criteria are integrated with the finite element model to form the fatigue analysis.

Roderick, G. L.↗