Engineering topics

Ohlhorst, Craig W.

Publications and source records attributed to Ohlhorst, Craig W..

10 records

NASA NTRS2007

Emissivity Results on High Temperature Coatings for Refractory Composite Materials

The directional emissivity of various refractory composite materials considered for application for reentry and hypersonic vehicles was investigated. The directional emissivity was measured at elevated temperatures of up to 3400 F using a directional spectral radiometric technique during arc-jet test runs. A laboratory-based relative total radiance method was also used to measure total normal emissivity of some of the refractory composite materials. The data from the two techniques are compared. The paper will also compare the historical database of Reinforced Carbon-Carbon emissivity measurements with emissivity values generated recently on the material using the two techniques described in the paper.

Ohlhorst, Craig W.↗

NASA NTRS2006

Lightweight Ablative and Ceramic Thermal Protection System Materials for NASA Exploration Systems Vehicles

As a collaborative effort among NASA Centers, the "Lightweight Nonmetallic Thermal Protection Materials Technology" Project was set up to assist mission/vehicle design trade studies, to support risk reduction in thermal protection system (TPS) material selections, to facilitate vehicle mass optimization, and to aid development of human-rated TPS qualification and certification plans. Missions performing aerocapture, aerobraking, or direct aeroentry rely on advanced heatshields that allow reductions in spacecraft mass by minimizing propellant requirements. Information will be presented on candidate materials for such reentry approaches and on screening tests conducted (material property and space environmental effects tests) to evaluate viable candidates. Seventeen materials, in three classes (ablatives, tiles, and ceramic matrix composites), were studied. In additional to physical, mechanical, and thermal property tests, high heat flux laser tests and simulated-reentry oxidation tests were performed. Space environmental effects testing, which included exposures to electrons, atomic oxygen, and hypervelocity impacts, was also conducted.

Valentine, Peter G.↗

NASA NTRS2005

Lightweight Nonmetallic Thermal Protection Materials Technology

To fulfill President George W. Bush's "Vision for Space Exploration" (2004) - successful human and robotic missions to and from other solar system bodies in order to explore their atmospheres and surfaces - the National Aeronautics and Space Administration (NASA) must reduce the trip time, cost, and vehicle weight so that the payload and scientific experiments' capabilities can be maximized. The new project described in this paper will generate thermal protection system (TPS) product that will enable greater fidelity in mission/vehicle design trade studies, support risk reduction for material selections, assist in the optimization of vehicle weights, and provide materials and processes templates for use in the development of human-rated TPS qualification and certification plans.

Valentine, Peter G.↗

NASA NTRS2005

Thermal Protection Materials Technology for NASA's Exploration Systems Mission Directorate

To fulfill the President s Vision for Space Exploration - successful human and robotic missions between the Earth and other solar system bodies in order to explore their atmospheres and surfaces - NASA must reduce trip time, cost, and vehicle weight so that payload and scientific experiment capabilities are maximized. As a collaboration among NASA Centers, this project will generate products that will enable greater fidelity in mission/vehicle design trade studies, support risk reduction for material selections, assist in optimization of vehicle weights, and provide the material and process templates for development of human-rated qualification and certification Thermal Protection System (TPS) plans. Missions performing aerocapture, aerobraking, or direct aeroentry rely on technologies that reduce vehicle weight by minimizing the need for propellant. These missions use the destination planet s atmosphere to slow the spacecraft. Such mission profiles induce heating environments on the spacecraft that demand thermal protection heatshields. This program offers NASA essential advanced thermal management technologies needed to develop new lightweight nonmetallic TPS materials for critical thermal protection heatshields for future spacecraft. Discussion of this new program (a December 2004 new start) will include both initial progress made and a presentation of the work to be preformed over the four-year life of the program. Additionally, the relevant missions and environments expected for Exploration Systems vehicles will be presented, along with discussion of the candidate materials to be considered and of the types of testing to be performed (material property tests, space environmental effects tests, and Earth and Mars gases arc jet tests).

Valentine, Peter G.↗

NASA NTRS2005

Development of X-43A Mach 10 Leading Edges

The nose leading edge of the Hyper-X Mach 10 vehicle was orginally anticipated to reach temperatures near 4000 F at the leading-edge stagnation line. A SiC coated carbon/carbon (C/C) leading-edge material will not survive that extreme temperature for even a short duration single flight. To identify a suitable leading edge for the Mach 10 vehicle, arc-jet testing was performed on thirteen leading-edge segments fabricated from different material systems to evaluate their performance in a simulated flight environment. Hf, Zr, Si, and Ir based materials, in most cases as a coating on C/C, were included in the evaluation. Afterwards, MER, Tucson, AZ was selected as the supplier of the flight vehicle leading edges. The nose and the vertical and horizontal tail leading edges were fabricated out of a 3:1 biased high thermal conductivity C/C. The leading edges were coated with a three layer coating comprised of a SiC conversion of the top surface of the C/C, followed by a chemical vapor deposited layer of SiC, followed by a thin chemical vapor deposited layer of HfC. This paper will describe the fabrication of the Mach 10 C/C leading edges and the testing performed to validate performance.

Ohlhorst, Craig W.↗

NASA NTRS1997

Thermal Conductivity Database of Various Structural Carbon-Carbon Composite Materials

Advanced thermal protection materials envisioned for use on future hypersonic vehicles will likely be subjected to temperatures in excess of 1811 K (2800 F) and, therefore, will require the rapid conduction of heat away from the stagnation regions of wing leading edges, the nose cap area, and from engine inlet and exhaust areas. Carbon-carbon composite materials are candidates for use in advanced thermal protection systems. For design purposes, high temperature thermophysical property data are required, but a search of the literature found little thermal conductivity data for carbon-carbon materials above 1255 K (1800 F). Because a need was recognized for in-plane and through-the-thickness thermal conductivity data for carbon-carbon composite materials over a wide temperature range, Langley Research Center (LaRC) embarked on an effort to compile a consistent set of thermal conductivity values from room temperature to 1922 K (3000 F) for carbon-carbon composite materials on hand at LaRC for which the precursor materials and thermal processing history were known. This report documents the thermal conductivity data generated for these materials. In-plane thermal conductivity values range from 10 to 233 W/m-K, whereas through-the-thickness values range from 2 to 21 W/m-K.

Ohlhorst, Craig W.↗

NASA NTRS1992

Current research in oxidation-resistant carbon-carbon composites at NASA. Langley Research Center

The significant potential of carbon-carbon composites for high-temperature structural applications is well established. For hypersonic vehicle applications, desirable properties include low density, high specific strength and stiffness, low coefficients of thermal expansion, and retention of mechanical properties above 3000 F. A significant problem associated with carbon materials, however, is that they oxidize rapidly in air at temperatures above about 800 F, and therefore must be protected from oxidation. Successful development of effective methods of oxidation protection is key to the eventual utilization of carbon-carbon composites on hypersonic vehicles such as NASP. In this presentation, the basic elements of an oxidation-protection system are described. Results from oxidation-performance evaluations of state-of-the-art ACC-4 type material in simulated airframe vehicle environments (temperature, pressure, and time) conducted at NASA Langley are also presented. NASA Langley has an active research effort to improve the oxidation resistance of carbon-carbon materials for airframe structural and vehicle thermal protection applications. Conversion coating and sealant development research is highlighted.

Ohlhorst, Craig W.↗

NASA NTRS1990

NASA Langley Research Center National Aero-Space Plane Mission simulation profile sets

To provide information on the potential for long life service of oxidation resistant carbon-carbon (ORCC) materials in the National Aero-Space Plane (NASP) airframe environment, NASP ascent, entry, and cruise trajectories were analytically flown. Temperature and pressure profiles were generated for 20 vehicle locations. Orbital (ascent and entry) and cruise profile sets from four locations are presented along with the humidity exposure and testing sequences that are being used to evaluate ORCC materials. The four profiles show peak temperatures during the ascent leg of an orbital mission of 2800, 2500, 2000, and 1700 F. These profiles bracket conditions where carbon-carbon might be used on the NASP vehicle.

Ohlhorst, Craig W.↗

NASA NTRS1989

Investigation of test methods for measuring compressive strength and modulus of two-dimensional carbon-carbon composites

An experimental evaluation has been conducted to ascertain the the usefulness of two techniques for measuring in-plane compressive failure strength and modulus in coated and uncoated carbon-carbon composites. The techniques involved testing specimens with potted ends as well as testing them in a novel clamping fixture; specimen shape, length, gage width, and thickness were the test parameters investigated for both coated and uncoated 0/90 deg and +/-45 deg laminates. It is found that specimen shape does not have a significant effect on the measured compressive properties. The potting of specimen ends results in slightly higher measured compressive strengths than those obtained with the new clamping fixture. Comparable modulus values are obtained by both techniques.

Ohlhorst, Craig W.↗

NASA NTRS1988

Response of carbon-carbon composites to challenging environments

This paper presents results from material performance evaluations of oxidation-resistant carbon-carbon composites intended for multiuse aerospace applications, which cover the effects of the following environmental parameters: the oxidizing nature of the environments (including both high and low oxygen partial pressures), high temperatures, moisture, cyclic temperature service, and foreign-object impact. Results are presented for the carbon-carbon material currently in use as the thermal-protection-system material on Space Shuttle, as well as for newer and more advanced structural forms of carbon-carbon composites.

Maahs, Howard G.↗