Search NASA⌕ Search

Engineering topics

Okajima, Yuka

Publications and source records attributed to Okajima, Yuka.

Pulmonary lobe segmentation based on ridge surface sampling and shape model fitting

Purpose: Performing lobe-based quantitative analysis of the lung in computed tomography (CT) scans can assist in efforts to better characterize complex diseases such as chronic obstructive pulmonary disease (COPD). While airways and vessels can help to indicate the location of lobe boundaries, segmentations of these structures are not always available, so methods to define the lobes in the absence of these structures are desirable. Methods: The authors present a fully automatic lung lobe segmentation algorithm that is effective in volumetric inspiratory and expiratory computed tomography (CT) datasets. The authors rely on ridge surface image features indicating fissure locations and a novel approach to modeling shape variation in the surfaces defining the lobe boundaries. The authors employ a particle system that efficiently samples ridge surfaces in the image domain and provides a set of candidate fissure locations based on the Hessian matrix. Following this, lobe boundary shape models generated from principal component analysis (PCA) are fit to the particles data to discriminate between fissure and nonfissure candidates. The resulting set of particle points are used to fit thin plate spline (TPS) interpolating surfaces to form the final boundaries between the lung lobes. Results: The authors tested algorithm performance on 50 inspiratory and 50 expiratory CT scans taken from the COPDGene study. Results indicate that the authors' algorithm performs comparably to pulmonologist-generated lung lobe segmentations and can produce good results in cases with accessory fissures, incomplete fissures, advanced emphysema, and low dose acquisition protocols. Dice scores indicate that only 29 out of 500 (5.85%) lobes showed Dice scores lower than 0.9. Two different approaches for evaluating lobe boundary surface discrepancies were applied and indicate that algorithm boundary identification is most accurate in the vicinity of fissures detectable on CT. Conclusions: The proposed algorithm is effective for lung lobe segmentation in absence of auxiliary structures such as vessels and airways. The most challenging cases are those with mostly incomplete, absent, or near-absent fissures and in cases with poorly revealed fissures due to high image noise. However, the authors observe good performance even in the majority of these cases.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Magnetic and dielectric study of R{sub 0.5}Sr{sub 0.5}MnO{sub 3} (R = Gd, Tb and Dy)

Magnetic and dielectric properties of perovskite manganites R{sub 0.5}Sr{sub 0.5}MnO{sub 3} (R = Gd, Tb and Dy) have been investigated. DC and AC magnetic measurements showed short-range glassy magnetic ordering at T{sub g} {approx} 40 K. Such ordering was observed by neutron diffraction and is ascribable to the size mismatch of R{sup 3+} and Sr{sup 3+} settled randomly at the same crystallographic site. Dielectric constants for each material were {approx}1000-10,000 between {approx}50 and {approx}300 K and showed broad maximums above T{sub g}. Dielectric dispersion showed poor coherency of the motion of polar regions, plausibly because of the size-mismatch effect; both the magnetic and dielectric properties of this system are governed by the randomness at the R/Sr site. The tan {delta} and EXAFS data suggest that the dielectric response is rooted in a transfer of the Mn-3d electrons.

36 MATERIALS SCIENCE↗

Magnetic and dielectric properties of YbFe{sub 2-x}Mn{sub x}O{sub 4} (0<=x<=1)

We have investigated the magnetic and dielectric properties of YbFe{sub 2-x}Mn{sub x}O{sub 4} (0<=x<=1), which is an Fe-site-substituted system of new multiferroic oxides RFe{sub 2}O{sub 4} (R=Y, Ho-Lu). X-ray diffraction measurements show that a solid solution is formed between YbFe{sub 2}O{sub 4} (x=0) and YbFeMnO{sub 4} (x=1) for 0<=x<=1, whereas only compounds with x=1 (i.e., RM{sub 1}M{sub 2}O{sub 4}; M{sub 1} and M{sub 2}=trivalent and divalent cations, respectively) have been known for the Fe-site substitution in RFe{sub 2}O{sub 4}. The valence of the Mn ion is determined to be {approx}2+, consistently with the suppression of low-temperature magnetization by the Mn substitution. The magnetic transition temperature (T{sub N}) and the dielectric constant (epsilon') decrease monotonically with increasing x. This result plausibly confirms that the magnetic and dielectric properties in oxides isostructural with RFe{sub 2}O{sub 4} are governed by the electron transfer between Fe-site ions, unlike ordinary ferroelectrics and dielectrics, in which the ionic displacement plays a key role. The possibility for application is briefly discussed as well. - Graphical abstract: Dielectric constant (epsilon') and magnetic transition temperature (T{sub N}) of YbFe{sub 2-x}Mn{sub x}O{sub 4} (0<=x<=1), which is a solid-solution system of new multiferroic oxides RFe{sub 2}O{sub 4} (R=Y, Ho-Lu).

36 MATERIALS SCIENCE↗