Search NASA⌕ Search

Engineering topics

Olsen, Daniel

Publications and source records attributed to Olsen, Daniel.

36 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2019

Ignition, Flame Propagation, and End-Gas Autoignition Studies of Natural Gas/EGR Blends in a Rapid Compression Machine

The development of high efficiency, spark ignited natural gas engines is currently limited by engine knock at high power density (at high compression ratio and/or elevated boost pressures) and misfire (at lean conditions and/or high exhaust gas recirculation levels). The knock and misfire limits are further confounded by the wide variety in fuel reactivity observed in “pipeline quality” natural gas. In this study, a rapid compression machine (RCM) was used to characterize the effects of variation in natural gas fuel reactivity and exhaust gas recirculation (EGR) on homogeneous ignition delay, flame propagation rate and end-gas autoignition (EGAI) propensity for stoichiometric natural gas/oxidizer/EGR blends. Pipeline quality natural gas with variable reactivity (68 < Methane Number < 95) was simulated using mixtures of methane, ethane, and propane. EGR was simulated with mixtures of Ar, CO2, CO, and NO. EGR substitution rates were varied from 0 to 30 mass percent. Ignition delay period under homogeneous autoignition conditions was measured at compressed pressures of 24.0 to 33.1 bar and compressed temperatures of 667 to 980 K. Flame propagation rate and EGAI propensity was measured at spark-ignition pressures of 29.9 to 32.9 bar and temperatures of 721 to 782 K.

Ignition Delay, Flame Propagation Rate, Rapid Comp↗
DOE OSTI2019

The Effect of EGR on Knock Suppression, Efficiency, and Emissions in a Stoichiometric, Spark Ignited, Natural Gas Engine

Exhaust gas recirculation (EGR) is widely employed on internal combustion engines for NOx reduction and knock suppression. In this study a comprehensive analysis was performed to determine the effect of EGR on efficiency, emissions, and knock suppression of stoichiometric, spark ignited, natural gas engines. Tests were conducted using a single cylinder, variable compression ratio, cooperative fuel research (CFR) engine at 900 RPM, engine load of 800 kPa indicated mean effective pressure (IMEP), and stoichiometric conditions. The tests were performed using a custom EGR system capable of providing a range of EGR displacement rates from 0% to 40% of the intake charge at engine power levels between 1.5 and 3.5 kW. The experimental measurements included the variance of EGR rate, compression ratio, boost pressure, and location of 50% mass fraction burned (CA50). CA50 was controlled with ignition timing using a Woodward Large Engine Control Module. The use of EGR was found to expand the knock limit, while reducing NOx emissions and increasing engine efficiency as much as 4.5% through increased compression ratio and power density. The highest EGR rate that demonstrated beneficial gains on the CFR engine was 23%; the optimal EGR rate was found to be 19%.

Cooperative Fuel Research Engine, Exhaust Gas Reci↗
DOE OSTI2019

The Effect of EGR on Knock Suppression, Efficiency, and Emissions in a Stoichiometric

Exhaust gas recirculation (EGR) is widely employed on internal combustion engines for NOx reduction and knock suppression. In this study a comprehensive analysis was performed to determine the effect of EGR on efficiency, emissions, and knock suppression of stoichiometric, spark ignited, natural gas engines. Tests were conducted using a single cylinder, variable compression ratio, cooperative fuel research (CFR) engine at 900 RPM, engine load of 800 kPa indicated mean effective pressure (IMEP), and stoichiometric conditions. The tests were performed using a custom EGR system capable of providing a range of EGR displacement rates from 0% to 40% of the intake charge at engine power levels between 1.5 and 3.5 kW. The experimental measurements included the variance of EGR rate, compression ratio, boost pressure, and location of 50% mass fraction burned (CA50). CA50 was controlled with ignition timing using a Woodward Large Engine Control Module. The use of EGR was found to expand the knock limit, while reducing NOx emissions and increasing engine efficiency as much as 4.5% through increased compression ratio and power density. The highest EGR rate that demonstrated beneficial gains on the CFR engine was 23%; the optimal EGR rate was found to be 19%.

Bayliff, Scott↗
DOE OSTI2019

3-D Modeling off the CFR Engine for the Investigation of Knock on Natural Gas

Engine knock and misfire are barriers to pathways leading to high-efficiency Natural Gas (NG) engines. The general tendency to knock is highly dependent on engine operating conditions and the fuel reactivity. The problem is further complicated by low emissions limits and the wide range of chemical reactivity in pipeline quality NG (65< MN<95). In order to realize diesel-like efficiencies, spark-ignited NG engines must be designed to operate at high BMEP near knock limits over a wide range of fuel reactivity. This requires a deep understanding regarding combustion-engine interactions important in flame propagation and end-gas autoignition. The present work highlights a three-dimensional computational fluid dynamics (CFD) model of the Cooperative Fuel Research (CFR) engine to investigate knock behavior with NG. The CFR engine model is used to investigate fuel-engine interactions that lead to knock with NG, including effects of fuel reactivity, engine operating parameters, and exhaust gas recirculation (EGR). Cylinder wall, piston, valves, and port surface temperatures are estimated with a 1-D Three-Pressure Analysis (TPA) model. Model validation was performed by comparing model predictions with experimental data taken with a CFR engine over varying compression ratio, CA50, EGR fraction and BMEP.

Bestel, Diego↗
DOE OSTI2019

Effect of Fuel Reactivity and End- Gas Temperature on Autoignition and Flame Propagation Rate in Primary Reference Fuel Mixtures at Elevated Temperature and Pressure

Knock in spark-ignited (SI) engines is initiated by autoignition in the unburned gases upstream of spark-ignited, propagating, turbulent premixed flames. In this study, knock propensity of SI fuels was quantified via observations of end-gas autoignition (EGAI) in unburned gases upstream of laser-ignited, premixed flames at elevated pressures and temperatures in a rapid compression machine. Stoichiometric primary reference fuel (n-heptane/isooctane) blends of varying reactivity were ignited using an Nd:YAG laser over a range of compressed temperatures and pressures, all in excess of 691 K and 18.8 bar. High-speed pressure measurements and schlieren images indicated the presence of EGAI in the unburned gases upstream of spherical, outwardly propagating flames. The fraction of the total heat release attributed to EGAI was found to vary with fuel reactivity and the time-integrated temperature of the end-gas prior to ignition. Flame propagation rates, measured using schlieren imaging, did not vary strongly with fuel reactivity but were affected by turbulence caused by variation in piston timing. Under conditions of low turbulence, measured flame propagation rates agreed with one-dimensional premixed laminar flame speed computations performed at the same conditions.

Zdanowicz, Andrew↗
DOE OSTI2019

Ignition, Flame Progation, and End-Gas Autoignition Studies of Natural Gas/ EGR Blends in a Rapid Compression Machine

The development of high efficiency, spark ignited natural gas engines is currently limited by engine knock at high power density (at high compression ratio and/or elevated boost pressures) and misfire (at lean conditions and/or high exhaust gas recirculation levels). The knock and misfire limits are further confounded by the wide variety in fuel reactivity observed in “pipeline quality” natural gas. In this study, a rapid compression machine (RCM) was used to characterize the effects of variation in natural gas fuel reactivity and exhaust gas recirculation (EGR) on homogeneous ignition delay, flame propagation rate and end-gas autoignition (EGAI) propensity for stoichiometric natural gas/oxidizer/EGR blends. Pipeline quality natural gas with variable reactivity (68 < Methane Number < 95) was simulated using mixtures of methane, ethane, and propane. EGR was simulated with mixtures of Ar, CO2, CO, and NO. EGR substitution rates were varied from 0 to 30 mass percent. Ignition delay period under homogeneous autoignition conditions was measured at compressed pressures of 24.0 to 33.1 bar and compressed temperatures of 667 to 980 K. Flame propagation rate and EGAI propensity was measured at spark-ignition pressures of 29.9 to 32.9 bar and temperatures of 721 to 782 K.

Mohr, Jeffrey↗
DOE OSTI2019

3-D Modeling of the CFR Engine for the Investigation of Knock on Natural Gas

Abstract: Engine knock and misfire are barriers to pathways leading to higher efficiency natural gas (NG) engines, where the general tendency to knock is highly dependent on engine operating conditions and the fuel reactivity. The problem is further complicated by low emissions limits and the wide range of chemical reactivity in pipeline quality NG, making the understanding of fuel- engine interactions essential to achieving high efficiencies in spark-ignited NG engines. The present work highlights a three-dimensional computational fluid dynamics (CFD) model of the Cooperative Fuel Research (CFR) engine to investigate knock behavior when running on NG. Using a Converge CFD model of the CFR engine fuel-engine interactions that lead to knock with NG, including effects of fuel reactivity, engine operating parameters, and exhaust gas recirculation, are being investigated. A GT-Power model is used to estimate appropriate initial conditions in the Converge CFD model, including cylinder wall, piston, valves, and port surface temperatures as well as residual gas fraction. In order to validate the model, in-cylinder pressure data taken with a CFR engine is compared to model predictions while varying compression ratio, CA50, and BMEP.

CFR Engine, Converge CFD, knock, Natural Gas↗
DOE OSTI2019

3-D Modeling of the CFR Engine for the Investigation of Knock on Natural Gas

Engine knock and misfire are barriers to pathways leading to higher efficiency natural gas (NG) engines, where the general tendency to knock is highly dependent on engine operating conditions and the fuel reactivity. The problem is further complicated by low emissions limits and the wide range of chemical reactivity in pipeline quality NG, making the understanding of fuel-engine interactions essential to achieving high efficiencies in spark-ignited NG engines. The present work highlights a three-dimensional computational fluid dynamics (CFD) model of the Cooperative Fuel Research (CFR) engine to investigate knock behavior when running on NG. Using a Converge CFD model of the CFR engine fuel-engine interactions that lead to knock with NG, including effects of fuel reactivity, engine operating parameters, and exhaust gas recirculation, are being investigated. A GT-Power model is used to estimate appropriate initial conditions in the Converge CFD model, including cylinder wall, piston, valves, and port surface temperatures as well as residual gas fraction. In order to validate the model, in-cylinder pressure data taken with a CFR engine is compared to model predictions while varying compression ratio, CA50, and BMEP.

Bestel, Diego↗
DOE OSTI2016

Intravascular Papillary Endothelial Hyperplasia (Masson’s Tumor) of the Radial Artery: A Case Report

Intravascular papillary endothelial hyperplasia (IPEH), often referred to as Masson’s tumor, is a benign non-neoplastic vascular lesion of the skin and subcutaneous tissues. Although it is rare, knowledge of the existence of IPEH is important as it can mimic other benign and malignant tumors, most notably angiosarcoma. IPEH remains an incompletely understood entity; however, most consider it to be the result of reactive endothelial proliferation following thrombus formation within a vessel, vascular malformation, or adjacent to a vessel. In this article, we report a case of IPEH arising within an arteriovenous malformation of the radial artery and present accompanying multimodality imaging and pathology figures. We will also describe the clinical presentation, pathophysiology, histology, imaging features, and management of IPEH.

62 RADIOLOGY AND NUCLEAR MEDICINE↗
DOE OSTI2015

Refrigerated Warehouse Demand Response Strategy Guide

This guide summarizes demand response measures that can be implemented in refrigerated warehouses. In an appendix, it also addresses related energy efficiency opportunities. Reducing overall grid demand during peak periods and energy consumption has benefits for facility operators, grid operators, utility companies, and society. State wide demand response potential for the refrigerated warehouse sector in California is estimated to be over 22.1 Megawatts. Two categories of demand response strategies are described in this guide: load shifting and load shedding. Load shifting can be accomplished via pre-cooling, capacity limiting, and battery charger load management. Load shedding can be achieved by lighting reduction, demand defrost and defrost termination, infiltration reduction, and shutting down miscellaneous equipment. Estimation of the costs and benefits of demand response participation yields simple payback periods of 2-4 years. To improve demand response performance, it’s suggested to install air curtains and another form of infiltration barrier, such as a rollup door, for the passageways. Further modifications to increase efficiency of the refrigeration unit are also analyzed. A larger condenser can maintain the minimum saturated condensing temperature (SCT) for more hours of the day. Lowering the SCT reduces the compressor lift, which results in an overall increase in refrigeration system capacity and energy efficiency. Another way of saving energy in refrigerated warehouses is eliminating the use of under-floor resistance heaters. A more energy efficient alternative to resistance heaters is to utilize the heat that is being rejected from the condenser through a heat exchanger. These energy efficiency measures improve efficiency either by reducing the required electric energy input for the refrigeration system, by helping to curtail the refrigeration load on the system, or by reducing both the load and required energy input.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2015

Opportunities for Automated Demand Response in California Agricultural Irrigation

Pumping water for agricultural irrigation represents a significant share of California’s annual electricity use and peak demand. It also represents a large source of potential flexibility, as farms possess a form of storage in their wetted soil. By carefully modifying their irrigation schedules, growers can participate in demand response without adverse effects on their crops. This report describes the potential for participation in demand response and automated demand response by agricultural irrigators in California, as well as barriers to widespread participation. The report first describes the magnitude, timing, location, purpose, and manner of energy use in California. Typical on-­farm controls are discussed, as well as common impediments to participation in demand response and automated demand response programs. Case studies of demand response programs in California and across the country are reviewed, and their results along with overall California demand estimates are used to estimate statewide demand response potential. Finally, recommendations are made for future research that can enhance the understanding of demand response potential in this industry.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2015

Characterization of demand response in the commercial, industrial, and residential sectors in the United States

The goal of our study is to provide an overview of demand response (DR) technologies, including standards and end uses, in the United States and describe resource characteristics and the attributes of 14 specific DR resources in the U.S. commercial, residential, and industrial sectors. The attributes reviewed for the end uses being considered are response frequency, response time, the need for and impacts of energy pre- or recharge, the cost of enabling a resource to respond to a load-curtailment signal, and the magnitude of load curtailment in a given resource. We also describe controls and communications technologies that can enable end uses to participate in DR programs. The characterization was initially developed as a foundational work to quantify hourly availability of DR resources from the selected end uses followed by a multi-laboratory effort that quantified DR's value within the Western Interconnection.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2014

Demand Response Availability Profiles for California in the Year 2020

Demand response (DR) is being considered as a valuable resource for keeping the electrical grid stable and efficient, and deferring upgrades to generation, transmission, and distribution systems. However, simulations to determine how much infrastructure upgrades can be deferred are necessary in order to plan optimally. Production cost modeling is a technique, which simulates the dispatch of generators to meet demand and reserves in each hour of the year, at minimal cost. By integrating demand response resources into a production cost model (PCM), their value to the grid can be estimated and used to inform operations and infrastructure planning. DR availability profiles and constraints for 13 end-uses in California for the year 2020 were developed by Lawrence Berkeley National Laboratory (LBNL), and integrated into a production cost model by Lawrence Livermore National Laboratory (LLNL), for the California Energy Commission’s Value of Energy Storage and Demand Response for Renewable Integration in California Study. This report summarizes the process for developing the DR availability profiles for California, and their aggregate capabilities. While LBNL provided potential DR hourly profiles for regulation product in the ancillary services market and five-minute load following product in the energy market for LLNL’s study, additional results in contingency reserves and an assumed flexible product are also defined. These additional products are included in the analysis for managing high ramps associated with renewable generation and capacity products and they are also presented in this report.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2014

Taxonomy for Modeling Demand Response Resources

Demand response resources are an important component of modern grid management strategies. Accurate characterizations of DR resources are needed to develop systems of optimally managed grid operations and to plan future investments in generation, transmission, and distribution. The DOE Demand Response and Energy Storage Integration Study (DRESIS) project researched the degree to which demand response (DR) and energy storage can provide grid flexibility and stability in the Western Interconnection. In this work, DR resources were integrated with traditional generators in grid forecasting tools, specifically a production cost model of the Western Interconnection. As part of this study, LBNL developed a modeling framework for characterizing resource availability and response attributes of DR resources consistent with the governing architecture of the simulation modeling platform. In this report, we identify and describe the following response attributes required to accurately characterize DR resources: allowable response frequency, maximum response duration, minimum time needed to achieve load changes, necessary pre- or re-charging of integrated energy storage, costs of enablement, magnitude of controlled resources, and alignment of availability. We describe a framework for modeling these response attributes, and apply this framework to characterize 13 DR resources including residential, commercial, and industrial end-uses. We group these end-uses into three broad categories based on their response capabilities, and define a taxonomy for classifying DR resources within these categories. The three categories of resources exhibit different capabilities and differ in value to the grid. Results from the production cost model of the Western Interconnection illustrate that minor differences in resource attributes can have significant impact on grid utilization of DR resources. The implications of these findings will be explored in future DR valuation studies.

Olsen, Daniel↗
DOE OSTI2014

Agricultural Irrigation Demand Response Estimation Tool

This program is used to model the energy demand of agricultural irrigation pumps, used to maintain soil moisture levels in irrigated fields. This modeling is accomplished using historical data from evapotranspirationmeasuring weather stations (from the California Irrigation Management Information System) as well as irrigation system characteristics for the field(s) to be modeled. The modelled energy demand is used to estimate the achievable demand response (DR) potential of the field(s), for use in assessing the value of the DR for the utility company. The program can accept input data with varying degrees of rigor, and estimate the uncertainty of the output accordingly.

Olsen, Daniel↗
DOE OSTI2013

Opportunities for Demand Response in California Agricultural Irrigation: A Scoping Study

California agricultural irrigation consumes more than ten billion kilowatt hours of electricity annually and has significant potential for contributing to a reduction of stress on the grid through demand response, permanent load shifting, and energy efficiency measures. To understand this potential, a scoping study was initiated for the purpose of determining the associated opportunities, potential, and adoption challenges in California agricultural irrigation. The primary research for this study was conducted in two ways. First, data was gathered and parsed from published sources that shed light on where the best opportunities for load shifting and demand response lie within the agricultural irrigation sector. Secondly, a small limited survey was conducted as informal face-to-face interviews with several different California growers to get an idea of their ability and willingness to participate in permanent load shifting and/or demand response programs. Analysis of the data obtained from published sources and the survey reveal demand response and permanent load shifting opportunities by growing region, irrigation source, irrigation method, grower size, and utility coverage. The study examines some solutions for demand response and permanent load shifting in agricultural irrigation, which include adequate irrigation system capacity, automatic controls, variable frequency drives, and the contribution from energy efficiency measures. The study further examines the potential and challenges for grower acceptance of demand response and permanent load shifting in California agricultural irrigation. As part of the examination, the study considers to what extent permanent load shifting, which is already somewhat accepted within the agricultural sector, mitigates the need or benefit of demand response for agricultural irrigation. Recommendations for further study include studies on how to gain grower acceptance of demand response as well as other related studies such as conducting a more comprehensive survey of California growers.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2012

Opportunities for Automated Demand Response in Wastewater Treatment Facilities in California - Southeast Water Pollution Control Plant Case Study

This report details a study into the demand response potential of a large wastewater treatment facility in San Francisco. Previous research had identified wastewater treatment facilities as good candidates for demand response and automated demand response, and this study was conducted to investigate facility attributes that are conducive to demand response or which hinder its implementation. One years' worth of operational data were collected from the facility's control system, submetered process equipment, utility electricity demand records, and governmental weather stations. These data were analyzed to determine factors which affected facility power demand and demand response capabilities The average baseline demand at the Southeast facility was approximately 4 MW. During the rainy season (October-March) the facility treated 40% more wastewater than the dry season, but demand only increased by 4%. Submetering of the facility's lift pumps and centrifuges predicted load shifts capabilities of 154 kW and 86 kW, respectively, with large lift pump shifts in the rainy season. Analysis of demand data during maintenance events confirmed the magnitude of these possible load shifts, and indicated other areas of the facility with demand response potential. Load sheds were seen to be possible by shutting down a portion of the facility's aeration trains (average shed of 132 kW). Load shifts were seen to be possible by shifting operation of centrifuges, the gravity belt thickener, lift pumps, and external pump stations These load shifts were made possible by the storage capabilities of the facility and of the city's sewer system. Large load reductions (an average of 2,065 kW) were seen from operating the cogeneration unit, but normal practice is continuous operation, precluding its use for demand response. The study also identified potential demand response opportunities that warrant further study: modulating variable-demand aeration loads, shifting operation of sludge-processing equipment besides centrifuges, and utilizing schedulable self-generation.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗