Engineering topics

Olsen, W. A., Jr.

Publications and source records attributed to Olsen, W. A., Jr..

10 records

NASA NTRS1986

Turbulent dispersion of the icing cloud from spray nozzles used in icing tunnels

To correctly simulate flight in natural icing conditions, the turbulence in an icing simulator must be as low as possible. But some turbulence is required to mix the droplets from the spray nozzles and achieve an icing cloud of uniform liquid water content. The goal for any spray system is to obtain the widest possible spray cloud with the lowest possible turbulence in the test section of a icing tunnel. This investigation reports the measurement of turbulence and the three-dimensional spread of the cloud from a single spray nozzle. The task was to determine how the air turbulence and cloud width are affected by spray bars of quite different drag coefficients, by changes in the turbulence upstream of the spray, the droplet size, and the atomizing air. An ice accretion grid, located 6.3 m downstream of the single spray nozzle, was used to measure cloud spread. Both the spray bar and the grid were located in the constant velocity test section. Three spray bar shapes were tested: the short blunt spray bar used in the NASA Lewis Icing Research Tunnel, a thin 14.6 cm chord airfoil, and a 53 cm chord NACA 0012 airfoil. At the low airspeed (56 km/hr) the ice accretion pattern was axisymmetric and was not affected by the shape of the spray bar. At the high airspeed (169 km/hr) the spread was 30 percent smaller than at the low airspeed. For the widest cloud the spray bars should be located as far upstream in the low velocity plenum of the icing tunnel. Good comparison is obtained between the cloud spread data and predicitons from a two-dimensional cloud mixing computer code using the two equation turbulence (k epsilon g) model.

Marek, C. J.↗

NASA NTRS1983

NASA Lewis Research Center's program on icing research

NASA is again actively involved in aircraft icing research. This paper briefly describes the new research activity in ice protection systems, icing instrumentation, experimental methods, analytical modeling for the above, and in-flight research. The renewed interest in aircraft icing has come about mainly because of the new need for all-weather helicopters and general aviation aircraft. Because of increased fuel costs, tomorrow's commercial transports also will require new types of ice protection systems compatible with the more efficient high by-pass and turboprop engines. And all types of aircraft require better estimates of the aeropenalties caused by ice on unprotected surfaces.

Reinmann, J. J.↗

NASA NTRS1982

Aircraft icing research at NASA

Research activity is described for: ice protection systems, icing instrumentation, experimental methods, analytical modeling for the above, and in flight research. The renewed interest in aircraft icing has come about because of the new need for All-Weather Helicopters and General Aviation aircraft. Because of increased fuel costs, tomorrow's Commercial Transport aircraft will also require new types of ice protection systems and better estimates of the aeropenalties caused by ice on unprotected surfaces. The physics of aircraft icing is very similar to the icing that occurs on ground structures and structures at sea; all involve droplets that freeze on the surfaces because of the cold air. Therefore all icing research groups will benefit greatly by sharing their research information.

Reinmann, J. J.↗

NASA NTRS1982

NASA Lewis Research Center's Program on Icing Research

The helicopter and general aviation, light transport, and commercial transport aircraft share common icing requirements: highly effective, lightweight, low power consuming deicing systems, and detailed knowledge of the aeropenalties due to ice on aircraft surfaces. To meet current and future needs, NASA has a broadbased icing research program which covers both research and engineering applications, and is well coordinated with the FAA, DOD, universities, industry, and some foreign governments. Research activity in ice protection systems, icing instrumentation, experimental methods, analytical modeling, and in-flight research are described.

Reinmann, J. J.↗

NASA NTRS1972

Engine noise technology

The characteristics of aircraft engine noise are discussed. Data are provided to show the noise produced by the following aircraft components: (1) fan noise, (2) noise suppressing structures, (3) sonic inlets, (4) jet mixing noise due to nozzle flow, and (5) thrust reversers. Charts are developed to show the sound pressure level and the frequencies for each type of noise source. The use of laminates and composite materials to dissipate acoustic power is examined.

Luidens, R. W.↗

NASA NTRS1970