5,10-Dihydroindolo[3,2-b]indole-Based Copolymers with Alternating Donor and Acceptor Moieties for Organic Photovoltaics
Abstract not provided
Engineering topics
Publications and source records attributed to Olson, D C.
Abstract not provided
Abstract not provided
Hybrid organic/inorganic solar cells have not lived up to their potential because of poor interface properties. Interfacial molecular layers provide a way of adjusting these devices to improve their performance. We have studied a prototypical system involving poly(3-hexylthiophene) (P3HT) on planar zinc oxide (ZnO) films that have been modified with two types of molecules having identical 18-carbon alkyl chain termination and different surface attachments: octadecanethiol (ODT) and octadecyltriethoxysilane (OTES). We examined the functionalized surfaces using water contact angle measurements, Kelvin probe measurements, infrared absorbance spectroscopy, and atomic force microscopy. These have shown that OTES forms disordered incomplete monolayers, while ODT is prone to develop multilayered islands. Both treatments enhance polymer ordering. However, inverted solar cell devices fabricated with these treated interfaces performed very differently. ODT improves the short circuit current (J{sub SC}), open circuit voltage (V{sub OC}), and power conversion efficiency ({eta}), while these parameters all decrease in devices constructed from OTES-treated ZnO. The differences in V{sub OC} are related to modifications of the surface dipole associated with deposition of the two types of alkyl molecules, while changes in J{sub SC} are attributed to a balance between charge transfer blocking caused by the saturated hydrocarbon and the improved hole mobility in the polymer.
Abstract not provided
Photobleaching rates are investigated for thin films of poly(3-hexylthiophene) (P3HT) blends employing either an indene-C60 bisadduct (ICBA) or [6,6]-phenyl-C61-butyric acid methyl ester (PCBM) as the electron acceptor. Relative to the bisindene, PCBM significantly enhances resistance to photobleaching of the P3HT donor polymer. We tentatively attribute a decrease in the charge transfer rate asthe mechanism responsible for the more rapid photobleaching in the sample containing the bisindene adduct. In order to elucidate the influence of the photobleaching rate on the initial performance of unencapsulated devices, we also monitored the time-dependent behavior for P3HT:fullerene inverted devices. Under conditions of constant illumination, we observe essentially identical behavior indevice performance parameters regardless of the energy levels of the electron acceptor. We conclude that over the time frame measured for these devices, the primary degradation mechanism of the active layer is independent of the electron acceptor, despite the enhanced tolerance to photobleaching it may impart to the donor material.
Organic Photovoltaics (OPVs) recently attained power conversion efficiencies that are of interest for commercial production. Consequently, one of the most important unsolved issues facing a new industry is understanding what governs lifetime in organic devices and discovering solutions to mitigate degradation mechanisms. Historically, the active organic components are considered vulnerable to photo-oxidation and represent the primary degradation channel. However, we present several (shelf life and light soaking) studies pointing the relative stability of the active layers and instabilities in commonly used electrode materials. We show that engineering of the hole/electron layer at the electrode can lead to environmentally stable devices even without encapsulation.
The surface chemistry of ZnO single crystals of (0001) and (1010) orientations and ZnO nanorods was studied using x-ray and ultraviolet photoelectron spectroscopies. Air drying and UV-ozone preparations were studied in particular as chemical treatments that could be applied to poly(3-hexylthiophene) (P3HT)-ZnO solar cells to enhance performance. The UV-ozone treatment showed negligible effect by photoelectron spectroscopy on the ZnO single crystal surfaces, but brought about electronic shifts consistent with increased upward band bending by {approx}0.25 eV on the ZnO nanorod surface. Modest interface dipoles of {approx}0.15 and {approx}0.25 eV were measured between P3HT and the (1010) and (0001) single crystal orientations, respectively, with the dipole moment pointing from ZnO to the P3HT layer. The sol-gel films showed evidence of forming a small interface dipole in the opposite direction, which illustrates the difference in surface chemistry between the solution-grown ZnO and the ZnO single crystals.
Abstract not provided
Abstract not provided
Zinc oxide (ZnO) is an important material for hybrid inorganic-organic devices in which the characteristics of the interface can dominate both the structural and electronic properties of the system. These characteristics can be modified through chemical functionalization of the ZnO surface. One of the possible strategies involves covalent bonding of the modifier using silane chemistry. Whereas a significant body of work has been published regarding silane attachments to glass and SiO{sub 2}, there is less information about the efficacy of this method for controlling the surface of metal oxides. Here we report our investigation of molecular layers attached to polycrystalline ZnO through silane bonding, controlled by an amine catalyst. The catalyst enables us to use triethoxysilane precursors and thereby avoid undesirable multilayer formation. The polycrystalline surface is a practical material, grown by sol-gel processing, that is under active exploration for device applications. Our study included terminations with alkyl and phenyl groups. We used water contact angles, infrared spectroscopy, and X-ray photoemission spectroscopy to evaluate the modified surfaces. Alkyltriethoxysilane functionalization of ZnO produced molecular layers with submonolayer coverage and evidence of disorder. Nevertheless, a very stable hydrophobic surface with contact angles approaching 106{sup o} resulted. Phenyltriethoxysilane was found to deposit in a similar manner. The resulting surface, however, exhibited significantly different wetting as a result of the nature of the end group. Molecular layers of this type, with a variety of surface terminations that use the same molecular attachment scheme, should enable interface engineering that optimizes the chemical selectivity of ZnO biosensors or the charge-transfer properties of ZnO-polymer interfaces found in oxide-organic electronics.
No abstract prepared.