Engineering topics
Publications and source records attributed to Olson, Lawrence.
An overview describing the current organizational structure, center mission, and technology focus areas of the Ames Research Center will be presented. The presentation will highlight research of the Aeronautics Directorate with some emphasis on activities related to fighter aircraft technology. The presentation will be limited to viewgraph material that is publicly available.
Jet efflux characteristics are a determining factor in STOVL aircraft aero/propulsion induced effects. Subcritical jets may have core lengths which range up to 6 diameters. The shorter core length jets tend to entrain ambient air more rapidly, inducing larger hover lift losses, and decay more rapidly, reducing adverse ground erosion. In transition flight, shorter core length jets show a larger decrease in the lift loss and a slight decrease in nose-up pitching moment. Supercritical pressure ratio jets tend to have longer, higher pressure core lengths with a greater hazard for ground erosion. The decay in the fully developed region is similar for both subcritical and supercritical pressure ratio jets. For subsonic jets the decay is inversely proportional to the distance from the jet exit. In ground effect the supercritical jet induces an oscillating pressure distribution on the ground with reflected shocks and expansions which can increase ground erosion and, at low ground heights, cause non-monotonic lift loss variations.
Hover and ground-effect tests were conducted with the Lockheed-Martin Large Scale Powered Model (LSPM) during June-November 1995 at the NASA Ames Research Center's Outdoor Aerodynamics Research Facility (OARF). This was done in support of the Joint Strike Fighter (JSF) Program being lead by the Department of Defense. The program was previously metered to as the Joint Advanced Strike Technology (JAST) Program. The tests at the OARF included: engine thrust calibrations out of ground effect, measurements of individual nozzle jet pressure decay characteristics, and jet-induced hover force and moment measurements in and out of ground effect. The engine calibrations provide data correlating propulsion system throttle and nozzle settings to thrust forces and moments for the bare fuselage with the wings, canards, and tails removed. This provides propulsive forces and moments while minimizing any of the effects due to the presence of the airframe. The engine calibrations were used later to determine thrust for hover testing at the OARF and for transition testing which took place in the NASA Ames 80 by 120 foot Wind Tunnel. The jet decay characteristics reflect the jet entrainment properties and are related to the aircraft suckdown characteristics. The JSF program provided the opportunity to obtain model scale effects using two models; one at small scale and one at large scale. Examples of data from these tests will be presented out of ground effect which will demonstrate the effect of scale. For one JSF configuration, two small-scale models and one large-scale model were tested and obtained different values for the lift loss out of ground effect. These differences were examined and are found to be largely dependent on the jet efflux characteristics. The jet-induced hover forces and moments are presented in and out of ground effect. For the hover testing the model is methodically built up from the bare fuselage, to include the wings, canards, and vertical tails, to determine the effects of each. Other components such as weapons bay doors, landing gear doors, and other lift improvement devices and their effect on the jet-induced forces and moments are examined.
The performance of the Pratt & Whitney Advanced Ducted Propulsion (ADP) UHB concept has been recently evaluated with studies of a 17 in. diameter fan simulator. Following the model scale tests, a 118 in. diameter demonstrator was tested at the NASA Ames 40- by 80-Foot Wind Tunnel. The 18 blade fan was driven by the low compressor shaft of a PW2037 core through a reduction gear system fabricated by Fiat with approximately 1:3.7 reduction ratio. ne variable pitch fan was hydraulically actuated with settings for take-off, cruise, feather, and reverse thrust. The low-pressure turbine was built by MTU to provide higher shaft power in comparison with the standard PW2037. The demonstrator was provided with 45 vanes located 2.6 fan chords downstream of the rotor, and 10 case struts approximately 1 fan chord downstream of the vanes. The inlet, mid-duct, and exhaust linings were acoustically treated. Acoustic surveys were taken in the for-ward thrust mode for fan speeds of 898, 1120, 1205, and 1302 R.P.M., and at tunnel speeds of 25, 50, 100, and 140 kts. The lowest speed was achieved with the wind tunnel fans at flat pitch, but with the engine pumping the test section Microphone signals were recorded for 30 seconds at 5 deg. increments. These measurements will be used to assess the effects of forward speed on UHB engines, to compare these effects with the corresponding characteristics of conventional bypass ratio engines, and to discuss the various aspects of testing large engines in the wind tunnel.
The proposed paper presents flow visualization performed during experiments conducted on a full-scale F/A-18 aircraft in the 80- by 120-Foot Wind-Tunnel at NASA Ames Research Center. The purpose of the flow-visualization experiments was to document the forebody and leading edge extension (LEX) vortex interaction along with the wing flow patterns at high angles of attack and low speed high Reynolds number conditions. This investigation used surface pressures in addition to both surface and off-surface flow visualization techniques to examine the flow field on the forebody, canopy, LEXS, and wings. The various techniques used to visualize the flow field were fluorescent tufts, flow cones treated with reflective material, smoke in combination with a laser light sheet, and a video imaging system for three-dimension vortex tracking. The flow visualization experiments were conducted over an angle of attack range from 20 deg to 45 deg and over a sideslip range from -10 deg to 10 deg. The various visualization techniques as well as the pressure distributions were used to understand the flow field structure. The results show regions of attached and separated flow on the forebody, canopy, and wings as well as the vortical flow over the leading-edge extensions. This paper will also present flow visualization comparisons with the F-18 HARV flight vehicle and small-scale oil flows on the F-18.
Presented here is a comprehensive review of the following aerodynamics elements: computational methods and applications, computational fluid dynamics (CFD) validation, transition and turbulence physics, numerical aerodynamic simulation, drag reduction, test techniques and instrumentation, configuration aerodynamics, aeroacoustics, aerothermodynamics, hypersonics, subsonic transport/commuter aviation, fighter/attack aircraft and rotorcraft.