Search NASA⌕ Search

Engineering topics

Olsson, III, Roy H

Publications and source records attributed to Olsson, III, Roy H.

Microelectromechanical filter formed from parallel-connected lattice networks of contour-mode resonators

A microelectromechanical (MEM) filter is disclosed which has a plurality of lattice networks formed on a substrate and electrically connected together in parallel. Each lattice network has a series resonant frequency and a shunt resonant frequency provided by one or more contour-mode resonators in the lattice network. Different types of contour-mode resonators including single input, single output resonators, differential resonators, balun resonators, and ring resonators can be used in MEM filter. The MEM filter can have a center frequency in the range of 10 MHz-10 GHz, with a filter bandwidth of up to about 1% when all of the lattice networks have the same series resonant frequency and the same shunt resonant frequency. The filter bandwidth can be increased up to about 5% by using unique series and shunt resonant frequencies for the lattice networks.

42 ENGINEERING↗

Method for fabricating a microelectromechanical resonator

A method is disclosed which calculates dimensions for a MEM resonator in terms of integer multiples of a grid width G for reticles used to fabricate the resonator, including an actual sub-width L.sub.a=NG and an effective electrode width W.sub.e=MG where N and M are integers which minimize a frequency error f.sub.e=f.sub.d-f.sub.a between a desired resonant frequency f.sub.d and an actual resonant frequency f.sub.a. The method can also be used to calculate an overall width W.sub.o for the MEM resonator, and an effective electrode length L.sub.e which provides a desired motional impedance for the MEM resonator. The MEM resonator can then be fabricated using these values for L.sub.a, W.sub.e, W.sub.o and L.sub.e. The method can also be applied to a number j of MEM resonators formed on a common substrate.

42 ENGINEERING↗

Origins and mitigation of spurious modes in aluminum nitride microresonators.

Recently reported narrow bandwidth, <;2%, aluminum nitride microresonator filters in the 100-500 MHz range offer lower insertion loss, 100x smaller size, and elimination of large external matching networks, when compared to similar surface acoustic wave filters. While the initial results are promising, many microresonators exhibit spurious responses both close and far from the pass band which degrade the out of band rejection and prevent the synthesis of useful filters. This paper identifies the origins of several unwanted modes in overtone width extensional aluminum nitride microresonators and presents techniques for mitigating the spurious responses.

36 MATERIALS SCIENCE↗

NanoFIBrication of a two-dimensional phononic crystal in a free standing membrane.

A two-dimensional phononic crystal (PnC) that can operate in the GHz range is created in a freestanding silicon substrate using NanoFIBrication (using a focused ion beam (FIB) to fabricate nanostructures). First, a simple cubic 6.75 x 6.75 ?m array of vias with 150 nm spacing is generated. After patterning the vias, they are backfilled with void-free tungsten scatterers. Each via has a diameter of 48 nm. Numerical calculations predict this 2D PnC will generate a band gap near 22 GHz. A protective layer of chromium on top of the thin (100 nm) silicon membrane confines the surface damage to the chromium, which can be removed at a later time. Inspection of the underside of the membrane shows the vias flaring out at the exit, which we are dubbing the 'trumpet effect'. The trumpet effect is explained by modeling the lateral damage in a freestanding membrane.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Multi-frequency aluminum nitride micro-filters for advanced RF communications.

An AlN MEMS resonator technology has been developed, enabling massively parallel filter arrays on a single chip. Low-loss filter banks covering the 10 MHz--10-GHz frequency range have been demonstrated, as has monolithic integration with inductors and CMOS circuitry. The high level of integration enables miniature multi-bandm spectrally aware, and cognitive radios.

42 ENGINEERING↗

Research on micro-sized acoustic bandgap structures.

Phononic crystals (or acoustic crystals) are the acoustic wave analogue of photonic crystals. Here a periodic array of scattering inclusions located in a homogeneous host material forbids certain ranges of acoustic frequencies from existence within the crystal, thus creating what are known as acoustic (or phononic) bandgaps. The vast majority of phononic crystal devices reported prior to this LDRD were constructed by hand assembling scattering inclusions in a lossy viscoelastic medium, predominantly air, water or epoxy, resulting in large structures limited to frequencies below 1 MHz. Under this LDRD, phononic crystals and devices were scaled to very (VHF: 30-300 MHz) and ultra (UHF: 300-3000 MHz) high frequencies utilizing finite difference time domain (FDTD) modeling, microfabrication and micromachining technologies. This LDRD developed key breakthroughs in the areas of micro-phononic crystals including physical origins of phononic crystals, advanced FDTD modeling and design techniques, material considerations, microfabrication processes, characterization methods and device structures. Micro-phononic crystal devices realized in low-loss solid materials were emphasized in this work due to their potential applications in radio frequency communications and acoustic imaging for medical ultrasound and nondestructive testing. The results of the advanced modeling, fabrication and integrated transducer designs were that this LDRD produced the 1st measured phononic crystals and phononic crystal devices (waveguides) operating in the VHF (67 MHz) and UHF (937 MHz) frequency bands and established Sandia as a world leader in the area of micro-phononic crystals.

42 ENGINEERING↗