Engineering topics

Onchi, T.

Publications and source records attributed to Onchi, T..

3 records

DOE OSTI2023

Demonstration of transient CHI startup using a floating biased electrode configuration

Abstract Results from the successful solenoid-free plasma startup using the method of transient coaxial helicity injection (transient CHI) in the QUEST spherical tokamak (ST) are reported. Unlike previous applications of CHI on HIT-II and on NSTX which required two toroidal insulating breaks to the vacuum vessel, QUEST uses a first of its kind, floating single biased electrode configuration, which does not use such a vacuum break. Instead, the CHI electrode is simply insulated from the outer lower divertor plate support structure. This configuration is much more suitable for implementation in a fusion reactor than the previous configurations. Transient CHI generated toroidal currents of 135 kA were obtained. The toroidal current during the formation of a closed flux configuration was over 50 kA. These results bode well for the application of transient CHI in a new generation of compact high-field STs and tokamaks in which the space for the central solenoid is very restricted.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2022

Improvements to the High-Field-Side Transient CHI System on QUEST

Transient coaxial helicity injection (CHI) is a promising candidate for solenoid-free plasma current start-up in a low-aspect-ratio tokamak in support of developing fully non-inductive scenarios. The aim of the transient CHI research on QUEST is to develop a reactor-relevant CHI design. On QUEST, a CHI discharge is initiated by driving current along magnetic field lines that connect an electrically insulated electrode plate (which is referred to as a bias electrode) to a vessel component at the bottom region of the spherical tokamak. In the first application of CHI on QUEST, the electrically insulated electrode plate was biased with respect to the outer vessel in a configuration referred to as low-field-side (LFS) injection. To maintain a narrow injector flux footprint width throughout the discharge, QUEST is now developing a high-field-side (HFS) injection configuration, in which the electrically insulated electrode plate is biased with respect to the inner vessel components. Through the implementation of a CHI-dedicated gas injection system, studies in the HFS injection configuration have now demonstrated good magnetic flux evolution into the vacuum vessel. Toroidal currents up to 43 kA have been achieved, and the generated current has increased in proportion to the magnetic flux connecting the electrodes. Finally, these results which show agreement with the CHI-scaling suggest that much higher levels of toroidal current can be generated on QUEST in an optimized CHI system in which the magnetic flux connecting the CHI electrodes is further increased.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2022

Design Considerations for the Implementation of a High-Field-Side Transient CHI System on QUEST

Transient coaxial helicity injection (T-CHI), a method first developed on the small helicity injected torus (HIT-II) experiment and then validated on the much larger National Spherical Torus Experiment (NSTX) device, is a method to initiate an inductive-like tokamak plasma discharge without reliance on the central solenoid. A CHI discharge is initiated by driving current along magnetic flux that connects the inner and outer divertor plates on one end of the tokamak. To permit this, on both HIT-II and NSTX, toroidal ceramic insulators were used to electrically separate the inner and outer vessel components. The use of such large toroidal vacuum insulators may not be easy to implement in reactors. To address this issue, the Q-shu University experiments with steady-state spherical tokamak (ST) (QUEST) is developing a reactor-relevant CHI configuration in which one of the divertor plates is electrically insulated from the rest of the vessel. The first application of T-CHI on QUEST biased the CHI electrode to the outer vessel. While the CHI discharges could be easily generated, it was found that as the discharge filled the vessel, the separation distance between the injector magnetic flux footprints widened, a condition that is not favorable for the generation of closed flux surfaces. Biasing the electrode to the inner wall is a configuration similar to that used on NSTX and HIT-II, but initial testing in this configuration has proved to be challenging. The design described here overcomes the present limitation by locating the CHI electrode much closer to the CHI injector flux coil and using an NSTX-like gas injection manifold to enable high-field-side T-CHI startup on QUEST. Finally, the concepts described in this article should also benefit the future implementation of T-CHI systems in other tokamaks and spherical tokamaks.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗