Search NASA⌕ Search

Engineering topics

Ongena, J

Publications and source records attributed to Ongena, J.

At least 19 records

Influence of gas puff location on the coupling of lower hybrid waves in JET ELMy H-mode plasmas

Reliable coupling of the lower hybrid current drive (LHCD) to H-mode plasmas in JET is made feasible through a dedicated gas injection system, located at the outer wall and magnetically connected to the antenna (Pericoli Ridolfini et al 2004 Plasma Phys. Control. Fusion 46 349, Ekedahl et al 2005 Nucl. Fusion 45 351, Ekedahl et al 2009 Plasma Phys. Control. Fusion 51 044001). An experiment was carried out in JET in order to investigate whether a gas injection from the top of the torus, as is foreseen for the main gas injection in ITER, could also provide good coupling of the LH waves if magnetically connected to the antenna. The results show that a top gas injection was not efficient for providing a reliable LHCD power injection, in spite of being magnetically connected and in spite of using almost twice the amount of gas flow compared with the dedicated outer mid-plane gas puffing system. A dedicated gas injection system, set in the outer wall and magnetically connected to the LHCD antenna, is therefore recommended in order to provide the reliable coupling conditions for an LHCD antenna in ITER.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Implementation of load resilient ion cyclotron resonant frequency (ICRF) systems to couple high levels of ICRF power to ELMy H-mode plasmas in JET

The paper summarizes the continuous developments made to the ion cyclotron resonant frequency (ICRF) system at JET in order to improve the reliability of the power coupled to plasma. It details the changes and improvements made to the system so that more power is coupled during ELMy plasmas as well as increasing the power density to demonstrate reliable operation in the range of the requirements for ITER. Results obtained using the conventional matching (stubs and trombones) system, 3 dB couplers and the conjugate-T scheme with variable matching elements outside the wave launching structure (external conjugate-T) and inside the wave launching structure (ITER-like antenna) are described. The presence of the three different approaches to load resilient ICRF systems at JET creates a unique opportunity to compare these methods under very similar plasma conditions and to assess the results of ICRF power delivery to ELMy plasmas, an important issue for ITER. The impact of the availability of increased levels of reliable ICRF power on plasma physics studies in JET is illustrated.

43 PARTICLE ACCELERATORS↗

Heat loads from ICRF and LH wave absorption in the SOL: characterization on JET and implications for the ITER-Like Wall

Heat loads from ICRF and LH wave absorption in the SOL are characterized on JET from the de-convolution of surface temperatures measured by infrared thermography. The spatial localization, quantitative estimates, parametric dependence and physical origin of the observed heat fluxes are documented. Implications of these observations are discussed for the operation of JET with an ITER-Like Wall, featuring Beryllium tiles with reduced power handling capability.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

ICRF scenarios for ITER's half-field phase

The non-active operation phase of ITER will be done in H and {sup 4}He plasmas at half the nominal magnetic field, B{sub 0} = 2.65T. At this field and for the given frequency range of the ICRF system (f = 40-55MHz), three ICRF heating scenarios are available a priori: (i) Fundamental ICRH of majority H plasmas at f{approx_equal}40MHz,(ii) second harmonic (N= 2) {sup 3}He ICRH in H plasmas at f{approx_equal}53MHz and (iii) fundamental minority H heating in {sup 4}He plasmas at f{approx_equal}40MHz. While the latter is expected to perform well for not too large H concentrations, the heating scenarios available for the Hydrogen plasmas are less robust. Recent JET experiments performed in similar conditions to those expected in ITER's half-field phase confirmed the low performance of these two scenarios and numerical simulations have shown that the situation is not much improved in ITER, mainly because of the rather modest plasma temperature and density expected in its initial operation phase. A summary of the main experimental results obtained at JET followed by numerical predictions for ITER's half-field ICRF heating scenarios will be presented.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Enhancing The Mode Conversion Efficiency In JET Plasmas With Multiple Mode Conversion Layers

The constructive interference effect described by Fuchs et al. [1] shows that the mode conversion and thereby the overall heating efficiency can be enhanced significantly when an integer number of fast wave wavelengths can be folded in between the high field side fast wave cutoff and the ion-ion hybrid layer(s) at which the ion Bernstein or ion cyclotron waves are excited. This effect was already experimentally identified in ({sup 3}He)-D plasmas [2] and was recently tested in ({sup 3}He)-H JET plasmas. The latter is an 'inverted' scenario, which differs significantly from the ({sup 3}He)-D scenarios since the mode-conversion layer is positioned between the low field side edge of the plasma and the ion-cyclotron layer of the minority {sup 3}He ions (whereas the order in which a wave entering the plasma from the low field side encounters these layers is inverted in a 'regular' scenario), and because much lower {sup 3}He concentrations are needed to achieve the mode-conversion heating regime. The presence of small amounts of {sup 4}He and D in the discharges gave rise to an additional mode conversion layer on top of the expected one associated with {sup 3}He-H, which made the interpretation of the results more complex but also more interesting: Three different regimes could be distinguished as a function of X[{sup 3}He], and the differing dynamics at the various concentrations could be traced back to the presence of these two mode conversion layers and their associated fast wave cutoffs. Whereas (1-D and 2-D) numerical modeling yields quantitative information on the RF absorptivity, recent analytical work by Kazakov [3] permits to grasp the dominant underlying wave interaction physics.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Influence of Magnetic Field Ripple on the Intrinsic Rotation of Tokamak Plasmas

Using the unique capability of JET to monotonically change the amplitude of the magnetic field ripple, without modifying other relevant equilibrium conditions, the effect of the ripple on the angular rotation frequency of the plasma column was investigated under the conditions of no external momentum input. The ripple amplitude was varied from 0.08% to 1.5% in Ohmic and ion-cyclotron radio-frequency (ICRF) heated plasmas. In both cases the ripple causes counterrotation, indicating a strong torque due to nonambipolar transport of thermal ions and in the case of ICRF also fast ions.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

ICRF Wall Conditioning: Present Status and Developments for Future Superconducting Fusion Machines

ITER and future superconducting fusion machines need efficient wall conditioning techniques for routine operation in between shots in the presence of permanent high magnetic field for wall cleaning, surface isotope exchange and to control the in-vessel long term tritium retention. Ion Cyclotron Wall Conditioning (ICWC) based on the ICRF discharge is fully compatible and needs the presence of the magnetic field. The present paper focuses on the principal aspects of the ICWC discharge performance in large-size fusion machines: (i) neutral gas RF breakdown with conventional ICRF heating antennas, (ii) antenna coupling with low density ({approx}10{sup 17} m{sup -3}) RF plasmas and (iii) ICWC scenarios with improved RF plasma homogeneity in the radial and poloidal directions. All these factors were identified as crucial to achieve an enhanced conditioning effect (e.g. removal rates of selected 'marker' masses). All the observed effects are analyzed in terms of RF plasma wave excitation/absorption and compared with the predictions from 1-D RF full wave and 0-D RF plasma codes. Numerical modeling and empirical extrapolation from the existing machines give good evidence for the feasibility of using ICWC in ITER with the main ICRF antenna.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Present Status of the ITER-like ICRF Antenna on JET

The commissioning of the ITER-Like ICRF Antenna (ILA) on JET plasmas from May 2008 to April 2009 in various conditions (33, 42 and 47 MHz, L- and H-mode, antenna strap-plasma separatrix distances of {approx}9 to 17 cm) has provided relevant information for future antenna design and operation. The maximum power density achieved was 6.2 MW/m{sup 2} in L-mode with strap to plasma separatrix distance of {approx}9-10 cm at 42 MHz on the lower half of the ILA extrapolating to 8 MW/m{sup 2} if the full generator power had been available. Efficient (trip-free operation) ELM tolerance was obtained both at 33 and 42 MHz on a large range of ELMs with strap voltages up to 42 kV and a maximum power density of 4.1 MW/m{sup 2}. The paper reviews these achievements as well as remaining issues.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

RF Matching Feedback Control Systems on the JET ITER-Like Antenna

Ion Cyclotron Resonance Frequency (ICRF) antennas achieve maximum power transfer from RF generator to plasma load by establishing an impedance match. The JET ITER-Like Antenna (ILA) consists of 4 mutually coupled resonators that need to be matched simultaneously and whose resonant states need to be accurately controlled by several available actuators to couple maximum power and to achieve optimal ELM resilience. The operation of the matching system is described. Experimental operation revealed some phenomena and sensitivities that did not surface from simulation alone and that should be taken into account for the design of future ICRF antennae systems.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Simulating the JET ITER-like Antenna circuit

A set of simulation/interpretation tools based on transmission line theory and on the RF model developed by M. Vrancken has been developed to study the ITER-like Antenna (ILA) at JET. For given tuning element settings, the unique solution of the equations governing the ILA circuit requires solving a system of coupled linear equations relating the voltages and currents at the antenna straps and other key locations. This computation allows cross-checking predicted values against measured experimental ones. Further more, a minimization procedure allows improving the correspondence with the quantities measured in the circuit during shots, thus coping with unavoidable errors arising from uncertainties in the measurements or from inaccuracies in the adopted RF model. Typical applications are e.g. fine-tuning of the second-stage of the ILA circuit for increased ELM-resilience, cross-checking the calibration of the measurements throughout the circuit and predicting the antenna performance and matching conditions in new plasma scenarios.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Operational Experience with the Scattering Matrix Arc Detection System on the JET ITER-Like Antenna

The Scattering Matrix Arc Detection System (SMAD) has been fully deployed on all 4 sets of Resonant Double Loop (RDL), Vacuum Transmission Line (VTL) and Antenna Pressurised Transmission Lines (APTL) of the JET ICRF ITER-Like Antenna (ILA) and this has been indispensable for operating at low (real) T-point impedance values to investigate ELM tolerance. This paper describes the necessity of the SMAD vs VSWR (Voltage Standing Wave Ratio) protection system, SMAD commissioning, problems and a number of typical events detected by the SMAD system during operation on plasma.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

LH power modulation experiment on JET

LH power modulation was recently used at JET to quantify experimentally the LH current drive efficiency and power deposition. A new approach was applied for the analysis of the amplitude and phase of electron temperature T{sub e} perturbations {delta}T{sub e}(k{omega}{sub o}) at different harmonics k of the modulation frequency {omega}{sub o}. A solution of the Fokker-Planck equation combined with heat transport modelling was used to study the dependence of the ratio of the perturbation of different harmonics k and n, {delta}T{sub e}(k{omega}{sub o})/{delta}T{sub e}(n{omega}{sub o}), and the phase shift of the harmonics {delta}{phi}(k{omega}{sub o}) on the plasma parameters and electron distribution function plateau width, which is directly connected to the current drive efficiency. The results of the modelling were compared with the experimental data to estimate the current drive efficiency. In addition, LH power deposition profiles were deduced from the radial dependence of {delta}{phi}({omega}{sub o}). The maximum of the LH power deposition becomes more peripheral and with a reduced current drive efficiency at higher densities. In H-Mode plasmas, at pedestal densities above the LH accessibility limit, a large fraction of the power is absorbed beyond the separatrix. Finally, the experimental power deposition profiles are more peripheral than the calculated ones obtained from combined ray tracing and Fokker-Planck Plank modelling. The experimental results indicate that the LH power spectrum in the plasma is modified, with more power in the high N// components.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Impurity Radiation for Detecting Arcs during High Lower Hybrid Power Transmission at JET

During high power commissioning of the JET LH launcher, the radiation and impurity release has been analyzed from various diagnostics: VUV and visible spectroscopy, bolometry. These two last diagnostics have lines-of-sight viewing the launcher and can provide information about the electron and/or impurity source localisation. Using a database of 800 plasmas, it is concluded that the iron contamination (FeXV and FeXXIII) is very low for 94% of the pulses and increases linearly with LH power. During arcs, a strong and fast increase of the radiation along the line-of-sight viewing the launcher is observed. This diagnostic could provide a tool for arc detection complementary to the RF measurements aiming at reducing the metal contamination in the plasma.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

LH Power Losses In Front of the JET Launcher

In recent JET experiments, Lower Hybrid (LH) power losses in the Scrape-Off Layer (SOL) were characterized using infra-red (IR) thermography. Hot spots were observed on objects intercepting the field lines passing in front of the LH launcher, i.e. on poloidal limiters and on dumplates located at the top of the tokamak; their locations being in good agreement with magnetic field line tracing using the EFIT equilibrium code. The dumplate temperature was monitored while scanning the launcher position so that the radial distance between field lines intercepting the hot spots and the launcher was increased up to 3.5 cm. The dissipation layer in front of the launcher was estimated to be at least 3.5 cm wide, in agreement with recent measurements on Tore-Supra, but not with simple models that predict a dissipation layer in the mm range.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Overview of Recent Results on Heating and Current Drive in the JET tokamak

In this paper, significant results in the heating and current drive domains obtained at JET in the past few years following systems upgrade and dedicated experimental time, will be reviewed. Firstly, an overview of the new Ion Cyclotron Resonance Frequency (ICRF) heating capabilities will be presented i.e. results from the ITER-Like ICRF antenna (ILA), the use of External Conjugate-T and 3dB hybrid couplers to increase the ICRF power during ELMy H-mode. Furthermore, experiments to study the influence of the phasing of the ICRF antenna on power absorption and coupling will be described. Looking at Low Hybrid (LH) issues for ITER, the effect of the location of gas injection on the LH coupling improvement at large launcher-separatrix distances will be discussed as the possibility to operate at ITER-relevant power densities. Experiments to characterise the LH power losses in the Scrape-Off-Layer (SOL) and to determine the LH wave absorption and current drive using power modulation will be shown. Finally, plasma rotation studies in the presence of ICRF heating with standard and enhanced JET toroidal field ripple will be presented.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Recent experiments on alternative dipole phasing with the JET A2 ICRF antennas

Using the JET A2 ICRF antennas, experiments were carried out to assess the performance of three different dipole phasing configurations relevant for the operation of the ICRF antenna in ITER. Three similar discharges with dipole (0{pi}0{pi}), 'symmetric dipole' (0{pi}{pi}0) and 'super dipole' (00{pi}{pi}) phasings were compared. In the 'super dipole' case, higher coupling was confirmed but lower heating efficiency and much stronger plasma wall interaction were observed, as corroborated, respectively, by the analysis of the diamagnetic energy response to the ICRF power steps and by the observation of a considerable temperature rise of the antenna limiters and septa in the 00{pi}{pi} case. These observations were found to be in line with simulations of the ICRF wave absorption and with High Frequency Structure Simulator (HFSS) modelling of the RF fields near the antenna.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Progress Testing TRANSP-TORIC Simulations of ICRH in JE

Introduction - Ion Cyclotron Range of Frequency (ICRF) waves are candidates for heating (ICRH), current drive, and possible flow drive in ITER and future tokamaks. There are considerable challenges developing the technology of ICRF systems and the tools for assessing effects on plasma performance. These tools are important both for guiding present experiments and for indicating efforts for future research. This paper addresses some of the tools for simulating ICRH. The TORIC ICRF full-wave code [1] solves the kinetic wave equation in 2D axisymmetric equilibria. TORIC solves Maxwell's Equations for a fixed wave frequency with a linear plasma response in a mixed spectral-finite element basis. The antenna is modelled as a sheet current. A kinetic model for the plasma dielectric response is derived using an Eikonal ansatz.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗