Search NASA⌕ Search

Engineering topics

Onjun, T

Publications and source records attributed to Onjun, T.

Simulations of plasma behavior during pellet injection in ITER

Plasma behavior during pellet injection in ITER is investigated using a 1.5D BALDUR integrated predictive modeling code. In these simulations, the pellet ablation is described using the neutral gas shielding (NGS) model developed by Parks and Turnbull [Phys. Fluids 21, 1735 (1978)]. The NGS pellet ablation model that includes the {nabla}B drift effect is coupled with a plasma core transport model, which is a combination of an MMM95 anomalous transport model and an NCLASS neoclassical transport model. The combination of core transport models, together with pellet model, is used to simulate the time evolution of plasma current, ion and electron temperatures, and density profiles for ITER standard type-I ELMy H-mode discharges during the pellet injection. It is found that the injection of pellet can result in either enhancement or degradation of plasma performance. The {nabla}B drift effect on the pellet deposition is very strong in ITER. The plasma density with high field side pellets, which favorable with the {nabla}B drift effect, is much higher and pellet can penetrate much deeper than that with low field side pellets.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Pellet injection into H-mode ITER plasma with the presence of internal transport barriers

The impacts of pellet injection into ITER type-1 ELMy H-mode plasma with the presence of internal transport barriers (ITBs) are investigated using self-consistent core-edge simulations of 1.5D BALDUR integrated predictive modeling code. In these simulations, the plasma core transport is predicted using a combination of a semi-empirical Mixed B/gB anomalous transport model, which can self-consistently predict the formation of ITBs, and the NCLASS neoclassical model. For simplicity, it is assumed that toroidal velocity for {omega}{sub E Multiplication-Sign B} calculation is proportional to local ion temperature. In addition, the boundary conditions are predicted using the pedestal temperature model based on magnetic and flow shear stabilization width scaling; while the density of each plasma species, including both hydrogenic and impurity species, at the boundary are assumed to be a large fraction of its line averaged density. For the pellet's behaviors in the hot plasma, the Neutral Gas Shielding (NGS) model by Milora-Foster is used. It was found that the injection of pellet could result in further improvement of fusion performance from that of the formation of ITB. However, the impact of pellet injection is quite complicated. It is also found that the pellets cannot penetrate into a deep core of the plasma. The injection of the pellet results in a formation of density peak in the region close to the plasma edge. The injection of pellet can result in an improved nuclear fusion performance depending on the properties of pellet (i.e., increase up to 5% with a speed of 1 km/s and radius of 2 mm). A sensitivity analysis is carried out to determine the impact of pellet parameters, which are: the pellet radius, the pellet velocity, and the frequency of injection. The increase in the pellet radius and frequency were found to greatly improve the performance and effectiveness of fuelling. However, changing the velocity is observed to exert small impact.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Impacts of pellets injected from the low-field side on plasma in ITER

Impacts of pellets injected from the low-field side (LFS) on plasma in ITER are investigated using the 1.5D BALDUR integrated predictive modeling code. In these simulations, the pellet ablation is described using the neutral gas shielding (NGS) model. The pellet ablation model is coupled with the plasma core transport model, which is a combination of the MMM95 anomalous transport model and NCLASS neoclassical transport model. The boundary conditions are assumed to be at the top of the pedestal, in which the pedestal parameters are predicted using a pedestal model based on the theoretical-based pedestal width scaling (either magnetic and flow shear stabilization width scaling, or flow shear stabilization width scaling, or normalized poloidal pressure width scaling) and the infinite-n ballooning mode pressure gradient limit. These pedestal models depend sensitively on the density at the top of the pedestal, which can be strongly influenced by the injection of pellets. The combination of the MMM95 and NCLASS models, together with the pedestal and NGS models, is used to simulate the time evolution of the plasma current, ion and electron temperatures, and density profiles for ITER standard type-I ELMy H-mode discharges during the injection of LFS pellets. It is found that the injection of pellets results in a complicated plasma scenario, especially in the outer region of the plasma and the plasma conditions at the boundary in which the pellet has an impact on increasing the plasma edge density, but reducing the plasma edge temperature. The LFS pellet has a stronger impact on the edge as compared to the center. For fusion performance, the pellet can result in either enhancement or degradation, depending sensitively on the pellet parameters; such as the pellet size, pellet velocity, and pellet frequency. For example, when a series of deuterium pellets with a size of 0.5 cm, velocity of 1 km/s, and frequency of 2 Hz are injected into the ITER plasma from the LFS, the plasma performance, evaluated in terms of Q{sub fusion}, can increase to 72% of that before the use of pellets. It is also found that the injection of pellets results in an increase in the ion and electron densities, but does not enhance the central plasma density. On the other hand, it results in the formation of another peak of the plasma density in the outer region near the plasma edge. The formation of the density peak results in the reduction of plasma transports near the edge by decreasing the contributions of ion-temperature-gradient and trapped electron modes, as well as kinetic ballooning modes.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Behaviors of impurity in ITER plasma with standard type I ELMy H-mode and steady-state scenarios

Self-consistent simulations of impurity behaviors in ITER plasmas in standard Type I ELMy H-mode and steady-state scenarios are investigated using 1.5D BALDUR integrated predictive modeling code. In these simulations, the plasma core transports, including electron and ion thermal, hydrogenic and impurity transports, are predicted using a linear combination of anomalous and neoclassical transports. An anomalous transport is calculated using a theory-based Multimode (MMM95) model; while the neoclassical transport is calculated using NCLASS model. The temperature and density boundary conditions are described at the top of the pedestal. Two different models for hydrogenic and impurity boundary density conditions are considered. The first model is called a 'static boundary density model,' in which the hydrogenic and impurity densities at the boundary are fixed. For the second model, called a 'dynamic boundary density model,' the hydrogenic and impurity densities at the boundary are assumed to be a large fraction of its line-averaged density. For simplicity, the pedestal temperature is assumed to be a constant in all simulations. The combination of a core transport model together with the boundary density models is used to simulate the time evolution of plasma current, temperature, and density profiles for ITER plasmas in standard type I ELMy H-mode and steady-state scenarios. As a result, the behaviors of impurity in ITER plasmas can be investigated. It is found in both ITER scenarios that the total amount of impurity, including beryllium and helium, in plasma core increases rapidly in early state and reaches a steady-state value. The level of impurity content in the steady state depends sensitively on the impurity boundary conditions. The effective charge at the edge is found to be about 1.4 and 1.1 using a static boundary density model and a dynamic boundary density model, respectively. It is also found that the hydrogenic and impurity transports in ITER plasmas for both scenarios is dominated by the kinetic ballooning modes, while the ITG and TEM modes provide the largest contributions for both thermal transports in most of region. In addition, a sensitivity study is carried out to investigate the impacts of pedestal temperature, pedestal density and line-averaged density on the impurity behaviors. It is found that increasing the pedestal temperature results in a reduction of the impurity content. On the other hand, increasing the pedestal density, line-averaged density or impurity influx result in an increase of the impurity content.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Simulation study of HL-2A-like plasma using integrated predictive modeling code

Self-consistent simulations of HL-2A-like plasma are carried out using 1.5D BALDUR integrated predictive modeling code. In these simulations, the core transport is predicted using the combination of Multi-mode (MMM95) anomalous core transport model and NCLASS neoclassical transport model. The evolution of plasma current, temperature and density is carried out. Consequently, the plasma current, temperature and density profiles, as well as other plasma parameters, are obtained as the predictions in each simulation. It is found that temperature and density profiles in these simulations are peak near the plasma center. In addition, the sawtooth period is studied using the Porcilli model and is found that before, during, and after the electron cyclotron resonance heating (ECRH) operation the sawtooth period are approximately the same. It is also observed that the mixing radius of sawtooth crashes is reduced during the ECRH operation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗