Engineering topics

Onyszchuk, I. M.

Publications and source records attributed to Onyszchuk, I. M..

3 records

NASA NTRS1991

Coding gains and error rates from the Big Viterbi Decoder

A prototype hardware Big Viterbi Decoder (BVD) was completed for an experiment with the Galileo Spacecraft. Searches for new convolutional codes, studies of Viterbi decoder hardware designs and architectures, mathematical formulations, and decompositions of the deBruijn graph into identical and hierarchical subgraphs, and very large scale integration (VLSI) chip design are just a few examples of tasks completed for this project. The BVD bit error rates (BER), measured from hardware and software simulations, are plotted as a function of bit signal to noise ratio E sub b/N sub 0 on the additive white Gaussian noise channel. Using the constraint length 15, rate 1/4, experimental convolutional code for the Galileo mission, the BVD gains 1.5 dB over the NASA standard (7,1/2) Maximum Likelihood Convolution Decoder (MCD) at a BER of 0.005. At this BER, the same gain results when the (255,233) NASA standard Reed-Solomon decoder is used, which yields a word error rate of 2.1 x 10(exp -8) and a BER of 1.4 x 10(exp -9). The (15, 1/6) code to be used by the Cometary Rendezvous Asteroid Flyby (CRAF)/Cassini Missions yields 1.7 dB of coding gain. These gains are measured with respect to symbols input to the BVD and increase with decreasing BER. Also, 8-bit input symbol quantization makes the BVD resistant to demodulated signal-level variations which may cause higher bandwidth than the NASA (7,1/2) code, these gains are offset by about 0.1 dB of expected additional receiver losses. Coding gains of several decibels are possible by compressing all spacecraft data.

Onyszchuk, I. M.↗

NASA NTRS1991

Testing interconnected VLSI circuits in the Big Viterbi Decoder

The Big Viterbi Decoder (BVD) is a powerful error-correcting hardware device for the Deep Space Network (DSN), in support of the Galileo and Comet Rendezvous Asteroid Flyby (CRAF)/Cassini Missions. Recently, a prototype was completed and run successfully at 400,000 or more decoded bits per second. This prototype is a complex digital system whose core arithmetic unit consists of 256 identical very large scale integration (VLSI) gate-array chips, 16 on each of 16 identical boards which are connected through a 28-layer, printed-circuit backplane using 4416 wires. Special techniques were developed for debugging, testing, and locating faults inside individual chips, on boards, and within the entire decoder. The methods are based upon hierarchical structure in the decoder, and require that chips or boards be wired themselves as Viterbi decoders. The basic procedure consists of sending a small set of known, very noisy channel symbols through a decoder, and matching observables against values computed by a software simulation. Also, tests were devised for finding open and short-circuited wires which connect VLSI chips on the boards and through the backplane.

Onyszchuk, I. M.↗

NASA NTRS1989

Quantization effects in Viterbi decoding rate 1/n convolutional codes

A Viterbi decoder's performance loss due to quantizing data from the additive white Gaussian noise (AWGN) channel is studied. An optimal quantization scheme and branch metric calculation method are presented. The uniformly quantized channel capacity C(sub u)(q) is used to determine the smallest number of quantization bits q that does not cause a significant loss. The quantizer stepsize which maximizes C(sub u)(q) almost minimizes the decoder bit error rate (BER). However, a slightly larger stepsize is better, like the value that minimizes the Bhattacharyya bound. The range and renormalization of state metrics is analyzed, in particular for K = 15 decoders such as the Big Viterbi Decoder (BVD) for the Galileo mission. These results are required to design reduced hardware complexity Viterbi decoders with a negligible quantization loss.

Onyszchuk, I. M.↗