Engineering topics

Ophus, C.

Publications and source records attributed to Ophus, C..

4 records

DOE OSTI2023

Resolution of Virtual Depth Sectioning from Four-Dimensional Scanning Transmission Electron Microscopy

Abstract One approach to three-dimensional structure determination using the wealth of scattering data in four-dimensional (4D) scanning transmission electron microscopy (STEM) is the parallax method proposed by Ophus et al. (2019. Advanced phase reconstruction methods enabled by 4D scanning transmission electron microscopy, Microsc Microanal25, 10–11), which determines the scattering matrix and uses it to synthesize a virtual depth-sectioning reconstruction of the sample structure. Drawing on an equivalence with a hypothetical confocal imaging mode, we derive contrast transfer and point spread functions for this parallax method applied to weakly scattering objects, showing them identical to earlier depth-sectioning STEM modes when only bright field signal is used, but that improved depth resolution is possible if dark field signal can be used. Through a simulation-based study of doped Si, we show that this depth resolution is preserved for thicker samples, explore the impact of shot noise on the parallax reconstructions, discuss challenges to making use of dark field signal, and identify cases where the interpretation of the parallax reconstruction breaks down.

3D imaging↗

DOE OSTI2023

The mechanism of twin thickening and the elastic strain state of TWIP steel nanotwins

A Twinning Induced Plasticity (TWIP) steel with a nominal composition of Fe-16.4Mn-0.9C-0.5Si-0.05Nb-0.05V was deformed to an engineering strain of 6%. The strain around the deformation twins were mapped using the 4D-STEM technique. Strain mapping showed a large average elastic strain of approximately 6% in the directions parallel and perpendicular to the twinning direction. However, the large average strain comprised of several hot spots of even larger strains of up to 12%. These hot spots could be attributed to a high density of sessile Frank dislocations on the twin boundary and correspond to shear stresses of 1–1.5 GPa. The strain and therefore stress fields are significantly larger than other materials known to twin and are speculated to be responsible for the early thickness saturation of TWIP steel nanotwins. The ability to keep twins extremely thin helps improve grain fragmentation, i.e. the dynamic Hall–Petch effect, and underpins the large elongations and strain hardening rates in TWIP steels.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Characterization of the atomic-level structure of γ-alumina and (111) Pt/γ-alumina interfaces

The atomic-level structure of platinum/γ-alumina interfaces is characterized in a model system of dense γ-alumina embedded with faceted Pt NPs produced by implantation of platinum ions into sapphire followed by thermal annealing in air at 800 °C. Aberration-corrected scanning transmission electron microscopy (STEM) was used to collect atomic-resolution images, which are compared to STEM image simulations of two experimentally-based bulk models of γ-alumina by Smrčok et al. and Zhou and Snyder. A density functional theory (DFT) based model of (111) interfaces with different chemical terminations (O, Al 1 , Al 2 ) of the γ-alumina developed by Oware Sarfo et al. is also compared to experimental STEM data from Pt/γ-alumina interfaces. Further, the Smrčok γ-alumina model provides a better fit than the Zhou structure to the bulk of the γ-alumina. The oxygen-terminated Oware Sarfo model best fits the experimental data and is a very good model close to the interface. However, the fit of the interface model to the experimental data is poorer beyond the third atomic layer in the γ-alumina. This is attributed to compromises required in the design of the model to limit the cell size and computational time for DFT calculations. Understanding the accuracy and limits of the structural models of γ-alumina and Pt/γ-alumina interfaces is important to further the understanding of the structure/property relationships in this system.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Creation of skyrmions in van der Waals ferromagnet Fe 3 GeTe 2 on (Co/Pd) n superlattice

Magnetic skyrmions are topological spin textures, which usually exist in noncentrosymmetric materials where the crystal inversion symmetry breaking generates the so-called Dzyaloshinskii-Moriya interaction. This requirement unfortunately excludes many important magnetic material classes, including the recently found two-dimensional van der Waals (vdW) magnetic materials, which offer unprecedented opportunities for spintronic technology. Using photoemission electron microscopy and Lorentz transmission electron microscopy, we investigated and stabilized Néel-type magnetic skyrmion in vdW ferromagnetic Fe 3 GeTe 2 on top of (Co/Pd) n in which the Fe 3 GeTe 2 has a centrosymmetric crystal structure. We demonstrate that the magnetic coupling between the Fe 3 GeTe 2 and the (Co/Pd) n could create skyrmions in Fe 3 GeTe 2 without the need of an external magnetic field. Our results open exciting opportunities in spintronic research and the engineering of topologically protected nanoscale features by expanding the group of skyrmion host materials to include these previously unknown vdW magnets.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗