Engineering topics
Orphee, Juan
Publications and source records attributed to Orphee, Juan.
Guidance, Navigation, and Control for NASA Lunar Pallet Lander
The NASA Lander Technology project is leading the development and integration of the Lunar Pallet Lander (LPL) concept. The objective is to demonstrate precision landing by delivering a payload to the lunar surface within 100 meters of a landing target. Potential landing sites are selected near the lunar pole where water may be present in permanently shadowed regions that could enable future in-situ resource utilization. The LPL is part of a sequence of missions aimed at maturing the necessary technologies, such as lunar precision landing sensors, that will enable the next generation of multi-ton lunar payloads and human landers. This paper provides an overview of the Mission Design, Guidance Navigation and Control (GNC) algorithms, and sensor suite. The results show the LPL simulated trajectory and landing precision performance under nominal and dispersed conditions. The landing precision simulation confirms the need to rely on high-accuracy navigation techniques and sensors such as Terrain Relative Navigation (TRN) and the Navigation Doppler Lidar (NDL), currently being developed for space applications. The results also demonstrate the ability of the guidance and control system to perform a soft lunar touchdown by combining thrust vector control during the solid rocket motor deceleration phase, and pulse engine control, for the liquid powered descent phase.
Mission Design for the Lunar Pallet Lander
Due to lighting conditions, the program decided to only fly to the north pole in June 2022 and south pole in December 2022. Starting with the June 2022 landing sites at the north pole, a trajectory scan was run for one landing per day for the latitudes from 85 up to 88 degrees at 0.5 degree increments. Each landing site was at lunar dawn, which determined the landing site’s longitude as described in the previous section. The results of the June 2022 scan showed that LPL had the capability to reach a landing site at least once per day for the region examined as see in in Figure 12. There appears to be a correlation between the landing site’s altitude and the propellant remaining above the lander’s FPR, Figure 13. This is most likely due to the >10 km altitude constraint at SRM burnout. This constraint was applied to keep the lander high above the lunar terrain to avoid mountains, but can be relaxed when the full terrain data is added. Figure 12. June 2022 Nominal Usable Propellant Remaining vs Landing Date/time Similarly, the December 2022 landing sites were run showing that LPL was also capable of reaching a landing site at the Moon at least once per day. Figure 14 shows the results of the December scan, however, there were 3 landing sites that LPL could not reach. Two were very low in altitude (-5 and -4 km in altitude), which looking at the altitude trends in Figure 15, indicates that these sites may not be feasible with the current mission design. It may be possible to achieve the low altitude landing sites by lowering the SRM burnout altitude constraint, but that requires detailed terrain modeling, planned for a future phase of the analysis. The third non-reachable landing site is most likely due to an optimization error, as its altitude was high enough, at -2 km, that it should not have been a problem for the lander to arrive there. More analysis is required to verify this observation.
Navigation Requirements Development and Performance Assessment of a Martian Ascent Vehicle
To support development of Martian Ascent Vehicles, analysis tools are needed to support the development of Guidance, Navigation, and Control requirements. This paper presents a focused approach to Navigation analysis to capture development of requirements on initial state knowledge and inertial sensor capabilities. A simulation and analysis framework was used to assess the capability of a range of sensors to operate inertially along a range of launch trajectories. The baseline Martian Ascent Vehicle was used as the input for optimizing a set of trajectories from each launch site. These trajectories were used to perform Monte Carlo analysis dispersing error sensor terms and their effects on integrated vehicle performance. Additionally, this paper provides insight into the use of optical navigation techniques to assess state determination and the potential to use observations of local extraplanetary bodies to estimate state. This paper provides an initial level of performance assessment of navigation components to support continued requirements development of a Martian Ascent Vehicle with applications to both crew and sample return missions.
Solar Torque Management for the Near Earth Asteroid (NEA) Scout CubeSat Using Center of Mass Position Control
No abstract available
Solar Torque Management for the Near Earth Asteroid Scout CubeSat Using Center of Mass Position Control
A novel mechanism, the Active Mass Translator (AMT), has been developed for the NASA Near Earth Asteroid (NEA) Scout mission to autonomously manage the spacecraft momentum. The NEA Scout CubeSat will launch as a secondary payload onboard Exploration Mission 1 of the Space Launch System. To accomplish its mission, the CubeSat will be propelled by an 86 square-meter solar sail during its two-year journey to reach asteroid 1991VG. NEA Scout's primary attitude control system uses reaction wheels for holding attitude and performing slew maneuvers, while a cold gas reaction control system performs the initial detumble and early trajectory correction maneuvers. The AMT control system requirements, feedback architecture, and control performance will be presented. The AMT reduces the amount of reaction control propellant needed for momentum management and allows for smaller capacity reaction wheels suitable for the limited 6U spacecraft volume. The reduced spacecraft mass allows higher in-space solar sail acceleration, thus reducing time-of-flight. The reduced time-of-flight opens the range of possible missions, which is limited by the lifetime of typical non-radiation tolerant CubeSat avionics exposed to the deep-space environment.
Cold Gas Reaction Control System (RCS) for the Near Earth Asteroid (NEA) Scout CubeSat
No abstract available
Cold Gas Reaction Control System for the Near Earth Asteroid Scout CubeSat
This paper describes the Attitude Control System (ACS) for the Near Earth Asteroid (NEA) Scout cubesat with particular focus on the Reaction Control System (RCS). NEA Scout is a 6-Unit cubesat with an 86-square-meter solar sail. NEA Scout will launch on Space Launch System (SLS) Exploration Mission 1 (EM-1), currently scheduled to launch in 2019. The spacecraft will rendezvous with an asteroid after a two year journey, and will conduct science imagery. The ACS consists of three major actuating subsystems: a Reaction Wheel (RW) control system, a Reaction Control System (RCS), and an Active Mass Translator (AMT) system. The three subsystems allow for a wide range of spacecraft attitude control capabilities, needed for the different phases of the NEA-Scout mission. The RCS performs a number of critical functions during NEA Scout’s mission. These requirements are described and the performance for achieving these requirements is shown. Moreover, NEA Scout employs a solar sail for long-duration propulsion. Solar sails are large, flexible structures that typically have low bending-mode frequencies. This paper demonstrates a robust performance while avoiding excitation of the sail’s structural modes.
Cold Gas Reaction Control System for the Near Earth Asteroid Scout CubeSat
This paper describes the Attitude Control System (ACS) for the Near Earth Asteroid (NEA) Scout cubesat with particular focus on the Reaction Control System (RCS). NEA Scout is a 6U cubesat with an 86 square-meter solar sail. NEA Scout will launch on Space Launch System (SLS) Exploration Mission 1 (EM-1), currently scheduled to launch in 2018. The spacecraft will rendezvous with an asteroid after a two year journey, and will conduct science imagery. The ACS consists of three major actuating subsystems: a Reaction Wheel (RW) control system, a Reaction Control System (RCS), and an Active Mass Translator (AMT) system. The three subsystems allow for a wide range of spacecraft attitude control capabilities, needed for the different phases of the NEA-Scout mission. The RCS performs a number of critical functions during NEA Scout's mission. These requirements are described and the performance for achieving these requirements is shown. Moreover, NEA Scout employs a solar sail for long-duration propulsion. Solar sails are large, flexible structures that typically have low bending-mode frequencies. This paper demonstrates a robust performance while avoiding excitation of the sail's structural modes.
Solar Sail Attitude Control System for the NASA Near Earth Asteroid Scout Mission
An Attitude Control System (ACS) has been developed for the NASA Near Earth Asteroid (NEA) Scout mission. The NEA Scout spacecraft is a 6U cubesat with an eighty-six square meter solar sail for primary propulsion that will launch as a secondary payload on the Space Launch System (SLS) Exploration Mission 1 (EM-1) and rendezvous with a target asteroid after a two year journey, and will conduct science imagery. The spacecraft ACS consists of three major actuating subsystems: a Reaction Wheel (RW) control system, a Reaction Control System (RCS), and an Active Mass Translator (AMT) system. The reaction wheels allow fine pointing and higher rates with low mass actuators to meet the science, communication, and trajectory guidance requirements. The Momentum Management System (MMS) keeps the speed of the wheels within their operating margins using a combination of solar torque and the RCS. The AMT is used to adjust the sign and magnitude of the solar torque to manage pitch and yaw momentum. The RCS is used for initial de-tumble, performing a Trajectory Correction Maneuver (TCM), and performing momentum management about the roll axis. The NEA Scout ACS is able to meet all mission requirements including attitude hold, slews, pointing for optical navigation and pointing for science with margin and including flexible body effects. Here we discuss the challenges and solutions of meeting NEA Scout mission requirements for the ACS design, and present a novel implementation of managing the spacecraft Center of Mass (CM) to trim the solar sail disturbance torque. The ACS we have developed has an applicability to a range of potential missions and does so in a much smaller volume than is traditional for deep space missions beyond Earth.
Flex Dynamics Avoidance Control of the NEA Scout Solar Sail Spacecraft's Reaction Control System
The Attitude Control System (ACS) is developed for a Near Earth Asteroid (NEA) Scout mission using a solar sail. The NEA-Scout spacecraft is a 6U cubesat with an 86 square-meter solar sail. NEA Scout will launch on Space Launch System (SLS) Exploration Mission 1 (EM-1), currently scheduled to launch in 2018. The spacecraft will rendezvous with a target asteroid after a two year journey, and will conduct science imagery. The solar sail spacecraft ACS consists of three major actuating subsystems: a Reaction Wheel (RW) control system, a Reaction Control System (RCS), and an Adjustable Mass Translator (AMT) system. The three subsystems allow for a wide range of spacecraft attitude control capabilities, needed for the different phases of the NEA-Scout mission. Because the sail is a flexible structure, care must be taken in designing a control system to avoid exciting the structural modes of the sail. This is especially true for the RCS, which uses pulse actuated, cold-gas jets to control the spacecraft's attitude. While the reaction wheels can be commanded smoothly, the RCS jets are simple on-off actuators. Long duration firing of the RCS jets - firings greater than one second - can be thought of as step inputs to the spacecraft's torque. On the other hand, short duration firings - pulses on the order of 0.1 seconds - can be thought of as impulses in the spacecraft's torque. These types of inputs will excite the structural modes of the spacecraft, causing the sail to oscillate. Sail oscillations are undesirable for many reasons. Mainly, these oscillations will feed into the spacecraft attitude sensors and pointing accuracy, and long term oscillations may be undesirable over the lifetime of the solar sail. In order to limit the sail oscillations, an RCS control scheme is being developed to minimize sail excitations. Specifically, an input shaping scheme similar to the method described in Reference 1 will be employed. A detailed description of the RCS control scheme will be provided with particular emphasis on flexible body excitation. The RCS performance will be provided to show that sail and boom excitation is minimized.
Momentum Management for the NASA Near Earth Asteroid Scout Solar Sail Mission
The Momentum Management (MM) system is described for the NASA Near Earth Asteroid Scout (NEA Scout) cubesat solar sail mission. Unlike many solar sail mission proposals that used solar torque as the primary or only attitude control system, NEA Scout uses small reaction wheels (RW) and a reaction control system (RCS) with cold gas thrusters, as described in the abstract "Solar Sail Attitude Control System for Near Earth Asteroid Scout Cubesat Mission." The reaction wheels allow fine pointing and higher rates with low mass actuators to meet the science, communication, and trajectory guidance requirements. The MM system keeps the speed of the wheels within their operating margins using a combination of solar torque and the RCS.