Engineering topics
Publications and source records attributed to Ortiz, M..
We present new CMOS photodiode imager pixel with ultra-low read noise through on-chip suppression of reset noise via column-based feedback circuitry. The noise reduction is achieved without introducing any image lag, and with insignificant reduction in quantum efficiency and full well.
This paper discusses common approaches to CMOS APS technology, as well as specific results on the five-wire programmable digital camera-on-a-chip developed at JPL. The paper also reports recent research in the design, operation, and performance of APS imagers for several imager applications.
This paper presents a new technique for implementing a low-power CMOS imager with simultaneous on-chip computation of the difference and summ of two successive frames.
This paper presents a new technique for implementing a low-power CMOS imager with simultaneous on-chip computation of the difference and sum of two successive frames.
Low-power, low-cost, miniature and integrated digital imaging systems are expected to be widely used in consumer electronics in the near future. While CMOS technology has been responsible for the phenomenal growth in consumer electronics, micro-porcessors, memory, audio systems, and radio-frequency circuits (e.g. cellular phones), till recently, the video technology remained outside this mainstream.
Explore the source record for details and available documents.
For more than three decades now, CMOS technology has been the backbone behind the phenomenal advances in low-cost, low-power, reliable, highly integrated and miniaturized system development.
JPL, under sponsorship from the NASA Office of Advanced Concepts and Technology, has been developing a second-generation solid-state image sensor technology. Charge-coupled devices (CCD) are a well-established first generation image sensor technology. For both commercial and NASA applications, CCDs have numerous shortcomings. In response, the active pixel sensor (APS) technology has been under research. The major advantages of APS technology are the ability to integrate on-chip timing, control, signal-processing and analog-to-digital converter functions, reduced sensitivity to radiation effects, low power operation, and random access readout.
This paper describes ongoing research and development of CMOS active pixel image sensors for low cost commercial applications. A number of sensor designs have been fabricated and tested in both p-well and n-well technologies. Major elements in the development of the sensor include on-chip analog signal processing circuits for the reduction of fixed pattern noise, on-chip timing and control circuits and on-chip analog-to-digital conversion (ADC). Recent results and continuing efforts in these areas will be presented.
The performance of group implicit algorithms is assessed on actual concurrent computers. It is shown that, as the number of subdomains is increased, performance enhancements are derived from two sources: the increased parallelism in the computations; and a reduction in equation solving effort. Moreover, these two performance enhancements are synergistic, in the sense that the corresponding speed-ups are multiplied, rather than merely added. Simulations on a 32-node hypercube are presented for which the interprocessor communications efficiencies obtained are consistently in excess of 90 percent.
During the 70's and 80's, considerable effort was devoted to developing efficient and reliable time stepping procedures for transient structural analysis. Mathematically, the equations governing this type of problems are generally stiff, i.e., they exhibit a wide spectrum in the linear range. The algorithms best suited to this type of applications are those which accurately integrate the low frequency content of the response without necessitating the resolution of the high frequency modes. This means that the algorithms must be unconditionally stable, which in turn rules out explicit integration. The most exciting possibility in the algorithms development area in recent years has been the advent of parallel computers with multiprocessing capabilities. So, this work is mainly concerned with the development of parallel algorithms in the area of structural dynamics. A primary objective is to devise unconditionally stable and accurate time stepping procedures which lend themselves to an efficient implementation in concurrent machines. Some features of the new computer architecture are summarized. A brief survey of current efforts in the area is presented. A new class of concurrent procedures, or Group Implicit algorithms is introduced and analyzed. The numerical simulation shows that GI algorithms hold considerable promise for application in coarse grain as well as medium grain parallel computers.
Information on concurrent algorithms for transient finite element analysis is given in viewgraph form. Information is given on concurrent dynamic algorithms, interprocessor communication, the performance of the BAR problem on the 32 Processor Hypercube, computational efficiency and accuracy analysis.
A life prediction model for correlating the spallation life of ceramic thermal barrier coatings is developed which includes both cyclic and time-dependent damage. The cyclic damage is related to the calculated cyclic inelastic strain range, while the time-dependent damage is related to the oxidation kinetics at the bond-ceramic interface. The cyclic inelastic strain range is calculated using a modified form of the Walker viscoplastic material model; calculation of the oxidation kinetics is based on traditional oxidation algorithms using experimentally determined parameters. The correlation between the actual and predicted spallation lives is within a factor of 3.
The objectives of this program are to increase understanding of thermal barrier coating (TBC) degradation and failure modes, to generate quantitative ceramic failure life data under cyclic thermal conditions which simulate those encountered in gas turbine engine service, and to develop an analytical methodology for prediction of coating life in the engine. Observations of degradation and failure modes in plasma deposited ceramic indicate that spallation failure results from progressive cracking of the ceramic parallel to and adjacent to, but not coincident with the metal-ceramic interface.
A two-parameter class of time-stepping algorithms for nonlinear structural dynamics is investigated. What sets the present method apart from other concurrent algorithms is the fact that it can be used to some advantage in sequential machines as well. Thus, substantial speed-ups are obtained on a single processor as the number of subdomains is increased. An additional O(p) speed-up is obtained when p processors are utilized. The test case discussed is being repeated for a mesh comprising four times as many elements, in an effort to understand how the large scale asymptotic speed-ups are attained. A three dimensional example involving finite deformations and free body motions is also being pursued. A code optimized for concurrency in the Alliant FX8 computer is being finalized. This will provide the means for testing the performance of the algorithm in a multiprocessor environment.
The spatial formulation of the elastoplastic dynamic problem for finite deformations is considered. A thermodynamic argument leads to an additive decomposition of the spatial rate of deformation tensor and allows an operator split of the evolutionary equations of the problem into elastic and plastic parts. This operator split is taken as the basis for the definition of a global product algorithm. In the context of finite element discretization the product algorithm entails, for every time step, the solution of a nonlinear elastodynamic problem followed by the application of plastic algorithms that operate on the stresses and internal variables at the integration points and bring in the plastic constitutive equations. Suitable plastic algorithms are discussed for the cases of perfect and hardening plasticity and viscoplasticity. The proposed formalism does not depend on any notion of smoothness of the yield surface and is applicable to arbitrary convex elastic regions, with or without corners. The stabiity properties of the global product algorithm are shown to be identical to those of the algorithm used for the integration of the nonlinear elastodynamic problem. Numerical examples illustrate the accuracy of the method.