Engineering topics

Osborne, T. H.

Publications and source records attributed to Osborne, T. H..

At least 19 records

DOE OSTI2025

Turbulence suppression at extreme plasma densities on DIII-D and EAST

Recent high-poloidal-beta (high-βP) experiments on DIII-D and EAST have made coordinated breakthroughs for high confinement quality at high density near the Greenwald limit. Density gradient amplification of turbulence suppression at high βP can explain both of these achievements. Experiments on DIII-D have achieved Greenwald fraction (fGr = line-averaged density/Greenwald density) above 1 simultaneously with normalized energy confinement (H98y2) around 1.5, as required in fusion reactor designs but never before verified in tokamak experiments with the divertor configuration. A synergy between increased H98y2 and fGr is observed with strong gas puffing, due to the build-up of an internal transport barrier at large radius in the temperature and density channels. Transport simulations reveal that the favorable trend of reduced turbulent energy transport at higher density is only expected when increasing the density gradient at high local safety factor and high β, thus at high βP to ensure strong α-stabilization. These conditions are crucial to many conceptual designs for steady-state reactors. New experiments on EAST have nearly doubled the ion temperature at fGr ∼ 0.9, consistent with predict-first modeling results based on the same physics revealed from the DIII-D analysis. All previous EAST long-pulse H-modes have Ti ≪ Te near plasma axis. Transport modeling indicates that the profiles are limited by ion-temperature-gradient modes at mid-radius. The modeling also suggested potential solutions, including reducing magnetic shear, enhancing density gradients, and higher impurity concentration. Following this guidance, EAST experiments directly show a strong enhancement of Ti achieved with a combination of a second plasma current ramp-up, a density gradient increase, and a Zeff perturbation by a short pulse (100 ms) of impurity injection, as predicted by the earlier modeling.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2024

The role of ion-scale micro-turbulence in pedestal width of the DIII-D wide-pedestal QH mode

The low-edge rotation, intrinsically ELM-free, and improved confinement wide-pedestal quiescent H-mode (QH-mode), discovered in DIII-D tokamak, has pedestal widths exceeding the EPED-kinetic-ballooning mode (KBM) model scaling typically by at least 25%. Ion-scale ($k_yp_s$ < 1) microturbulence and its role in setting the pedestal structure is investigated using the radially local δ$f$ gyrokinetic code CGYRO. The electromagnetic trapped electron mode (TEM) is unstable at the pedestal top, while plasma beta (β$_e$) is ∼60% below the KBM onset threshold and the electron temperature gradient mode is found to be unstable in the peak gradient region. Nonlinear simulation reveals that the ion-scale turbulence could produce electron energy flux consistent with the flux inferred from power balance at the pedestal top, with a reasonable variation of the local shearing rate; and the local neoclassical transport from NEO is dominant over the simulated turbulent transport in the ion energy flux channel. The simulated ion-scale turbulence produces much lower electron energy flux than inferred from experiment in the pedestal peak gradient region. A correction to the EPED-KBM pedestal width scaling is obtained based on the two-dimensional scan of pedestal top plasma beta (β$_e$) and normalized electron density and temperature scale lengths,${a}$/${L_n}_e$, ${a}$/${L_T}_n$using CGYRO linear simulations. Mode transitions among TEM, micro-tearing mode, ion-temperature gradient mode and KBM, are observed in the 2D scan at the pedestal top. A fixed normalized growth rate for these drift-type modes is taken to determine the pedestal width scaling, which shows good consistency with the QH experimental database on pedestal heights and widths. The onset of KBM instabilities and the local E × B shear suppression criterion set the lower and upper limit for the pedestal width of standard QH-mode, wide-pedestal QH-mode and type-I ELMy H mode. A potentially higher and wider pedestal is expected from the new scaling of pedestal width. This work presents an improved understanding of the ion-scale micro-turbulence of wide-pedestal QH-mode and sheds light on a promising scenario for future reactors, including ITER and beyond.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2024

ELM-free H-mode phase and decoupling of peeling–ballooning stability boundary in the MAST Upgrade tokamak

A linear magnetohydrodynamic (MHD) peeling–ballooning stability analysis of the edge-localized mode (ELM)-free phase of a MAST Upgrade (MAST-U) H-mode plasma is presented. In contrast to other similar discharges, #47018 is found to have a significantly higher and wider pedestal during its ELM-free H-mode phase that lasts for approximately 80 ms; this is made possible by the reduced core MHD mode activity on the q = 2 surface. During this period, there is sustained decoupling of peeling and ballooning branches of the stability boundary on J–α space, opening an access channel to the second stability regime with higher peaks in pedestal current density $J_{\mathrm{N,ped}}$ and pressure gradient (α). Such decoupling of the stability boundary has not previously been observed in MAST-U H-modes, and if such a condition can be readily reproduced, it opens a wide range of opportunities for MAST-U to explore low-collisionality peeling-limited pedestal regimes as well as advanced scenarios such as quiescent H-modes that are relevant to future reactors such as STEP and ITER.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2024

Effect of rotation on negative triangularity plasmas in DIII-D

At the DIII-D tokamak, plasmas with negative triangularity (NT) have been found to have similar energy confinement times as H-mode plasmas with positive triangularity. These NT plasmas also have a stable edge that inhibits H-mode, lacks dangerous edge transients, and has naturally low impurity confinement. For these reasons, NT plasmas have the potential to be a transformative reactor scenario. To determine the importance of strong co-current neutral beam torque for NT performance at DIII-D, scans of neutral beam torque at constant neutral beam power have been performed. These scans have shown that the energy confinement time for a basic, inductive NT scenario (q 95 ≈ 2.8) decreases by 16% when torque is reduced to reactor levels. This reduction in confinement can be replicated with gyrofluid modeling that isolates the role of E x B shear in the change in transport. In a separate set of discharges with lower plasma current (q 95 ≈ 2.5), no significant correlation between confinement time and rotation was found. Throughout this investigation, excellent MHD stability was observed, even with very low toroidal rotation. Further, low impurity confinement was found at multiple rotation levels. Throughout the campaign, rotation near the edge was counter-current, consistent with the measurement of counter-current intrinsic edge rotation, and these observations agree with NT results from the TCV tokamak.

confinement↗

DOE OSTI2024

Simultaneous access to high normalized density, current, pressure, and confinement in strongly-shaped diverted negative triangularity plasmas

Strongly-shaped diverted negative triangularity (NT) plasmas in the DIII-D tokamak demonstrate simultaneous access to high normalized density, current, pressure, and confinement. NT plasmas are shown to exist across an expansive parameter space compatible with high fusion power production, revealing surprisingly good core stability properties that compare favorably to conventional positive triangularity plasmas in DIII-D. Non-dimensionalizing the key parameters, expanded operating spaces featuring edge safety factors below 3, normalized betas above 3, Greenwald density fractions above 1, and high-confinement mode (H-mode) confinement qualities above 1 are observed, even simultaneously, and all with a robustly stable edge free from deleterious edge-localized mode instabilities. Scaling of the confinement time with engineering parameters reveals at least a linear dependence on plasma current although with significant power degradation, both in excess of expected H-mode scalings. These results increase confidence that NT plasmas are a viable approach to realize fusion power and open directions for future detailed study.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2024

Compatibility of divertor detachment and ELM suppression in DIII-D high- β p plasmas with ITER-similar shape

Abstract Integration of transient and steady-state divertor heat fluxes control with a high-performance core is necessary for future fusion reactors. In recent DIII-D high- β p experiments, divertor detachment and simultaneous edge localized mode (ELM) suppression are demonstrated while the plasma confinement quality is maintained high in ITER-similar shape. By optimizing the neon injection in high- β p scenario with ITER-similar shape, deep detachment and ELM suppression are achieved with a high-performance core ( β N ∼ 2.8, β p ∼ 2.3) at q 95 ∼ 7.5. Partial divertor detachment and suppression of large ELMs are achieved at q 95 ∼ 6. The stability analyses suggest that with low neon injection, the density pedestal becomes higher and steeper and the T i profile also increases, therefore the increased edge pressure and higher current density destabilize the Peeling-Ballooning mode (PBM), which would lead to a large ELM collapse. With strong neon gas puffing, the significantly reduced pedestal pressure and current density, due to the degraded T e pedestal, lead to the stabilization of PBM and ELMs are suppressed. For both cases, the coupling between the large radius internal transport barrier (ITB) and edge pedestal is the key reason for maintaining high global performance. The formation of large radius ITB compensates for pedestal degradation. Such results could provide an attractive scenario to well control the transient and steady-state heat flux onto the divertor plates while maintaining good plasma performance, which is an important step toward the steady-state operation of future fusion reactors.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2024

Observation of a new pedestal stability regime in MAST Upgrade H-mode plasmas

Abstract The first pedestal stability and structure analysis on the new MAST Upgrade (MAST-U) spherical tokamak H-mode plasmas is presented. Our results indicate that MAST-U pedestals are close to the low toroidal mode number ( n ) peeling branch of the peeling-ballooning instability, in contrast with MAST H-mode pedestals which were deeply in the high- n ballooning branch. This offers the possibility of reaching the ELM-free quiescent H-mode (Burrell et al 2005 Plasma Phys. Control. Fusion 47 B37–B52) or high-performance super H-mode (Snyder et al 2015 Nucl. Fusion 55 083026; Snyder et al 2019 Nucl. Fusion 59 086017) regimes. In addition, the coupling between the peeling and ballooning branches is weak in MAST-U, suggesting that a path to very high pedestal pressure gradient at high density may exist with sufficient heating power. A possible explanation for the differences between MAST and MAST-U pedestal stability is given in terms of plasma shaping parameters, in particular squareness and elongation, as well as the pedestal top temperature and collisionality.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2024

A high-density and high-confinement tokamak plasma regime for fusion energy

The tokamak approach, utilizing a toroidal magnetic field configuration to confine a hot plasma, is one of the most promising designs for developing reactors that can exploit nuclear fusion to generate electrical energy. To reach the goal of an economical reactor, most tokamak reactor designs simultaneously require reaching a plasma line-averaged density above an empirical limit—the so-called Greenwald density and attaining an energy confinement quality better than the standard high-confinement mode. However, such an operating regime has never been verified in experiments. In addition, a long-standing challenge in the high-confinement mode has been the compatibility between a high-performance core and avoiding large, transient edge perturbations that can cause very high heat loads on the plasma-facing-components in tokamaks. Here we report the demonstration of stable tokamak plasmas with a line-averaged density approximately 20% above the Greenwald density and an energy confinement quality of approximately 50% better than the standard high-confinement mode, which was realized by taking advantage of the enhanced suppression of turbulent transport granted by high density-gradients in the high-poloidal-beta scenario. Furthermore, our experimental results show an integration of very low edge transient perturbations with the high normalized density and confinement core. The operating regime we report supports some critical requirements in many fusion reactor designs all over the world and opens a potential avenue to an operating point for producing economically attractive fusion energy.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2024

The role of isotope mass on neutral fueling and density pedestal structure in the DIII-D tokamak

Abstract Experimental measurements on DIII-D of hydrogen neutral penetration lengths ( λ n 0 ) on the high field side (HFS) are longer by a factor of 2 than for deuterium consistent with the thermal velocity ratio for neutrals at the same temperature ( v t h H / v t h D = 2 ) . This ratio is constant for both low and high pedestal electron density. At low pedestal density ( n e ∼ 4 × 10 19 m − 3 ) , the neutral penetration length is greater than the density pedestal width for both isotopes, and the additional 40% increase of neutral penetration in hydrogen widens the pedestal by the same amount. As the density pedestal height increases ( n e ∼ 6 × 10 19 m − 3 ) , the neutral penetration lengths drop below the density pedestal widths for both isotopes, and the increased penetration of hydrogen has no increased effect on the pedestal width compared to deuterium. Extrapolating to future reactor-relevant high electron density pedestals, the isotope-mass change in neutral fueling on the HFS from the deepest neutral penetration of hydrogen, to the shortest neutral penetration of tritium will be negligible (0.2–0.4 cm) in comparison to estimates of the density pedestal width (6–8.5 cm).

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2023

Direct measurement of the electron turbulence-broadening edge transport barrier to facilitate core–edge integration in tokamak fusion plasmas

Abstract The integration of a high-performance core and a dissipative divertor, or the so-called ‘core–edge integration,’ has been widely identified as a critical gap in the design of future fusion reactors. In this letter, we report, for the first time, direct experimental evidence of electron turbulence at the DIII-D H-mode pedestal that correlates with the broadening of the pedestal and thus facilitates core–edge integration. In agreement with gyrokinetic simulations, this electron turbulence is enhanced by high η e ( η e = L n / L T e , where L n is the density scale length and L T e is the electron temperature scale length), which is due to a strong shift between the density and temperature pedestal profiles associated with a closed divertor. The modeled turbulence drives significant heat transport with a lower pressure gradient that may broaden the pedestal to a greater degree than the empirical and theoretically predicted pedestal width scalings. Such a wide pedestal, coupled with a closed divertor, enables us to achieve a good core–edge scenario that integrates a high-temperature low-collisionality pedestal (pedestal top temperature T e,ped > 0.8 keV and a pedestal top collisionality ν * ped < 1) under detached divertor conditions. This paves a new path toward solving the core–edge integration issue in future fusion reactors.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2023

Comparison of MHD stability properties between QH-mode and ELMy H-mode plasmas by considering plasma rotation and ion diamagnetic drift effects

Magnetohydrodynamic (MHD) stability at tokamak edge pedestal in a quiescent H-mode (QH-mode) and type-I ELMy H-mode plasmas in DIII-D experiment was analyzed by considering plasma rotation and ion diamagnetic drift effects. QH-mode plasma is marginally stable to kink/peeling mode (K/PM), but ELMy H-mode one is almost unstable to peeling-ballooning mode (PBM). It was identified that there are three physics features responsible for the difference in the MHD stability properties between QH-mode plasma and ELMy H-mode one. These are the distance of pedestal foot from the last closed flux surface (LCFS), the amount of the ion diamagnetic drift frequency at pedestal, and impact of coupled rotation and ion diamagnetic drift effects. These features were confirmed through the numerical experiments that the stability properties of the QH-mode plasma can be changed to that of the ELMy H-mode one by shifting the plasma profiles inward in the radial direction and halving the ion diamagnetic drift frequency. The reasons of the change in the stability properties are thought as that K/PM is stabilized due to the inward shift of the bootstrap current profile, and PBM is destabilized due to the reduction of the coupled rotation and ion diamagnetic drift stabilizing effect. Importance of these features was validated through numerical experiments with experimental data of other QH-mode plasmas in DIII-D. All the results show that MHD stability properties of QH-mode plasma can be obtained in case that pedestal foot is close to LCFS, ion diamagnetic drift frequency is large due to high ion temperature, and strong rotation shear exists near pedestal.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2023

Study on divertor detachment and pedestal characteristics in the DIII-D upper closed divertor

Abstract Experiments performed in DIII-D demonstrate that higher plasma current and heating power combined with impurity seeding facilitate the achievement of divertor detachment with a higher pedestal pressure and higher plasma performance in H-mode plasmas with a baffled closed divertor compared with an open divertor. Dedicated experiments were carried out to study the impact of power, plasma current and impurity seeding on divertor detachment with ion B × ∇ B directed into the divertor favorable for the L–H transition. With a factor of three variation in heating power and with only D 2 puffing, no significant difference in the separatrix density at detachment onset was found. The higher heating power leads to higher impurity concentration and wider scrape-off layer (SOL) width, and reduces the detachment onset density to one similar to that in lower-power plasmas. Higher current requires higher pedestal and line-averaged densities to achieve divertor detachment; however, the increase in separatrix density at increasing plasma current is found to be less pronounced. Initial calculations found that both power scan and plasma current scan datasets are qualitatively consistent with theory after considering the change in impurity concentration and heat flux width. This also motivates the future extensive study of transport and divertor impurity behavior in order to have a quantitative comparison between experiment and theory. Compared with an open divertor, a closed divertor facilitates detachment onset at ∼40% lower line-averaged plasma density. Additional N 2 seeding facilitates the achievement of detachment at a lower separatrix density and thus a higher pedestal temperature, which is beneficial for advanced tokamak scenarios. Higher heating power requires a higher N 2 puffing rate to achieve the same degree of detachment, while a higher N 2 puffing rate leads to lower detachment onset line-averaged density, both of which agree with theory. In contrast to the narrower pedestal in an open divertor approaching detachment, the pedestal density width in a closed divertor increases with density. The density gradient increases with line-averaged density at higher plasma current, but remains nearly unchanged at lower plasma current. In particular, compared with discharges with low power, at high heating power the pedestal density gradient is much weaker, while the SOL density is significantly higher and wider. At the same plasma current, both pedestal pressure gradient and temperature gradient decrease linearly with the line-averaged density but remain similar across different heating powers. Even with different plasma current and heating power, the normalized pressure gradient remains identical. As a result, achievement of divertor detachment with a higher pedestal pressure and higher plasma performance is shown in a closed divertor, which is important for improving core–edge integration as one of the critical issues for future tokamak fusion reactors.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2022

Local measurements of the pedestal magnetic field profile throughout the ELM cycle on DIII-D

We report new high speed localized measurements of the pedestal magnetic field during the edge localized mode (ELM) cycle of a DIII-D High confinement mode (H-mode) discharge indicate a temporally and spatial complex redistribution of the edge current density profile, $j_{edge}$. The measurement technique extracts the magnetic field magnitude, $\textit{B}$, via the spectral separation of Stark-split neutral beam radiation in the pedestal. Single spatial channel measurements from a novel spatial heterodyne spectrometer are validated in discharges with core current profile changes. The technique measures Stark-splitting changes that imply $\textit{B}$ changes as small as 1 mT with high time resolution (50 μs). At normalized poloidal flux $ψ_n$ = 1.0, $\textit{B}$ appears saturated in the inter-ELM period and then rapidly decreases in <200 μs by ~1%, before edge recycling emission begins to increase. Radially inboard of $j_{edge}$, $\textit{B}$ increases at the ELM crash. The behavior is consistent with a rapid collapse of $j_{edge}$ at the ELM crash and subsequent pedestal recovery. In some discharges, at $ψ_n$ < 0.96, changes in $\textit{B}$ are observed throughout the ELM cycle. In others, $\textit{B}$ recovers and is relatively stable until a few ms leading up to the next crash. Measurements of $\textit{B}$ during the H-mode transition show a large increase at $ψ_n$ = 1 with little change at $ψ_n$ = 0.9, consistent with the formation of the edge bootstrap current density peak. The $ψ_n$ = 0.9 spectrum is complicated by predicted changes to the Stark component intensities with density at the L–H transition.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2022

Numerical modeling of pedestal stability and broadband turbulence of wide-pedestal QH-mode plasmas on DIII-D

The wide-pedestal quiescent high confinement mode discovered on DIII-D in recent years is a stationary and quiescent H-mode (QH-mode) with the pedestal width exceeding EPED prediction by at least 25%. Its characteristics, such as low rotation, high energy confinement and edge localized mode-free operation, make it an attractive operation mode for future reactors. Linear and nonlinear simulations using BOUT++ reduced two fluid MHD models and awere carried out to investigate the bursty broadband turbulence often observed in the edge of wide-pedestal QH-mode plasmas. Two kinds of MHD-scale instabilities in different spatial locations within the pedestal were found in the simulations: one mild peeling–ballooning (PB) mode γ PB < 0.04ω A ) located near the minimum in E r</:sub> well propagating in ion diamagnetic drift direction; and one drift-Alfvén wave locates at smaller radius compared to E r</:sub> well propagating in the electron diamagnetic drift direction and unstable only when the parallel electron dynamics is included in the simulation. The coupling between drift wave and shear Alfvén wave provides a possible cause of the experimentally observed local profile flattening in the upper-pedestal. The rotation direction, mode location, as well as the wavenumber of these two modes from BOUT++ simulations agree reasonably well with the experimental measurements, while the lack of quantitative agreement is likely due to the lack of trapped electron physics in current fluid model. This work presents improved physics understanding of the pedestal stability and turbulence dynamics for wide-pedestal QH-mode.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2021

Inter-ELM pedestal evolution and the role of edge fluctuations in the C-Mod and DIII-D tokamaks

Edge localized modes (ELMs) lead to a cyclical behaviour of the H-mode pedestal density, temperature and pressure. Substantial evidence exists associating the ELM crash with violation of ideal MHD stability, via current driven kink/peeling modes and/or pressure gradient driven ballooning modes. Recovery from ELM crashes and buildup to the next ELM crash is an active and critical area of edge physics research for ITER projections. In one set of theories, the pedestal pressure profile in H-mode discharges is predicted to be limited by micro-instabilities. One such micro-instability is the kinetic ballooning mode (KBM), which is hypothesized to provide a ‘soft’ limit that regulates the edge transport, thereby restricting the local pressure gradient. In this picture, e.g. in the EPED model, the pedestal width expands slowly until the ideal MHD stability limit is reached. Experiments were recently performed on the C-Mod and DIII-D devices to search for instabilities correlated with the pedestal evolution between ELMs. The results show correlations between the onset of quasi-coherent fluctuations between type I ELMs and a critical temperature gradient. Linear gyrokinetic calculations have shown that these fluctuations have characteristics similar to those expected for KBMs. These results provide additional data toward validation of the EPED model, increasing confidence in ITER projections.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2021

High fusion performance in Super H-mode experiments on Alcator C-Mod and DIII-D

The ‘Super H-Mode’ regime is predicted to enable pedestal height and fusion performance substantially higher than standard H-Mode operation. This regime exists due to a bifurcation of the pedestal pressure, as a function of density, that is predicted by the EPED model to occur in strongly shaped plasmas above a critical pedestal density. Experiments on Alcator C-Mod and DIII-D have achieved access to the Super H-Mode (and Near Super H) regime, and obtained very high pedestal pressure, including the highest achieved on a tokamak (pped ~ 80 kPa) in C-Mod experiments operating near the ITER magnetic field. DIII-D Super H experiments have demonstrated strong performance, including the highest stored energy in the present configuration of DIII-D (W ~ 2.2–3.2 MJ), while utilizing only about half of the available heating power (Pheat ~ 7–12 MW). These DIII-D experiments have obtained the highest value of peak fusion gain, QDT,equiv ~ 0.5, achieved on a medium scale (R < 2 m) tokamak. Sustained high performance operation (βN ~ 2.9, H98 ~ 1.6) has been achieved utilizing n = 3 magnetic perturbations for density and impurity control. Pedestal and global confinement has been maintained in the presence of deuterium and nitrogen gas puffing, which enables a more radiative divertor condition. A pair of simple performance metrics is developed to assess and compare regimes. Super H-Mode access is predicted for ITER and expected, based on both theoretical prediction and observed normalized performance, to allow ITER to achieve its goals (Q = 10) at Ip < 15 MA, and to potentially enable more compact, cost effective pilot plant and reactor designs.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2021

Observation of fully detached divertor integrated with improved core confinement for tokamak fusion plasmas

Integration of divertor detachment with a high-performance (β N ~ 3, β p > 2, H 98 ~ 1.5) core plasma has been demonstrated in DIII-D high-β p (poloidal beta) plasmas associated with a sustained core internal transport barrier (ITB) and an H-mode edge transport barrier (ETB). Such good core-edge integration has been achieved for both neon and nitrogen seeding, for both favorable and unfavorable B-field directions, independently from the impurity puffing locations, though these variations play important roles on divertor characteristics. Compared to the standard H-mode plasmas, the high-β p plasma exhibits a much wider window of detachment compatible with high confinement core. Fully detached divertor plasmas with low plasma temperature (Te < 5 eV), low particle flux, and low heat flux across the entire divertor target plate were obtained by using nitrogen seeding. This detached high-β p plasma is compatible with a newly developed detachment control system which can help optimize the nitrogen gas flow rate. Several features, i.e., the high edge safety factor in the high-β p scenario, impurity injection, closed divertor and reduced heating power requirement due to the high confinement, facilitate the achievement of full divertor detachment at lower density. Instead of degrading global performance, the divertor detachment facilitates the access to an even stronger ITB at large radius with a relatively weak ETB through self-organized synergy between ITB and ETB, leading to sustained high confinement. The strengthening of the large-radius ITB compensates for the ETB degradation associated with divertor detachment. In addition, a weak ETB naturally has smaller edge localized modes (ELMs). In particular, with neon injection, a long-period no-ELM H-mode phase has been achieved simultaneously with high-performance core and partially detached divertor plasmas. Furthermore, these results demonstrate the possibility of integrating excellent core plasma performance with an effective divertor solution, an essential step toward steady-state operation of reactor-grade plasmas.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2020

Grassy ELM regime at low pedestal collisionality in high-power tokamak plasma

Spontaneous mitigation of giant ELMs and appearance of grassy ELMs have been observed repeatedly at low pedestal collisionality (${\nu }_{\mathrm{e},\mathrm{p}\mathrm{e}\mathrm{d}}^{{\ast}}\sim 0.15$) in the high-power (P inj > 13 MW) hybrid scenario in DIII-D. Higher β p and higher q 95 appear to be beneficial to achieving the grassy ELM regime. The grassy ELM H-mode plasma shows high energy confinement performance (H 98y2 up to over 1.5) under the conditions of high neutral beam torque and high core rotation. The pedestal width appears to exceed the EPED1.0 model prediction by more than 50%. Pedestal stability analysis performed with the ELITE code indicates that the stability against low-n kink/peeling modes is improved with increased auxiliary heating power and the operational point in the grassy ELM regime is located near the ballooning boundary. The pedestal stability characteristics during the grassy ELM crashes have been investigated in comparison with the giant ELM crashes based on plasma profiles experimentally measured with high resolution and accuracy. It has been found that the underlying mechanism for the observed small-amplitude ELM crashes is mainly the expansion of the ballooning stability boundary induced by an initial radially localized collapse in the pedestal, which helps to stop the growth of instabilities and further collapse of the pedestal. The effect of electron density pedestal on mitigating edge localized instabilities has been analyzed by numerical simulation, suggesting that the electron density pedestal characterized by high n e,sep /n e,ped and low density gradient helps to stabilize peeling-ballooning modes because of a low pressure pedestal gradient and to lower the ballooning boundary mainly because of a low ion diamagnetic frequency in the pedestal region, thus triggering ballooning instabilities and producing the intrinsic grassy ELMs. Numerical simulation of the Chinese fusion engineering test reactor (CFETR) with the SOLPS code indicates that the separatrix density might be insensitive to the electron diffusivity in the pedestal region and increase with the power flowing from the core region to the edge region. Furthermore, pedestal stability analysis suggests that the flat density pedestal with high separatrix density obtained in the high-power plasma in CFETR would make the operational point close to the ballooning boundary, which is considered to help destabilize ballooning instabilities and facilitate the access to the grassy ELM regime.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗