Engineering topics

Oswald, Fred B.

Publications and source records attributed to Oswald, Fred B..

At least 37 records · Page 2

NASA NTRS2002

Space Mechanisms Technology Workshop

The Mechanical Components Branch at NASA Glenn Research Center hosted a workshop on Tuesday, May 14, 2002, to discuss space mechanisms technology. The theme for this workshop was 'Working in the Cold,' a focus on space mechanisms that must operate at low temperatures. We define 'cold' as below -60C (210 K), such as would be found near the equator of Mars. However, we are also concerned with much colder temperatures such as in permanently dark craters of the Moon (about 40 K).

Oswald, Fred B.↗

NASA NTRS2002

Candidate Coatings and Dry Traction Drives for Planetary Vehicles

Robert Fusaro and Fred Oswald of the Mechanical Components Branch discussed 'Candidate Coatings and Dry Traction Drives for Planetary Vehicles'. Vehicles to be designed for exploration of planets and moons of the solar system will require reliable mechanical drives to operate efficiently. Long-term operation of these drives will be challenging because of extreme operating conditions. These extreme conditions include: very high and/or very cold temperatures, wide temperature ranges, dust, vacuum or low-pressure atmospheres, and corrosive environments. Most drives used on Earth involve oil-lubricated gears. However, due to the extreme conditions on planetary surfaces, it may not be advisable or even possible to use oil lubrication. Unfortunately, solid lubricants do not work well when applied to gears because of the high contact stress conditions and large sliding motion between the teeth, which cause wear and limit life. We believe traction drives will provide an attractive alternative to gear drives. Traction drives are composed of rollers that provide geometry more conducive to solid lubrication. Minimal slip occurs in this contact geometry and thus there is very low wear to the solid lubricant. The challenge for these solid-lubricated drives is finding materials or coatings that provide the required long-life while also providing high traction. We seek materials that provide low wear with high friction.

Fusaro, Robert↗

NASA NTRS2002

Proceedings of the 36th Aerospace Mechanisms Symposium

The Aerospace Mechanisms Symposium (AMS) provides a unique forum for those active in the design, production, and use of aerospace mechanisms. A major focus is the reporting of problems and solutions associated with the development and flight certification of new mechanisms. Organized by the Mechanisms Education Association, the National Aeronautics and Space Administration and Lockheed Martin Space Systems Company (LMSSC) share the responsibility for hosting the AMS. Now in its 36th year, the AMS continues to be well attended, attracting participants from both the United States and abroad. The 36th AMS, hosted by the Glenn Research Center (GRC) in Cleveland, Ohio, was held May 15, 16, and 17, 2002. During these three days, 32 papers were presented. Topics included deployment mechanisms, tribology, actuators, pointing and optical mechanisms, International Space Station mechanisms, release mechanisms, and test equipment. Hardware displays during the supplier exhibit gave attendees an opportunity to meet with developers of current and future mechanism components.

Boesiger, Edward A.↗

NASA NTRS2002

Gear Transmission Error Measurement System Made Operational

A system directly measuring the transmission error between the meshing spur or helical gears was installed at the NASA Glenn Research Center and made operational in August 2001. This system employs light beams directed by lenses and prisms through gratings mounted on the two gear shafts. The amount of light that passes through both gratings is directly proportional to the transmission error of the gears. The device is capable of resolution better than 0.1 mm (one thousandth the thickness of a human hair). The measured transmission error can be displayed in a "map" that shows how the transmission error varies with the gear rotation or it can be converted to spectra to show the components at the meshing frequencies. Accurate transmission error data will help researchers better understand the mechanisms that cause gear noise and vibration and will lead to The Design Unit at the University of Newcastle in England specifically designed the new system for NASA. It is the only device in the United States that can measure dynamic transmission error at high rotational speeds. The new system will be used to develop new techniques to reduce dynamic transmission error along with the resulting noise and vibration of aeronautical transmissions.

Oswald, Fred B.↗

NASA NTRS2001

Space Mechanisms Technology Workshop

The Mechanical Components Branch at NASA Glenn Research Center hosted a workshop to discuss the state of drive systems technology needed for space exploration. The Workshop was held Thursday, November 2, 2000. About 70 space mechanisms experts shared their experiences from working in this field and considered technology development that will be needed to support future space exploration in the next 10 to 30 years.

Oswald, Fred B.↗

NASA NTRS2001

New Gear Transmission Error Measurement System Designed

The prime source of vibration and noise in a gear system is the transmission error between the meshing gears. Transmission error is caused by manufacturing inaccuracy, mounting errors, and elastic deflections under load. Gear designers often attempt to compensate for transmission error by modifying gear teeth. This is done traditionally by a rough "rule of thumb" or more recently under the guidance of an analytical code. In order for a designer to have confidence in a code, the code must be validated through experiment. NASA Glenn Research Center contracted with the Design Unit of the University of Newcastle in England for a system to measure the transmission error of spur and helical test gears in the NASA Gear Noise Rig. The new system measures transmission error optically by means of light beams directed by lenses and prisms through gratings mounted on the gear shafts. The amount of light that passes through both gratings is directly proportional to the transmission error of the gears. A photodetector circuit converts the light to an analog electrical signal. To increase accuracy and reduce "noise" due to transverse vibration, there are parallel light paths at the top and bottom of the gears. The two signals are subtracted via differential amplifiers in the electronics package. The output of the system is 40 mV/mm, giving a resolution in the time domain of better than 0.1 mm, and discrimination in the frequency domain of better than 0.01 mm. The new system will be used to validate gear analytical codes and to investigate mechanisms that produce vibration and noise in parallel axis gears.

Oswald, Fred B.↗

NASA NTRS2000

Influence of Tooth Spacing Error on Gears With and Without Profile Modifications

A computer simulation was conducted to investigate the effectiveness of profile modification for reducing dynamic loads in gears with different tooth spacing errors. The simulation examined varying amplitudes of spacing error and differences in the span of teeth over which the error occurs. The modification considered included both linear and parabolic tip relief. The analysis considered spacing error that varies around most of the gear circumference (similar to a typical sinusoidal error pattern) as well as a shorter span of spacing errors that occurs on only a few teeth. The dynamic analysis was performed using a revised version of a NASA gear dynamics code, modified to add tooth spacing errors to the analysis. Results obtained from the investigation show that linear tip relief is more effective in reducing dynamic loads on gears with small spacing errors but parabolic tip relief becomes more effective as the amplitude of spacing error increases. In addition, the parabolic modification is more effective for the more severe error case where the error is spread over a longer span of teeth. The findings of this study can be used to design robust tooth profile modification for improving dynamic performance of gear sets with different tooth spacing errors.

Padmasolala, Giri↗

NASA NTRS1996

Balancing Dynamic Strength of Spur Gears Operated at Extended Center Distance

This paper presents an analytical study on using hob offset to balance the dynamic tooth strength of spur gears operated at a center distance greater than the standard value. This study is an extension of a static study by Mabie and others. The study was limited to the offset values that assure the pinion and gear teeth will neither be undercut nor become pointed. The analysis presented in this paper was performed using DANST-PC, a new version of the NASA gear dynamics code. The operating speed of the transmission influences the amount of hob offset required to equalize the dynamic stresses in the pinion and gear. The optimum hob offset for the pinion was found to vary within a small range as the speed changes. The optimum value is generally greater than the optimum value found by static procedures. For gears that must operate over a wide range of speeds, an average offset value may be used.

Lin, Hsiang Hsi↗

NASA NTRS1996

Dynamic Forces in Spur Gears - Measurement, Prediction, and Code Validation

Measured and computed values for dynamic loads in spur gears were compared to validate a new version of the NASA gear dynamics code DANST-PC. Strain gage data from six gear sets with different tooth profiles were processed to determine the dynamic forces acting between the gear teeth. Results demonstrate that the analysis code successfully simulates the dynamic behavior of the gears. Differences between analysis and experiment were less than 10 percent under most conditions.

Oswald, Fred B.↗

NASA NTRS1996

Measurement of Gear Tooth Dynamic Friction

Measurements of dynamic friction forces at the gear tooth contact were undertaken using strain gages at the root fillets of two successive teeth. Results are presented from two gear sets over a range of speeds and loads. The results demonstrate that the friction coefficient does not appear to be significantly influenced by the sliding reversal at the pitch point, and that the friction coefficient values found are in accord with those in general use. The friction coefficient was found to increase at low sliding speeds. This agrees with the results of disc machine testing.

Rebbechi, Brian↗

NASA NTRS1996

Measurement of Gear Tooth Dynamic Friction

GEAR TEETH↗

NASA NTRS1996

Dynamic Analysis of Spur Gear Transmissions (DANST). PC Version 3.00 User Manual

DANST is a FORTRAN computer program for static and dynamic analysis of spur gear systems. The program can be used for parametric studies to predict the static transmission error, dynamic load, tooth bending stress and other properties of spur gears as they are influenced by operating speed, torque, stiffness, damping, inertia, and tooth profile. DANST performs geometric modeling and dynamic analysis for low- or high-contact-ratio spur gears. DANST can simulate gear systems with contact ratios ranging from one to three. It was designed to be easy to use and it is extensively documented in several previous reports and by comments in the source code. This report describes installing and using a new PC version of DANST, covers input data requirements and presents examples.

Oswald, Fred B.↗

NASA NTRS1995

Influence of tooth profile modification on spur gear dynamic tooth strain

This paper presents results of dynamic strain gage measurements performed on the NASA gear-noise rig. The experiments were part of a joint research program between NASA and the U.S. Army Research Laboratory to advance the technology of rotorcraft transmissions. Tests were performed on six sets of low contact ratio spur gears with different tooth profile modifications. Results presented include static and dynamic measurements of gear tooth strain taken over a matrix of operating conditions. The results demonstrate that a well-designed tooth profile modification can significantly reduce dynamic loads in spur gears, especially for gears which operate at high speed and under high torque. The two parabolic modifications tested were not as effective as linear modifications, possibly because the modification zone was too long.

Oswald, Fred B.↗

NASA NTRS1995

Using hob offset to balance dynamic strength in spur gears

This paper presents an analytical study on the effect of hob offset on the dynamic tooth strength of spur gears. The study was limited to equal and opposite offset values applied to the pinion and gear to maintain the standard operating center distance. The analysis presented in this paper was performed using a new version of the NASA gear dynamics code DANST. The operating speed of the transmission has a significant influence on the amount of hob offset required to equalize the dynamic stresses in the pinion and gear. In the transmission studied, at low speeds, the optimum hob offset value was found to fluctuate. At higher speeds, the optimum value was constrained by the minimum allowed thickness at the tip of the pinion tooth. For gears that must operate over a range of speeds, an average offset value may be used. Spur gears designed with the procedure presented here can have significant improvements in load capacity.

Liou, Chuen-Huei↗

NASA NTRS1995

Computing Contact Stresses In Gear Teeth

Improved method of computing contact stresses in gear teeth accounts for complicating effects like those of static and sliding friction. Provides iterative procedure for determination of contact region and nodal contact forces along with contact stresses. Method based on equations and computational procedure incorporating these effects routinely.

Oswald, Fred B.↗

NASA NTRS1994

Numerical Simulation Of Cutting Of Gear Teeth

Shapes of gear teeth produced by gear cutters of specified shape simulated computationally, according to approach based on principles of differential geometry. Results of computer simulation displayed as computer graphics and/or used in analyses of design, manufacturing, and performance of gears. Applicable to both standard and non-standard gear-tooth forms. Accelerates and facilitates analysis of alternative designs of gears and cutters. Simulation extended to study generation of surfaces other than gears. Applied to cams, bearings, and surfaces of arbitrary rolling elements as well as to gears. Possible to develop analogous procedures for simulating manufacture of skin surfaces like automobile fenders, airfoils, and ship hulls.

Oswald, Fred B.↗

NASA NTRS1994

Comparison of Transmission Error Predictions with Noise Measurements for Several Spur and Helical Gears

Measured sound power data from eight different spur, single and double helical gear designs are compared with predictions of transmission error by the Load Distribution Program. The sound power data was taken from the recent Army-funded Advanced Rotorcraft Transmission project. Tests were conducted in the NASA gear noise rig. Results of both test data and transmission error predictions are made for each harmonic of mesh frequency at several operating conditions. In general, the transmission error predictions compare favorably with the measured noise levels.

Houser, Donald R.↗

NASA NTRS1994

Studies Of Vibrations In Gearboxes

Three NASA technical memorandums summarize studies of vibrations in gearboxes. Directed toward understanding and reducing gearbox noise caused by coupling of vibrations from meshing gears, through gear shafts and their bearings, to surfaces of gearbox housings. Practical systems in which understanding and reduction of gearbox noise beneficial include helicopter, car, and truck transmissions; stationary geared systems; and gear-driven actuator systems.

Choy, Fred K.↗