Bimodal particle distributions for improved heat transfer in flowing packed bed heat exchangers
Not Available
Stout, Dallin↗
Engineering topics
Otanicar, Todd P.
Publications and source records attributed to Otanicar, Todd P..
Characterizing particle-based thermal storage performance using optical methods for use in next generation concentrating solar power plants
Concentrating Solar Power (CSP) generation is an attractive option for low-emission power generation; however, the high costs of thermal storage associated with concentrating solar create a large barrier for their use and adaptation into modern life. Lowering their operation costs, while maintaining high thermal storage and transfer performance is essential. Solid particle-based heat exchange systems can reduce CSP cost but are often less efficient. Efforts to increase their performance have led to use of binary size particle mixes. Presented is an optical-based thermal analysis technique used to measure near-wall thermal conductivity of particle beds essential in determining their heat exchanger efficiency. Modulated Photothermal Radiometry is used to make dynamic temperature measurements, allowing for the extraction of the most relevant thermal properties like thermal conductivity, specific heat, and effusivity. The system uses a modulated laser source causing a damped periodic heat flux, resulting in a frequency and thermal property dependent surface temperature, of which is measured using radiometry. Lock-In techniques are used to extrapolate the amplitude of the signal. Plotting the amplitude against the root angular frequency allows for effusivity measurement by ratio to a known sample. Using specific heat measurements from literature and density measurements, the thermal conductivity of the particle mixes can be calculated. The simplicity of MPTR to probe through the depth of the bed is ideal for use in CSP for dynamic thermal performance monitoring.
Corona, Javier↗
Prediction of curing kinetics of resorcinol‐added resole phenolic resins using differential scanning calorimetry for the fabrication of carbon/carbon composites
Phenolic resins are commonly used as carbon precursors for the fabrication of carbon/carbon composites due to their high carbon yield and aromatic nature. To decrease curing times, acid catalysts are generally used, but the addition of resorcinol was found to have a similar effect while being incorporated into the resin matrix with no contamination or corrosion issues. In this work, the curing kinetics of pure, 10, 20, and 30 wt% resorcinol-added phenolic resins were investigated through differential scanning calorimetry. Heating rates of 0.5, 1, 2.5, and 5°C min -1 were used with several curing models to predict isothermal curing. Averaged mean absolute error (MAE) for the isoconversional mathematical approaches namely Kissinger–Akahira–Sunose (MAE = 12.9 min), Flynn–Wall–Ozawa (15.8 min), and Vyazovkin (14 min) show that these methods provide the best predictions, attributed to their adoption of an activation energy that depends on the extent of cure (E a (α)). The Kissinger method (MAE = 36 min), which depends only on peak temperature with a constant activation energy assumption, and the data noise sensitive Friedman model (MAE = 1144.7 min) provide the least accurate results. Thermogravimetric analysis revealed that resorcinol decreases the curing times by up to 71% without lowering carbon yield.
36 MATERIALS SCIENCE↗
Bimodal particle distributions with increased thermal conductivity for solid particles as heat transfer media and storage materials
Solid particles are being considered in several high temperature thermal energy storage systems and as heat transfer media in a variety of advanced power generation systems, particularly in concentrated solar power plants. The downside of such an approach is the low overall heat transfer coefficients caused by the inherently low thermal conductivity values of the low-cost solid media when coupled to heat exchanger for the power cycle working fluid. Choosing the right particle size distribution, emittance, and material of the solid media can all make a substantial difference in packed bed thermal conductivity. Current research though exclusively focuses on continuous unimodal distributions of particles. Here, in this work, we propose the use of a binary particle system with a bimodal size distribution to significantly increase packed bed thermal conductivity by reducing packed bed porosity. This is the first study related to ceramic solid particle heat transfer that has considered the thermal conductivity of non-unimodal size distributions at room and elevated temperatures. The following study found that for the binary particle system using Carbo particles CP 16/30 – CP 70/140 where the large particle volume fraction was 50% there was an 17–47% increase in packed bed thermal conductivity when compared with a nearly unimodal particle size distribution of CP 16/30 between 50 and 300 °C. Two different porosity and effective thermal conductivity models were studied, with one providing better prediction of porosity but both effective thermal conductivity models providing less predictive capacity. Importantly this approach can have a substantial impact of thermal performance, with little to no impact on the particle cost.
36 MATERIALS SCIENCE↗