Engineering topics

Ottenstein, Neil

Publications and source records attributed to Ottenstein, Neil.

13 records

NASA NTRS2020

Operational Techniques for Dealing with Long Eclipses During the MMS Extended Mission

Launch window design for the Magnetospheric Multiscale (MMS) mission ensured that no excessive eclipses would be encountered during the prime mission. However, no orbit solutions exist that satisfy the eclipse constraints indefinitely: most extended mission years contain 1-3 eclipses long enough to potentially damage either the spacecraft or its scientific instruments. Two steps were taken to improve the situation. Firstly, raising apogee radius from 25 to 29.34 Earth radii altered the Sun-Earth-MMS phasing, so efficiently achieving reductions in the long eclipse durations. These maneuvers were performed early this year, in preparation for the first pair of long eclipses in August 2019. Secondly, a set of operational steps were taken around the time of the eclipses to help maintain spacecraft and instrument temperatures while preventing power load shedding. These operational steps included raising key onboard temperatures through adjusting the spacecraft attitude to tilt the instrument deck towards the Sun, and engaging select heaters prior to going into eclipses. In addition, all scientific instruments were turned off, as well as high-power, non-critical spacecraft systems, to conserve energy.These steps each came with trade-offs which will be discussed in the paper. Finally, the results that were obtained when the spacecraft experienced the first extremely long eclipses will be discussed, as will lessons learned for future long eclipses.

Williams, Trevor↗

NASA NTRS2019

Lunisolar Perturbations of High-Eccentricity Orbits Such as the Magnetospheric Multiscale Mission

For highly eccentric orbits such as that of the Magnetospheric Multiscale (MMS)mission, with apogee radius now 29.34 Earth radii, the third-body effects of Sun andMoon are the major perturbations. One key consequence is an oscillation in MMSperigee altitude, on an approximately 6 year cycle. This variation has already requiredperigee-raise maneuvers to avoid an untimely reentry. There is also a long-termevolution in the orientation of the MMS orbit, with period roughly twice as long. Thiseffect may potentially be useful for MMS science studies, as it can bring the spacecraftinto new regions of the magnetosphere.

Williams, Trevor↗

NASA NTRS2018

MMS Extended Mission Design: Evaluation of a Lunar Gravity Assist Option

This paper will describe a study that was carried out on the design of a set of maneuvers that were considered for the later stages of an extended mission of the Magnetospheric Multiscale (MMS) mission. The goal of these maneuvers was to put MMS into a significantly different orbit from those flown heretofore, so allowing science collection in a different region of the magnetosphere. This study was made feasible by the fact that the rate at which fuel is being consumed to maintain small formations on the MMS high-apogee orbit is less than expected pre-flight: the current consumption rate is only about 2 kg/yr/spacecraft. In addition, the spacecraft finished the prime mission with a significant amount of fuel remaining: this was about 1-sigma above the mean when compared with pre-launch Monte Carlo simulations. The resulting situation is similar to that of a libration orbit mission, where station-keeping requires so little fuel that any margin at all will lead to an extensive mission lifetime. In the case of MMS, the spacecraft could, if desired, perform formation flying in the current orbit for several decades. Alternatively, the spacecraft could use a significant fraction of the remaining fuel to perform major orbit modifications, while still leaving enough to conduct formation flying for on the order of a decade. The extended mission maneuvers studied here are further apogee-raises, with the goal of setting up one or more lunar gravity assists. Geometry dictates that a lunar encounter is only achievable when the MMS apogee vector lies approximately in the lunar orbit plane: this limits the possible dates to mid-2021 or early 2027.

Design↗

NASA NTRS2017

Results of the Apogee-Raising Campaign of the Magnetospheric Multiscale Mission

This paper describes the apogee-raising campaign of the Magnetospheric Multiscale mission, where the spacecraft increased their apogee radii from 12 to 25 Earth radii in a total of 98 maneuvers. These maneuvers included an initial formation resize set to spread the spacecraft apart for safety, 32 apogee-raise delta-v maneuvers, their associated slews, four perigee-raise maneuvers and the associated slews, and finally a set of maneuvers to get back into formation. These activities were all accomplished successfully and on schedule with no anomalies, and at a fuel consumption somewhat less than predicted. As a result, MMS was set up ready to carry out in situ studies of magnetic reconnection in the magnetotail, with sufficient fuel remaining for a significant extended mission.

Mission Design↗

NASA NTRS2017

Satellite Formation Flight Results from Phase 1 of the Magnetospheric Multiscale Mission

This paper describes the underlying dynamics of formation flying in a high-eccentricity orbit such as that of the Magnetospheric Multiscale mission. The GPS-based results used for MMS navigation are summarized, as well as the procedures that are used to design the maneuvers used to place the spacecraft into a tetrahedron formation and then maintain it. The details of how to carry out these maneuvers are then discussed. Finally, the numerical results that have been obtained concerning formation flying for the MMS mission to date (e.g. tetrahedron sizes flown, maneuver execution error, fuel usage, etc.) are presented in detail.

satellite formation flight↗

NASA NTRS2017

Conjunction Assessment Techniques and Operational Results from the Magnetospheric Multiscale Mission

This paper will describe the results that have been obtained to date during the MMS mission concerning conjunction assessment. MMS navigation makes use of a weak-signal GPS-based system: this allows signals to be received even when MMS is flying above the GPS orbits, producing a highly accurate determination of the four MMS orbits. This data is downlinked to the MMS Mission Operations Center (MOC) and used by the Flight Dynamics Operations Area (FDOA) for both maneuver design and conjunction assessment. The MMS fly in tetrahedron formations around apogee, in order to collect simultaneous particles and fields science data. The original plan was to fly tetrahedra between 10 and 160 km in size; however, after Phase 1a of the mission, the science team requested that smaller sizes be flown if feasible. After analysis (to be detailed in a companion paper), a new minimum size of 7 km was decided upon. Flying at this reduced scale size makes conjunction assessment between the MMS spacecraft even more important: the methods that are used by the MMS FDOA to address this problem will be described in the paper, and a summary given of the previous analyses that went into the development of these techniques. Details will also be given of operational experiences to date. Finally, two CA mitigation maneuver types that have been designed (but never yet required to actually be performed) will also be outlined.

conjunction Assessment↗

NASA NTRS2016

Magnetospheric Multiscale Mission Attitude Dynamics: Observations from Flight Data

Extensive flight data is being collected throughout the MMS mission that includes quantities that are of interest for attitude dynamics studies such as spin rate, spin axis orientation nutation rate, etc. One example of such data is the long-term evolution of the spin rates of the four spacecraft. Spikes in these rates are observed that are separated by the MMS orbital period (just under 24 hr) and occur around perigee due to gravity-gradient torque. Periodic discontinuities in spin rate are caused by the controller resetting the spin rate approximately to the nominal 3.1 RPM value at the time of each maneuver. In between, a slow decay in spin rate can be seen to occur. The paper will discuss various disturbance torque mechanisms that could potentially be responsible for this behavior: these include magnetic hysteresis, eddy currents, solar radiation pressure, and a possible interaction between gravity-gradient and wire boom flexibility effects. One additional disturbance mechanism is produced by the Active Spacecraft Potential Control (ASPOC) devices: these emit positive indium ions to keep the MMS spacecraft electrically neutral, so as not to corrupt the electric field observations that are made by some of the on-board instruments. The spin rate decays that could be produced by these various mechanisms will be quantified in the paper, and their signatures described. Comparing these with the observations from flight data then allow the most likely candidate to be determined.

DYNAMICS↗

NASA NTRS2016

Initial Satellite Formation Flight Results from the Magnetospheric Multiscale Mission

This paper describes the underlying dynamics of formation flying in a high-eccentricity orbit such as that of the Magnetospheric Multiscale mission. The GPS-based results used for MMS navigation is summarized, as well as the procedures that are used to design the maneuvers used to place the spacecraft into a tetrahedron formation and then maintain it. The details of how to carry out these maneuvers are then discussed. Finally, the numerical results that have been obtained concerning formation flying for the MMS mission to date (e.g. tetrahedron sizes flown, maneuver execution error, fuel usage, etc.) are presented in detail.

Conjunction↗

NASA NTRS2016

Magnetospheric Multiscale Mission Attitude Dynamics: Observations from Flight Data

The NASA Magnetospheric Multiscale mission, launched on Mar. 12, 2015, is flying four spinning spacecraft in highly elliptical orbits to study the magnetosphere of the Earth. Extensive attitude data is being collected, including spin rate, spin axis orientation, and nutation rate. The paper will discuss the various environmental disturbance torques that act on the spacecraft, and will describe the observed results of these torques. In addition, a slow decay in spin rate has been observed for all four spacecraft in the extended periods between maneuvers. It is shown that this despin is consistent with the effects of an additional disturbance mechanism, namely that produced by the Active Spacecraft Potential Control devices. Finally, attitude dynamics data is used to analyze a micrometeoroid/orbital debris impact event with MMS4 that occurred on Feb. 2, 2016.

Conjunction↗

NASA NTRS2016

Initial Satellite Formation Flight Results from the Magnetospheric Multiscale Mission

This paper will describe the results that have been obtained to date concerning MMS formation flying. The MMS spacecraft spin at a rate of 3.1 RPM, with spin axis roughly aligned with Ecliptic North. Several booms are used to deploy instruments: two 5 m magnetometer booms in the spin plane, two rigid booms of length 12.5 m along the positive and negative spin axes, and four flexible wire booms of length 60 m in the spin plane. Minimizing flexible motion of the wire booms requires that reorientation of the spacecraft spin axis be kept to a minimum: this is limited to attitude maneuvers to counteract the effects of gravity-gradient and apparent solar motion. Orbital maneuvers must therefore be carried out in essentially the nominal science attitude. These burns make use of a set of monopropellant hydrazine thrusters: two (of thrust 4.5 N) along the spin axis in each direction, and eight (of thrust 18 N) in the spin plane; the latter are pulsed at the spin rate to produce a net delta-v. An on-board accelerometer-based controller is used to accurately generate a commanded delta-v. Navigation makes use of a weak-signal GPS-based system: this allows signals to be received even when MMS is flying above the GPS orbits, producing a highly accurate determination of the four MMS orbits. This data is downlinked to the MMS Mission Operations Center (MOC) and used by the MOC Flight Dynamics Operations Area (FDOA) for maneuver design. These commands are then uplinked to the spacecraft and executed autonomously using the controller, with the ground monitoring the burns in real time.

satellite↗

NASA NTRS2007

Orbit Determination and Navigation of the Solar Terrestrial Relations Observatory (STEREO)

This paper provides an overview of the required upgrades necessary for navigation of NASA's twin heliocentric science missions, Solar TErestrial RElations Observatory (STEREO) Ahead and Behind. The orbit determination of the STEREO spacecraft was provided by the NASA Goddard Space Flight Center's (GSFC) Flight Dynamics Facility (FDF) in support of the mission operations activities performed by the Johns Hopkins University Applied Physics Laboratory (APL). The changes to FDF s orbit determination software included modeling upgrades as well as modifications required to process the Deep Space Network X-band tracking data used for STEREO. Orbit results as well as comparisons to independently computed solutions are also included. The successful orbit determination support aided in maneuvering the STEREO spacecraft, launched on October 26, 2006 (00:52 Z), to target the lunar gravity assists required to place the spacecraft into their final heliocentric drift-away orbits where they are providing stereo imaging of the Sun.

Mesarch, Michael↗

NASA NTRS2007

Orbit Determination and Navigation of the Solar Terrestrial Relations Observatory (STEREO)

This paper provides an overview of the required upgrades necessary for navigation of NASA's twin heliocentric science missions, Solar TErestrial RElations Observatory (STEREO) Ahead and Behind. The orbit determination of the STEREO spacecraft was provided by the NASA Goddard Space Flight Center's (GSFC) Flight Dynamics Facility (FDF) in support of the mission operations activities performed by the Johns Hopkins University Applied Physics Laboratory (APL). The changes to FDF's orbit determination software included modeling upgrades as well as modifications required to process the Deep Space Network X-band tracking data used for STEREO. Orbit results as well as comparisons to independently computed solutions are also included. The successful orbit determination support aided in maneuvering the STEREO spacecraft, launched on October 26, 2006 (00:52 Z), to target the lunar gravity assists required to place the spacecraft into their final heliocentric drift-away orbits where they are providing stereo imaging of the Sun.

Mesarch, Michael A.↗

NASA NTRS2003

Towards Automating Spacecraft Attitude Sensor Calibration

With a view towards reducing cost and complexity for spacecraft early mission support at the NASA Goddard Space Flight Center (GSFC), efforts are being made to automate the attitude sensor calibration process. This paper addresses one of the major components needed by such a system. The beneficiaries of an improved calibration process are missions that demand moderate to high precision attitude knowledge or that need to perform accurate attitude slews. Improved slew accuracy reduces the time needed for re-acquisition of fine-pointing after each attitude maneuver, Rapid target acquisition can be very important for astronomical targeting or for off-nadir surface feature targeting by Earth-oriented spacecraft. The normal sequence of on-orbit calibration starts with alignment calibration of the star trackers and possibly the Sun sensor. Their relative alignment needs to be determined using a sufficiently large data set so their fields of view are adequately sampled. Next, the inertial reference unit (IRU) is calibrated for corrections to its alignment and scale factors. The IRU biases are estimated continuously by the onboard attitude control system, but the IRU alignment and scale factors are usually determined on the ground using a batch-processing method on a data set that includes several slews sufficient to give full observability of all the IRU calibration parameters. Finally, magnetometer biases, alignment, and its coupling to the magnetic torquers are determined in order io improve momentum management and occasionally for use in the attitude determination system. The detailed approach used for automating calibrations will depend on whether the automated system resides on the ground or on the spacecraft with an ultimate goal of autonomous calibration. Current efforts focus on a ground-based system driving subsystems that could run either on the ground or onboard. The distinction is that onboard calibration should process the data sequentially rather than in a single large batch since onboard computer data storage is limited. Very good batch- processing calibration utilities have been developed and used extensively at NASA/GSFC for mission support but no sequential calibration utilities are available. To meet this need, this paper presents the mathematical description of a sequential IRU calibration system. The system has been tested using flight data from the Rossi X-ray Timing Explorer (RXTE) during a series of attitude slews. The paper also discusses the current state of the overall automated system and describes plans for adding sequential alignment calibration and other additions that will reduce the amount of analyst time and input.

Sedlak, Joseph↗